View DS26518_7034883.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 286 rev: 022007 note: some revisions of this device may incor porate deviations from published specifications known as erra ta. multiple revisions of any device may be simultaneously available through various sales channel s. for information about device errata, click here: www.maxim-ic.com/errata . DS26518 8-port t1/e1/j1 transceive r general description the DS26518 is a single-chip 8-port framer and line interface unit (liu) combination for t1, e1, and j1 applications. each port is independently configurable, supporting both long-haul and short-haul lines. the 8-port sct is software compatible with the ds26519 and nearly software compatible with the ds26528 and its derivatives. applications routers channel service units (csus) data service units (dsus) muxes switches channel banks t1/e1 test equipment functional diagram DS26518 t1/j1/e1 transceiver t1/e1/j1 network backplane tdm x8 ordering information part temp range pin-package DS26518g 0 c to +70 c 256 te-csbga DS26518g+ 0 c to +70 c 256 te-csbga DS26518gn -40c to +85 c 256 te-csbga DS26518gn+ -40c to +85 c 256 te-csbga + denotes lead-free/rohs compliant device. features eight complete t1, e1, or j1 long-haul/ short-haul transceivers (liu plus framer) independent t1, e1, or j1 selections for each transceiver fully internal impedance match, no external resistor software-selectable transmit- and receive- side termination for 100 t1 twisted pair, 110 j1 twisted pair, 120 e1 twisted pair, and 75 e1 coaxial applications hitless protection switching crystal-less jitter attenuators can be selected for transmit or receive path; jitter attenuator meets ets ctr 12/13, itu-t g.736, g.742, g.823, and at&t pub 62411 external master clock can be multiple of 2.048mhz or 1.544mhz for t1/j1 or e1 operation; this clock is internally adapted for t1 or e1 usage in the host mode receive-signal level indication from -2.5db to -36db in t1 mode and -2.5db to -44db in e1 mode in approximate 2.5db increments transmit open- and short-circuit detection liu los in accordance with g.775, ets 300 233, and t1.231 transmit synchronizer flexible signaling extraction and insertion using either the system interface or microprocessor port alarm detection and insertion t1 framing formats of d4, slc-96, and esf j1 support e1 g.704 and crc-4 multiframe t1-to-e1 conversion features continued in section 2 . www .maxim-ic.com
DS26518 8-port t1/e1/j1 transceiver 2 of 286 table of contents 1. detailed d escription.................................................................................................9 2. feature high lights ..................................................................................................10 2.1 g eneral ............................................................................................................................... .......10 2.2 l ine i nterface ............................................................................................................................10 2.3 c lock s ynthesizers ..................................................................................................................10 2.4 j itter a ttenuator .....................................................................................................................10 2.5 f ramer /f ormatter ....................................................................................................................11 2.6 s ystem i nterface ......................................................................................................................11 2.7 hdcl c ontrollers ...................................................................................................................12 2.8 t est and d iagnostics ................................................................................................................12 2.9 m icrocontroller p arallel p ort .............................................................................................12 2.10 s lave s erial p eripheral i nterface (spi) f eatures ............................................................12 3. applicat ions ...............................................................................................................13 4. specifications compli ance ................................................................................... 14 5. acronyms and gl ossary .......................................................................................16 6. major operatin g modes.........................................................................................17 7. block diag rams.........................................................................................................18 8. pin descri ptions ........................................................................................................20 8.1 p in f unctional d escription ......................................................................................................20 9. functional de scription .........................................................................................28 9.1 p rocessor i nterface ................................................................................................................28 9.1.1 spi serial port mode........................................................................................................... ................. 28 9.1.2 spi functional timing diagrams ................................................................................................. ........ 28 9.2 c lock s tructure .......................................................................................................................31 9.2.1 backplane cloc k generation ..................................................................................................... .......... 31 9.2.2 clko output cl ock generation................................................................................................... ........ 32 9.3 r esets and p ower -d own m odes ..............................................................................................33 9.4 i nitialization and c onfiguration ..............................................................................................34 9.4.1 example device initia lization and sequence ..................................................................................... .. 34 9.5 g lobal r esources ....................................................................................................................34 9.6 p er -p ort r esources ................................................................................................................34 9.7 d evice i nterrupts .....................................................................................................................34 9.8 s ystem b ackplane i nterface ...................................................................................................36 9.8.1 elastic stores ................................................................................................................. ...................... 36 9.8.2 ibo multip lexing ............................................................................................................... .................... 39 9.8.3 h.100 (ct bus) compatibility ................................................................................................... ........... 45 9.8.4 transmit and receive channel blocking r egister s............................................................................. 47 9.8.5 transmit fractional suppor t (gapped cloc k mode ) ............................................................................ 47 9.8.6 receive fractional support (gapped cloc k mode ) ............................................................................. 47 9.9 f ramers ............................................................................................................................... .......48 9.9.1 t1 framing..................................................................................................................... ...................... 48 9.9.2 e1 framing..................................................................................................................... ...................... 51 9.9.3 t1 transmit synchronizer ....................................................................................................... ............. 53 9.9.4 signaling ...................................................................................................................... ........................ 54 9.9.5 t1 data link................................................................................................................... ...................... 59 9.9.6 e1 data link................................................................................................................... ...................... 61 9.9.7 maintenance and alar ms ......................................................................................................... ............ 62
DS26518 8-port t1/e1/j1 transceiver 3 of 286 9.9.8 alarms ......................................................................................................................... ......................... 65 9.9.9 error count registers .......................................................................................................... ................ 67 9.9.10 ds0 monitori ng function........................................................................................................ .............. 69 9.9.11 transmit per-channel id le code ge neration ...................................................................................... 70 9.9.12 receive per-channel idle code insertion........................................................................................ .... 70 9.9.13 per-channel loopba ck ........................................................................................................... ............. 70 9.9.14 e1 g.706 intermediate crc-4 updating (e1 m ode only ) ................................................................... 70 9.9.15 t1 programmable in-ba nd loop code g enerator ............................................................................... 71 9.9.16 t1 programmable in-band loop code dete ction................................................................................ 72 9.9.17 framer payl oad loopbacks ....................................................................................................... .......... 73 9.10 hdlc c ontrollers ................................................................................................................74 9.10.1 receive hdlc controller........................................................................................................ ............. 74 9.10.2 transmit hdlc controller....................................................................................................... ............. 77 9.11 p ower -s upply d ecoupling ....................................................................................................79 9.12 l ine i nterface u nits (liu s )....................................................................................................80 9.12.1 liu oper ation.................................................................................................................. ..................... 82 9.12.2 transmitter .................................................................................................................... ....................... 83 9.12.3 receiver ....................................................................................................................... ........................ 86 9.12.4 hitless protection switching (hps)............................................................................................. ......... 90 9.12.5 jitter att enuator.............................................................................................................. ...................... 91 9.12.6 liu loopbacks .................................................................................................................. ................... 92 9.13 b it e rror -r ate t est f unction (bert) .................................................................................95 9.13.1 bert repetitive pattern set .................................................................................................... ........... 96 9.13.2 bert error counter............................................................................................................. ................ 96 10. device re gisters .......................................................................................................97 10.1 r egister l istings ...................................................................................................................97 10.1.1 global regist er li st........................................................................................................... ................... 98 10.1.2 framer regi ster list........................................................................................................... .................. 99 10.1.3 liu and bert regi ster list ..................................................................................................... .......... 106 10.2 r egister b it m aps ................................................................................................................107 10.2.1 global register bit map ........................................................................................................ ............. 107 10.2.2 framer regist er bit map ........................................................................................................ ............ 108 10.2.3 liu register bit map ........................................................................................................... ............... 117 10.2.4 bert register bit map .......................................................................................................... ............ 118 10.3 g lobal r egister d efinitions ...............................................................................................119 10.4 f ramer r egister d escriptions ...........................................................................................133 10.4.1 receive register descriptions.................................................................................................. ......... 133 10.4.2 transmit regist er descriptions................................................................................................. ......... 191 10.5 liu r egister d efinitions .....................................................................................................227 10.6 bert r egister d efinitions .................................................................................................237 11. functional timing ...................................................................................................245 11.1 t1 r eceiver f unctional t iming d iagrams ..........................................................................245 11.2 t1 t ransmitter f unctional t iming d iagrams ....................................................................250 11.3 e1 r eceiver f unctional t iming d iagrams ..........................................................................255 11.4 e1 t ransmitter f unctional t iming d iagrams ....................................................................259 12. operating para meters .........................................................................................264 12.1 t hermal c haracteristics ....................................................................................................265 12.2 l ine i nterface c haracteristics ..........................................................................................265 13. ac timing characteristics ..................................................................................266 13.1 m icroprocessor b us ac c haracteristics ........................................................................266 13.1.1 spi bus mode ................................................................................................................... ................. 266 13.2 jtag i nterface t iming .........................................................................................................277 14. jtag boundary scan and test access port ................................................278
DS26518 8-port t1/e1/j1 transceiver 4 of 286 14.1 tap c ontroller s tate m achine .........................................................................................279 14.1.1 test-logic- reset............................................................................................................... ................. 279 14.1.2 run-test -idle .................................................................................................................. ................... 279 14.1.3 select-d r-scan ................................................................................................................. ................ 279 14.1.4 capture-dr ..................................................................................................................... ................... 279 14.1.5 shift- dr....................................................................................................................... ....................... 279 14.1.6 exit1-dr ....................................................................................................................... ...................... 279 14.1.7 pause-dr....................................................................................................................... .................... 279 14.1.8 exit2-dr ....................................................................................................................... ...................... 279 14.1.9 update-dr ...................................................................................................................... ................... 279 14.1.10 select-i r-scan ................................................................................................................. .............. 279 14.1.11 capture-ir ..................................................................................................................... ................. 280 14.1.12 shift-ir....................................................................................................................... ..................... 280 14.1.13 exit1-ir....................................................................................................................... .................... 280 14.1.14 pause-ir....................................................................................................................... .................. 280 14.1.15 exit2-ir....................................................................................................................... .................... 280 14.1.16 update-ir ...................................................................................................................... ................. 280 14.2 i nstruction r egister ...........................................................................................................282 14.2.1 sample:preload ................................................................................................................. ......... 282 14.2.2 bypass ......................................................................................................................... .................... 282 14.2.3 extest ......................................................................................................................... .................... 282 14.2.4 clamp .......................................................................................................................... ..................... 282 14.2.5 highz .......................................................................................................................... ...................... 282 14.2.6 idcode ......................................................................................................................... .................... 282 14.3 jtag id c odes ......................................................................................................................283 14.4 t est r egisters .....................................................................................................................283 14.4.1 boundary scan register ......................................................................................................... ........... 283 14.4.2 bypass register ................................................................................................................ ................. 283 14.4.3 identificati on regi ster........................................................................................................ ................. 283 15. pin config uration...................................................................................................284 15.1 p in c onfiguration ?256-b all te-csbga ..........................................................................284 16. package info rmation ............................................................................................285 16.1 256-b all te-csbga (56-g6028-001)...................................................................................285 17. document revision histor y ................................................................................286
DS26518 8-port t1/e1/j1 transceiver 5 of 286 list of figures figure 7-1. bl ock diagram ...................................................................................................... ................................... 18 figure 7-2. detail ed block di agram............................................................................................. .............................. 19 figure 9-1. spi serial port access for read mode, spi_cpol = 0, spi_cpha = 0 ............................................... 29 figure 9-2. spi serial port access for read mode, spi_cpol = 1, spi_cpha = 0 ............................................... 29 figure 9-3. spi serial port access for read mode, spi_cpol = 0, spi_cpha = 1 ............................................... 29 figure 9-4. spi serial port access for read mode, spi_cpol = 1, spi_cpha = 1 ............................................... 29 figure 9-5. spi serial port access for write mode, spi_cpol = 0, spi_cpha = 0 ............................................... 30 figure 9-6. spi serial port access for write mode, spi_cpol = 1, spi_cpha = 0 ............................................... 30 figure 9-7. spi serial port access for write mode, spi_cpol = 0, spi_cpha = 1 ............................................... 30 figure 9-8. spi serial port access for write mode, spi_cpol = 1, spi_cpha = 1 ............................................... 30 figure 9-9. backpla ne clock generation......................................................................................... .......................... 31 figure 9-10. device interrupt information fl ow diagram......................................................................... .................. 35 figure 9-11. ibo multiplexer e quivalent circ uit?4.096mhz ....................................................................... ............. 40 figure 9-12. ibo multiplexer e quivalent circ uit?8.192mhz ....................................................................... ............. 41 figure 9-13. ibo multiplexer e quivalent circ uit?16.384mhz ...................................................................... ............ 42 figure 9-14. rsyncn input in h.100 (ct bus) mode............................................................................... ................ 46 figure 9-15. tssyncion (input mode) input in h.100 (ct bus) mode ............................................................... .... 46 figure 9-16. crc-4 re calculate method .......................................................................................... ........................ 70 figure 9-17. hdlc mess age receive example...................................................................................... .................. 76 figure 9-18. hdlc messa ge transmit example..................................................................................... .................. 78 figure 9-19. network connecti on?longitudinal protection ........................................................................ ............. 81 figure 9-20. t1/j1 transm it pulse te mplates .................................................................................... ...................... 84 figure 9-21. e1 transm it pulse templates ....................................................................................... ........................ 85 figure 9-22. receive liu termination options ................................................................................... ...................... 87 figure 9-23. typical mo nitor application ....................................................................................... ............................ 88 figure 9-24. hps block diagram................................................................................................. .............................. 90 figure 9-25. jitte r attenuation ................................................................................................ ................................... 91 figure 9-26. loop back diag ram .................................................................................................. .............................. 92 figure 9-27. a nalog loopback................................................................................................... ................................ 92 figure 9-28. loc al loopback .................................................................................................... ................................. 93 figure 9-29. remo te loopback 2 ................................................................................................. ............................. 93 figure 9-30. d ual loopback ..................................................................................................... ................................. 94 figure 11-1. t1 rece ive-side d4 timing ......................................................................................... ....................... 245 figure 11-2. t1 rece ive-side esf timing........................................................................................ ...................... 245 figure 11-3. t1 receive- side boundary timing (ela stic store disabled).......................................................... ..... 246 figure 11-4. t1 receive-si de 1.544mhz boundary timing (e lastic store enabled).............................................. 246 figure 11-5. t1 receive-si de 2.048mhz boundary timing (e lastic store enabled).............................................. 247 figure 11-6. t1 receive-side inte rleave bus operat ion?byte mode................................................................ .. 248 figure 11-7. t1 receive-side interl eave bus operatio n?frame mode .............................................................. 2 49 figure 11-8. t1 receive-side rc hclkn gapped mode during f-bit.................................................................. .. 249 figure 11-9. t1 transm it-side d4 timing ........................................................................................ ....................... 250 figure 11-10. t1 transm it-side esf timing...................................................................................... ..................... 250 figure 11-11. t1 transmit -side boundary timing (ela stic store disabled)........................................................ .... 251 figure 11-12. t1 transmit-side 1.544mhz bo undary timing (elast ic store enabled) ........................................... 251 figure 11-13. t1 transmit-side 2.048mhz bo undary timing (elast ic store enabled) ........................................... 252 figure 11-14. t1 transmit-side in terleave bus oper ation?byte mode.............................................................. . 253 figure 11-15. t1 transmit-side inte rleave bus operati on?frame mode ........................................................... 25 4 figure 11-16. t1 transmit-side tchclkn gapped mode during f- bit ................................................................ . 254 figure 11-17. e1 re ceive-side timing........................................................................................... ......................... 255
DS26518 8-port t1/e1/j1 transceiver 6 of 286 figure 11-18. e1 receive-side boundary timing (elastic store dis abled) ......................................................... ... 255 figure 11-19. e1 receive-side 1.544mhz bou ndary timing (elastic store e nabled) ............................................ 256 figure 11-20. e1 receive-side 2.048mhz bou ndary timing (elastic store e nabled) ............................................ 256 figure 11-21. e1 receive-side inte rleave bus operat ion?byte mode ............................................................... 257 figure 11-22. e1 receive-side interl eave bus operati on?frame mode ............................................................ 25 8 figure 11-23. e1 receive-side rchclk n gapped mode duri ng channel 1 ........................................................ 258 figure 11-24. e1 tran smit-side timing.......................................................................................... ......................... 259 figure 11-25. e1 transmit -side boundary timing (ela stic store disabled) ........................................................ ... 259 figure 11-26. e1 transmit-side 1.544mhz bo undary timing (elast ic store enabled) ........................................... 260 figure 11-27. e1 transmit-side 2.048mhz bo undary timing (elast ic store enabled) ........................................... 260 figure 11-28. e1 transmit-side in terleave bus oper ation?byte mode .............................................................. 261 figure 11-29. e1 transmit-side inte rleave bus operati on?frame mode ........................................................... 26 2 figure 11-30. e1 g.802 ti ming .................................................................................................. ............................. 263 figure 11-31. e1 transmit-side tchc lkn gapped mode duri ng channel 1 ........................................................ 263 figure 13-1. spi inte rface timi ng diagram ...................................................................................... ....................... 267 figure 13-2. intel bus r ead timing (bts = 0) ................................................................................... ..................... 269 figure 13-3. intel bus wr ite timing (b ts = 0).................................................................................. ....................... 269 figure 13-4. motorola bus read timing (bts = 1) ................................................................................ ................. 270 figure 13-5 motorola bus write timing (bts = 1) ................................................................................ .................. 270 figure 13-6. receive framer ti ming?backplane (t1 mode)......................................................................... ........ 272 figure 13-7. receive-si de timing?elastic st ore enabled (t1 mode) ............................................................... .... 273 figure 13-8. receive fram er timing?l ine side ................................................................................... ................. 273 figure 13-9. transmit form atter timing ?backplane ............................................................................... .............. 275 figure 13-10. transmit formatter timing?elastic store enabled.................................................................. ........ 276 figure 13-11. bpc lk1 timing.................................................................................................... ............................. 276 figure 13-12. jtag interf ace timing diagram.................................................................................... .................... 277 figure 14-1. jtag functi onal block diagram ..................................................................................... .................... 278 figure 14-2. tap contro ller state diagram...................................................................................... ....................... 281
DS26518 8-port t1/e1/j1 transceiver 7 of 286 list of tables table 4-1. t1-related teleco mmunications specifications ........................................................................ .............. 14 table 4-2. e1-related teleco mmunications specifications ........................................................................ .............. 15 table 5-1. time slot numbering schemes......................................................................................... ....................... 16 table 8-1. detailed pin descriptions ........................................................................................... .............................. 20 table 9-1. clko fr equency selection ............................................................................................ .......................... 32 table 9-2. rese t functions..................................................................................................... ................................... 33 table 9-3. registers relate d to the elas tic store.............................................................................. ........................ 36 table 9-4. elastic store de lay after init ialization............................................................................ ........................... 37 table 9-5. registers relate d to the ibo multiplexer ............................................................................ ..................... 39 table 9-6. rsern output pin definitions (gtc r1.gibo = 0)....................................................................... ........... 43 table 9-7. rsign output pin definitions (gtc r1.gibo = 0) ....................................................................... ............ 43 table 9-8. tsern input pin de finitions (gtc r1.gibo = 0) ........................................................................ ............. 44 table 9-9. tsign input pin de finitions (gtcr1.gibo = 0) ........................................................................ .............. 44 table 9-10. rsyncn input pin definitions (gtc r1.gibo = 0) ...................................................................... .......... 45 table 9-11. d4 framing mode.................................................................................................... ............................... 48 table 9-12. esf framing mode ................................................................................................... ............................. 49 table 9-13. sl c-96 fram ing ..................................................................................................... ................................ 49 table 9-14. e1 f as/nfas framing ................................................................................................ .......................... 51 table 9-15. registers relat ed to setting up the framer ......................................................................... ................. 52 table 9-16. registers related to the transmit synchronizer..................................................................... ............... 53 table 9-17. registers related to signaling ..................................................................................... .......................... 54 table 9-18. registers related to slc-96........................................................................................ .......................... 57 table 9-19. registers rela ted to t1 transmit boc............................................................................... ................... 59 table 9-20. registers rela ted to t1 re ceive boc................................................................................ ................... 59 table 9-21. registers related to t1 tr ansmit fdl............................................................................... .................... 60 table 9-22. registers rela ted to t1 re ceive fdl................................................................................ .................... 60 table 9-23. registers rela ted to e1 data link .................................................................................. ....................... 61 table 9-24. registers relat ed to mainten ance and al arms........................................................................ .............. 63 table 9-25. t1 alarm criteria .................................................................................................. .................................. 65 table 9-26. registers related to transmit rai (yellow alarm) ................................................................... ............. 65 table 9-27. registers related to receive rai (y ellow al arm) .................................................................... ............. 66 table 9-28. t1 line code vi olation counti ng options ............................................................................ .................. 67 table 9-29. e1 line code vi olation counti ng options ............................................................................ .................. 67 table 9-30. t1 path code viol ation counting arrangements ....................................................................... ............ 68 table 9-31. t1 frames out of sync counting arrangements ........................................................................ ........... 68 table 9-32. registers rela ted to ds0 monitoring ................................................................................ ..................... 69 table 9-33. registers related to t1 in-band loop code generator ................................................................ ........ 71 table 9-34. registers related to t1 in-band loop code detection ................................................................ ......... 72 table 9-35. register related to framer pa yload loopbacks ....................................................................... ............ 73 table 9-36. registers related to the hdlc ...................................................................................... ........................ 74 table 9-37. recommended supply de coupling ...................................................................................... .................. 79 table 9-38. registers related to control of the liu............................................................................ ...................... 82 table 9-39. telecommunications specificat ion compliance for ds 26518 transm itters .......................................... 83 table 9-40. transfor mer specifications......................................................................................... ............................ 83 table 9-41. t1.231, g.775, and ets 300 233 loss criteria specifications........................................................ ...... 89 table 9-42. jitter attenuator standards compli ance............................................................................. .................... 91 table 9-43. registers related to confi gure, control, and status of bert........................................................ ....... 95 table 10-1. register a ddress ranges (in hex)................................................................................... ...................... 97 table 10-2. global register list ............................................................................................... ................................. 98
DS26518 8-port t1/e1/j1 transceiver 8 of 286 table 10-3. framer register list ............................................................................................... ................................ 99 table 10-4. liu register list .................................................................................................. ................................. 106 table 10-5. bert register list ................................................................................................. .............................. 106 table 10-6. global r egister bit map............................................................................................ ............................ 107 table 10-7. framer register bit map ............................................................................................ .......................... 108 table 10-8. liu r egister bit map ............................................................................................... ............................. 117 table 10-9. bert re gister bit map .............................................................................................. .......................... 118 table 10-10. global register set ............................................................................................... ............................. 119 table 10-11. output status control ............................................................................................. ............................ 120 table 10-12. master clock input se lection...................................................................................... ........................ 123 table 10-13. backplane reference clock select .................................................................................. .................. 124 table 10-14. device id codes in this product family ............................................................................ ................. 126 table 10-15. liu register set .................................................................................................. ............................... 227 table 10-16. transmit load impedance selection................................................................................. ................. 229 table 10-17. transmit pulse shape se lection .................................................................................... .................... 229 table 10-18. receiv e level i ndication .......................................................................................... .......................... 234 table 10-19. receive impedance selection....................................................................................... ..................... 235 table 10-20. receiver sensitivity se lection with monito r mode di sabled......................................................... ...... 236 table 10-21. receiver sensitivity se lection with monito r mode enabled .......................................................... ..... 236 table 10-22. bert register set ................................................................................................. ............................ 237 table 10-23. bert pattern select ............................................................................................... ........................... 239 table 10-24. bert e rror insert ion rate ......................................................................................... ........................ 240 table 10-25. bert repetiti ve pattern length se lect ............................................................................. ................ 240 table 12-1. recommended dc operating conditions ................................................................................ ............ 264 table 12-2. c apacitance........................................................................................................ .................................. 264 table 12-3. recommended dc operating conditions ................................................................................ ............ 264 table 12-4. thermal characteristics............................................................................................ ............................ 265 table 12-5. transmitte r characteristics........................................................................................ ........................... 265 table 12-6. receiver characteristics........................................................................................... ............................ 265 table 13-1. spi bus mode timing................................................................................................ ........................... 266 table 13-2. ac characteristi cs?microprocessor bus timing ....................................................................... ......... 268 table 13-3. receiver ac characteristics ........................................................................................ ........................ 271 table 13-4. transmit ac characteristics........................................................................................ ......................... 274 table 13-5. jtag interface timing.............................................................................................. ............................ 277 table 14-1. instruct ion codes for ieee 1149.1 archit ecture..................................................................... .............. 282 table 14-2. id code structure.................................................................................................. ............................... 283
DS26518 8-port t1/e1/j1 transceiver 9 of 286 1. detailed description the DS26518 is an 8-port monolithic device featuring indepe ndent transceivers that can be software configured for t1, e1, or j1 operation. each transceiver is composed of a line interface unit, framer, hdlc controller, elastic store, and a tdm backplane interface. the DS26518 is cont rolled via an 8-bit parallel port or the spi port. internal impedance matching and termination is provided for both tr ansmit and receive paths, reducing external component count. the liu is composed of a transmit interface, receive in terface, and a jitter attenuator. the transmit interface is responsible for generating the necessary waveshapes fo r driving the network and prov iding the correct source impedance depending on the type of media used. t1 wavefo rm generation includes dsx-1 line build-outs as well as csu line build-outs of 0db, -7.5db , -15db, and -22.5db. e1 waveform generation includes g.703 waveshapes for both 75 coax and 120 twisted cables. the receive interface provid es network termination and recovers clock and data from the network. the receive sensitivity adjusts automatically to the incoming signal level and can be programmed for 0db to -43db or 0db to -12db for e1 appl ications and 0db to -15db or 0db to -36db for t1 applications. the jitter attenuator removes phase jitter from t he transmitted or received signal. the crystal-less jitter attenuator requires only a t1 or e1 clock rate, or mult iple thereof, for both e1 and t1 applications, and can be placed in either transmit or receive data paths. on the transmit side, clock, data, and frame-sync signals are provided to the framer by the backplane interface section. the framer inserts the approp riate synchronization framing patterns, alarm information, calculates and inserts the crc codes, and provides the b8zs/hdb3 (zero code suppressi on) and ami line coding. the receive- side framer decodes ami, b8zs, and hdb3 line coding, synchronizes to the data stream, reports alarm information, counts framing/coding/crc errors, and provides clock, data, and frame-sync signals to the backplane interface section. both transmit and receive paths have access to an hdlc controller. the hdlc controller transmits and receives data via the framer block. the hdlc controller can be assign ed to any time slot, a portion of a time slot or to fdl (t1) or sa bits (e1). each controller has 64-byte fifo s, reducing the amount of processor overhead required to manage the flow of data. the backplane interface provides a versatile method of sending and receiving data from the host system. elastic stores provide a method for interfacing to asynchronous systems, converting from a t1/e1 network to a 2.048mhz, 4.096mhz, 8.192mhz, 16.384mhz, or n x 64khz system backpla ne. the elastic stores also manage slip conditions (asynchronous interface). an interleave bus option (ibo) is provided to allow up to eight transceivers (single DS26518) to share a high-speed backplane. the DS26518 also contains an internal clo ck adapter useful for the creation of a synchronous, high- frequency backplane timing source. the microprocessor port provides access for configurat ion and status of all the DS26518?s features. diagnostic capabilities include loopbacks, prbs pattern genera tion/detection, and 16-bit loop-up and loop-down code generation and detection.
DS26518 8-port t1/e1/j1 transceiver 10 of 286 2. feature highlights 2.1 general 17mm x 17mm, 256-pin te-csbga (1.00mm pitch) 3.3v supply with 5v tolerant inputs and outputs ieee 1149.1 jtag boundary scan development support includes evaluation kit, driver source code, and reference designs 2.2 line interface requires a single master clock (mclk) for both e1 and t1 operation. master clock can be 1.544mhz, 2.048mhz, 3.088mhz, 4.096mhz, 6.176mhz, 8. 192mhz, 12.352mhz, or 16.384mhz. fully software configurable short- and long-haul applications ranges include 0db to -43db, 0db to -30db, 0db to 20db, and 0db to -12db for e1; 0db to -36db, 0db to 30db, 0db to 20db, and 0db to -12db for t1 receiver signal level indication from -2.5db to -36db in t1 mode and -2.5db to -44db in e1 mode in 2.5db increments software-selectable receive termination for 75 , 100 , 110 , and 120 lines hitless protection switching monitor application gain settings of 14db, 20db, 26db, and 32db g.703 receive synchronization signal mode flexible transmit waveform generation t1 dsx-1 line build-outs t1 csu line build-outs of 0db , -7.5db, -15db, and -22.5db e1 waveforms include g.703 waveshapes for both 75 coax and 120 twisted cables analog loss-of-signal detection ais generation independent of loopbacks alternating ones and zeros generation receiver power-down transmitter power-down transmit outputs and receive inputs present a high impedance to the line when no power is applied, supporting redundancy applications transmitter short-circuit limiter with current-limit-exceeded indication transmit open-circuit-detected indication 2.3 clock synthesizers backplane clocks output frequencies include 2.048mhz, 4.096mhz, 8.192mhz, and 16.384mhz ? derived from user-selected recove red receive clock or refclkio clko output clock selectable from a wide range of frequencies referenced to mclk 2.4 jitter attenuator 32-bit or 128-bit crystal-less jitter attenuator requires only a 1.544mhz or 2.048mhz master clock or multiple thereof, for both e1 and t1 operation can be placed in either the receive or transmit path or disabled limit trip indication
DS26518 8-port t1/e1/j1 transceiver 11 of 286 2.5 framer/formatter fully independent transmit and receive functionality full receive and transmit path transparency t1 framing formats d4 and esf per t1.403 and expanded slc-96 support (tr-tsy-008) e1 fas framing and crc-4 multiframe per g.704/g.706, and g.732 cas multiframe transmit-side synchronizer transmit midpath crc recalculate (e1) detailed alarm and status reporting with optional interrupt support large path and line error counters ? t1: bpv, cv, crc-6, and framing bit errors ? e1: bpv, cv, crc-4, e-bit, and frame alignment errors ? timed or manual update modes ds1 idle code generation on a per-channel basis in both transmit and receive paths ? user defined ? digital milliwatt ansi t1.403-1999 support g.965 v5.2 link detect ability to monitor one ds0 channel in both the transmit and receive paths in-band repeating pattern generators and detectors ? three independent generators and detectors ? patterns from 1 to 8 bits or 16 bits in length bit oriented code (boc) support flexible signaling support ? software or hardware based ? interrupt generated on change of signaling data ? optional receive signaling freeze on loss of frame, loss of signal, or frame slip ? hardware pins provided to indicate loss of frame (lof ), loss of signal (los), loss of transmit clock (lotc), or signaling freeze condition automatic rai generation to ets 300 011 specifications rai-ci and ais-ci support expanded access to sa and si bits option to extend carrier loss criteria to a 1ms period as per ets 300 233 japanese j1 support ability to calculate and check crc-6 according to the japanese standard ability to generate yellow alarm according to the japanese standard t1-to-e1 conversion 2.6 system interface independent two-frame receive and transmit elastic stores independent control and clocking controlled slip capability with status minimum delay mode supported flexible tdm backplane supports bus rates from 1.544mhz to 16.384mhz supports t1 to cept (e1) conversion programmable output clocks for fractional t1, e1, h0, and h12 applications interleaving pcm bus operation hardware signaling capability receive signaling reinsertion to a backplane multiframe sync availability of signaling in a separate pcm data stream
DS26518 8-port t1/e1/j1 transceiver 12 of 286 signaling freezing ability to pass the t1 f-bit position through the elastic stores in the 2.048mhz backplane mode user-selectable synt hesized clock output 2.7 hdcl controllers one hdlc controller engine for each t1/e1 port independent 64-byte rx and tx buffers with interrupt support access fdl, sa, or single ds0 channel compatible with polled or interrupt driven environments 2.8 test and diagnostics ieee 1149.1 support per-channel programmable on-chip bit error-rate testing (bert) pseudorandom patterns including qrss user-defined repetitive patterns daly pattern error insertion single and continuous total-bit and errored-bit counts payload error insertion error insertion in the payload portion of the t1 frame in the transmit path errors can be inserted over the ent ire frame or selected channels insertion options include continuous and absol ute number with selectable insertion rates f-bit corruption for line testing loopbacks (remote, local, analog, and per-channel loopback) 2.9 microcontroller parallel port 8-bit parallel control port intel or motorola nonmultiplexed support flexible status registers support polled, interrupt, or hybrid program environments software reset supported hardware reset pin software access to devic e id and silicon revision 2.10 slave serial periphera l interface (spi) features software access to devic e id and silicon revision three-wire synchronous serial data link operat ing in full-duplex slave mode up to 5mbps glueless connection and fully compliant to motorola popular communication processors such as mpc8260 and microcontrollers such as m68hc11 software provision ability for active p hase of the serial clock (i.e., rising edge vs. falling edge), bit ordering of the serial data (most significant first vs. least significant bit first) flexible status registers support polled, interrupt, or hybrid program environments
DS26518 8-port t1/e1/j1 transceiver 13 of 286 3. applications the DS26518 is useful in applications such as: routers channel service units (csus) data service units (dsus) muxes switches channel banks t1/e1 test equipment
DS26518 8-port t1/e1/j1 transceiver 14 of 286 4. specifications compliance the DS26518 meets all the latest relev ant telecommunications specifications. table 4-1 provides the t1 specifications and table 4-2 provides the e1 specifications and rele vant sections that are applicable to the DS26518. table 4-1. t1-related tel ecommunications specifications ansi t1.102: digital hierarchy electrical interface ami coding b8zs substitution definition ds1 electrical interface. line rate 32ppm; pulse amplitude between 2.4v to 3.6v peak; power level between 12.6dbm to 17.9dbm. the t1 pulse mask is provided that we comply. dsx-1 for cross connects the return loss is greater than -26db. the dsx-1 cable is restricted up to 655 feet. this specification also provides cable characteristics of dsx-cross connect cable?22 avg cables of 1000 feet. ansi t1.231: digital hierarchy?layer 1 in service performance monitoring bpv error definition; excessive zero definition; los description; ais definition. ansi t1.403: network and customer insta llation interface?ds1 electrical interface description of the measurement of the t1 characteristics?100 . pulse shape and template compliance according to t1.102; power level 12.4dbm to 19.7dbm when all ones are transmitted. lbo for the customer interface (ci) is specif ied as 0db, -7.5db, and -15db. line rate is 32ppm. pulse amplitude is 2.4v to 3.6v. ais generation as unframed all ones is defined. the total cable attenuation is defined as 22db. t he DS26518 functions with up to -36db cable loss. note that the pulse template defined by t1.403 and t1.102 ar e different, specifically at times 0.61, -0.27, -34, and 0.77. the DS26518 is compliant to both templates. pub 62411 this specification has tighter jitter tolerance and transfer characteristics than other specifications. the jitter transfer characteristics are tighter t han g.736 and jitter tolerance is tighter the g.823. (ansi) ?digital hierarchy?electrical interfaces? (ansi) ?digital hierarchy?formats specification? (ansi) ?digital hierarchy?layer 1 in-service digital transmission performance monitoring? (ansi) ?network and customer installati on interfaces?ds1 elec trical interface? (at&t) ?requirements for interfacing digital terminal equipment to services employing the extended super frame format? (at&t) ?high capacity digital servic e channel interface specification? (ttc) ?frame structures on primary and se condary hierarchical digital interfaces? (ttc) ?isdn primary rate user-network interface layer 1 specification?
DS26518 8-port t1/e1/j1 transceiver 15 of 286 table 4-2. e1-related tel ecommunications specifications itu-t g.703 physical/electrical characteristics of g.703 hierarchical digital interfaces defines the 2048kbps bit rate?2048 50ppm; the transmission media are 75 coax or 120 twisted pair; peak-to- peak space voltage is 0.237v; nominal pulse width is 244ns. return loss 51hz to 102hz is 6db, 102hz to 3072hz is 8db, 2048hz to 3072hz is 14db. nominal peak voltage is 2.37v for coax and 3v for twisted pair. the pulse template for e1 is defined in g.703. itu-t g.736 characteristics of synchronous digi tal multiplex equipment operating at 2048kbps the peak-to-peak jitter at 2048kbps must be less than 0.05ui at 20hz to 100hz. jitter transfer between 2.048 sync hronization signal and 2.048 transmission signal is provided. itu-t g.742 second-order digital multiplex equipment operating at 8448kbps the DS26518 jitter attenuator is complaint with jitter transfer curve for sinusoidal jitter input. itu-t g.772 this specification provides the method for using receiver for transceiver 0 as a monitor for the remaining seven transmitter/receiver combinations. itu-t g.775 an los detection criterion is defined. itu-t g.823 the control of jitter and wander within digi tal networks that are based on 2.048kbps hierarchy. g.823 provides the jitter amplitude tolerance at different fr equencies, specifically 20hz, 2.4khz, 18khz, and 100khz. ets 300 233 this specification provides los and ais signal criteria for e1 mode. pub 62411 this specification has tighter jitter tolerance and transfer characteristics than other specifications. the jitter transfer characteristics are tighter t han g.736 and jitter tolerance is tighter than g.823. (itu-t) ?synchronous frame structures used at 1544, 6312, 2048, 8488, and 44736kbps hierarchical levels? (itu-t) ?frame alignment and cyclic redundancy check (crc) procedures re lating to basic frame structures defined in recommendation g.704? (itu-t) ?characteristics of primary pcm mu ltiplex equipment operating at 2048kbps? (itu-t) characteristics of a sy nchronous digital multiplex e quipment operating at 2048kbps? (itu-t) ?loss of signal (los) and alarm indication signal (ais) defect detection and clearance criteria? (itu-t) ?the control of jitter and wander within digital networks which are based on the 2048kbps hierarchy? (itu-t) ?primary rate user-network interface?layer 1 specification? (itu-t) ?error performance m easuring equipment operating at the primary rate and above? (itu-t) ?in-service code violation monitors for digital systems? (ets) ?integrated services digital ne twork (isdn); primary rate user-netwo rk interface (uni); part 1/layer 1 specification? (ets) ?transmission and multiplexing; physical/electrical ch aracteristics of hierarchical digital interfaces for equipment using the 2048kbps-based plesiochr onous or synchronous digital hierarchies? (ets) ?integrated services digita l network (isdn); access digital section for isdn primary rate? (ets) ?integrated services digital netw ork (isdn); attachment requirements fo r terminal equipment to connect to an isdn using isdn primary rate access? (ets) ?business telecommunications (bt); open networ k provision (onp) technical requirements; 2048kbps digital unstructured leased lines (d2048u) attachment requirements for terminal equipment interface? (ets) ?business telecommunications (b tc); 2048kbps digital structured leased lines (d2048s); attachment requirements for terminal equipment interface? (itu-t) ?synchronous frame structures used at 1544, 6312, 2048, 8488, and 44736kbps hierarchical levels? (itu-t) ?frame alignment and cyclic redundancy check (crc) procedures re lating to basic frame structures defined in recommendation g.704?
DS26518 8-port t1/e1/j1 transceiver 16 of 286 5. acronyms and glossary this data sheet assumes a particular nomenclature of the t1 and e1 operating environment. in each 125 s t1 frame, there are 24 8-bit channels plus a framing bit. it is assumed that the framing bit is sent first followed by channel 1. for t1 and e1 each channel is made up of 8 bits, which are numbered 1 to 8. bit 1, the msb, is transmitted first. bit 8, the lsb, is transmitted last. locked refers to two clock signals that are phase- or fre quency-locked or derived from a common clock (i.e., a 1.544mhz clock can be locked to a 2.048mhz cloc k if they share the same 8khz component). table 5-1. time slot numbering schemes ts 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 phone channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
DS26518 8-port t1/e1/j1 transceiver 17 of 286 6. major operating modes the DS26518 has two major modes of operation: t1 mode and e1 mode. the mode of operation for each liu is configured in the ltrcr register. the mode of operation for each framer is configured in the tmmr register. j1 operation is a special case of t1 operating mode.
DS26518 8-port t1/e1/j1 transceiver 18 of 286 7. block diagrams figure 7-1. block diagram x8 DS26518 framer #8 framer #7 framer #6 ... framer #4 framer #3 framer #2 t1/e1 framer hdlc bert micro processor interface jtag port clock generation liu #8 liu #7 liu #6 ... liu #4 liu #3 liu #2 line interface unit interface #8 interface #7 interface #6 ... interface #4 interface #3 interface #2 backplane interface elastic stores rtip tring rring ttip controller port test port clock adapter receive backplane signals transmit backplane signals hardware alarm indicators x8 rtipe
DS26518 8-port t1/e1/j1 transceiver 19 of 286 figure 7-2. detailed block diagram clock synthesiz- er microprocessor interface jtag port reset block a[12:0] d[7:0] csb rdb/dsb wrb/rwb bts intb jtdi jtms jtclk jtdo jtrst resetb mclk rchblk/clkn tchblk/clkn tclkn tsern tsyncn/ tssyncion tsysclkn rsysclkn rsyncn rsern rclkn bpclk1 refclkio ttipn tringn rringn rtipn serial interface mode: spi (sclk, cpol, cpha, swap, mosi, and miso) rsign rm/rfsyncn tsign pre-scaler pll spi_sel clko transmit liu waveform shaper/line driver receive liu clock/data recovery jitter attenuator transmit enable tx bert rx bert tx hdlc rx hdlc tx framer: system if b8zs/ hdb3 encode elastic store rx framer: system if b8zs/ hdb3 decode elastic store alb llb flb rlb plb DS26518 transceiver 1 of 8 backplane interface
DS26518 8-port t1/e1/j1 transceiver 20 of 286 8. pin descriptions 8.1 pin functional description table 8-1. detailed pin descriptions name pin type function analog transmit ttip1 a1, a2 ttip2 h1, h2 ttip3 j1 j2 ttip4 t1, t2 ttip5 t15, t16 ttip6 j15, j16 ttip7 h15, h16 ttip8 a15, a16 analog output, high impedance transmit bipolar tip for transceiver 1 to 8. these pins are differential line driver tip outputs. these pins can be high impedance if: if txenable is low, ttipn/tringn will be high impedance. note that if txenable is low, the register settings for control of ttipn/tringn are ignored and output is high impedance. the differential outputs of ttipn and tringn can provide internal matched impedance for e1 75 , e1 120 , t1 100 , or j1 110 . the user can turn off internal termination. note: the two pins shown for each transmit bipolar tip (e.g., pins a1 and a2 for ttip1) should be tied together. tring1 a3, b3 tring2 g3, h3 tring3 j3, k3 tring4 r3, t3 tring5 r14,t14 tring6 j14, k14 tring7 g14, h14 tring8 a14, b14 analog output, high impedance transmit bipolar ring for transceiver 1 to 8. these pins are differential line driver ring outputs. these pins can be high impedance if: if txenable is low, ttipn/tringn will be high impedance. note that if txenable is low, the register settings for control of ttipn/tringn are ignored and output is high impedance. the differential outputs of ttipn and tringn can provide internal matched impedance for e1 75 , e1 120 , t1 100 , or j1 110 . the user can turn off internal termination. note: the two pins shown for each transmit bipolar ring (e.g., pins a3 and b3 for tring1) should be tied together. txenable/ scan_en l13 input transmit enable. if this pin is pulled low, all transmitter outputs (ttipn and tringn) are high impedance. the regist er settings for tri-state control of ttipn/tringn are ignored if txenable is low. if txenable is high, the particular driver can be tri-stated by the register settings. scan enable. when low, device is in normal operation. scan enable is selected by the scanmode pin. note: user should not select scan enable?test mode only. analog receive rtip1 c1 rtip2 f1 rtip3 l1 rtip4 p1 rtip5 p16 rtip6 l16 rtip7 f16 rtip8 c16 analog input receive bipolar tip for transceiver 1 to 8. the differential inputs of rtipn and rringn can provide internal matched impedance for e1 75 , e1 120 , t1 100 , or j1 110 . the user can turn off internal termination via the liu receive impedance and sensitivity monitor register ( lrismr ). rring1 c2 rring2 f2 rring3 l2 rring4 p2 rring5 p15 rring6 l15 rring7 f15 rring8 c15 analog input receive bipolar ring for transceiver 1 to 8. the differential inputs of rtipn and rringn can provide internal matched impedance for e1 75 , e1 120 , t1 100 , or j1 110 . the user has the option of turning off internal termination via the liu receive impedance and s ensitivity monitor register ( lrismr ). resref j5 input resistor reference. this pin is used to calibrate the internal impedance match resistors of the receive lius. this pin should be tied to v ss through a 10k 1% resistor.
DS26518 8-port t1/e1/j1 transceiver 21 of 286 name pin type function transmit framer tser1 f6 tser2 e7 tser3 r4 tser4 n7 tser5 m10 tser6 l11 tser7 f10 tser8 d12 input transmit nrz serial data 1 to 8. these pins are sampled on the falling edge of tclkn when the transmit-side elastic stor e is disabled. these pins are sampled on the falling edge of tsysclkn when the tr ansmit-side elastic store is enabled. in ibo mode, data for multiple framers can be used in high-speed multiplexed scheme. this is described in section 9.8.2 . the table there presents the combination of framer data for each of the streams. tsysclkn is used as a reference when ibo is invoked. see table 9-8 . tclk1 c5 tclk2 d7 tclk3 p5 tclk4 l8 tclk5 l10 tclk6 n11 tclk7 e10 tclk8 b13 input transmit clock 1 to 8. a 1.544mhz or a 2.048mhz primary clock. used to clock data through the transmit side of the tran sceiver. tsern data is sampled on the falling edge of tclkn. tclkn is used to sample tsern when the elastic store is not enabled or ibo is not used. tsysclk1 p13 input transmit system clock 1. 1.544mhz, 2.048mhz, 4.096mhz, 8.192mhz, or 16.384mhz clock. only used when the transmit-side elastic store function is enabled. should be tied low in applications that do not use the transmit-side elastic store. the clock can be 4.096m hz, 8.912mhz, or 16.384mhz when ibo mode is used. tsysclk1 does not have an internal pulldown resistor. note: if the gtcr1 .528md bit is set, tsysclk1 beco mes the master tsysclk for all framers. tsysclk2/ al/rsigf/flos2 f3 tsysclk3/ al/rsigf/flos3 l3 tsysclk4/ al/rsigf/flos4 p3 tsysclk5/ al/rsigf/flos5 p14 tsysclk6/ al/rsigf/flos6 l14 tsysclk7/ al/rsigf/flos7 f14 tsysclk8/ al/rsigf/flos8 c14 input with internal pulldown/ output transmit system clock 2 to 8. 1.544mhz, 2.048mhz, 4.096mhz, 8.192mhz, or 16.384mhz clock. only used when the transmit-side elastic store function is enabled. should be tied low in applications that do not use the transmit-side elastic store. the clock can be 4.096m hz, 8.912mhz, or 16.384mhz when ibo mode is used. tsysclk1 does not have an internal pulldown resistor. note: if the gtcr1 .528md bit is set, tsysclk1 beco mes the master tsysclk for all framers. analog loss/receive-signaling freeze/framer los. analog los reflects the los (loss of signal) detected by the liu front-end and framer los is los detection by the corresponding framer; the same pins can reflect receive- signaling freeze indications. this selection can be made by settings in the global transceiver clock control register 1 ( gtccr1 ). al/rsigf/flos[8:2] is available only by setting the gtcr1 .528md bit to 1. tsync1/ tssyncio1 b4 tsync2/ tssyncio2 f7 tsync3/ tssyncio3 m6 tsync4/ tssyncio4 m7 tsync5/ tssyncio5 n10 tsync6/ tssyncio6 t12 tsync7/ tssyncio7 b11 tsync8/ tssyncio8 a13 input/ output transmit synchronization 1 to 8. a pulse at these pins establishes either frame or multiframe boundaries for the transmit side. these signals can also be programmed to output either a frame or multiframe pulse. if these pins are set to output pulses at frame boundaries, they can also be set to output double-wide pulses at signaling frames in t1 m ode. the operation of these signals is synchronous with tclk[8:1]. transmit system synchronization in. these pins are selected when the transmit-side elastic store is enabled. a pulse at these pins establishes either frame or multiframe boundaries for the transmit side. should be tied low in applications that do not use the transmit-si de elastic store. the operation of this signal is synchronous with tsysclk[8:1]. transmit system synchronization out. if configured as an output and the transmit elastic store is enabled, an 8khz pulse synchronous to the bpclk1 will be generated. this pulse in combination with bpclk1 can be used as an ibo master. tssyncion can be used as a source to rsyncn and tssyncion of another DS26518 or rsync and tssync of other dallas semiconductor parts. note: tssyncio[8:1] are not used when gtcr1 .528md is set. when gtcr1 .528md is set, the tssyncio pin (n13) is used.
DS26518 8-port t1/e1/j1 transceiver 22 of 286 name pin type function tssyncio n13 input/ output note: in default operation, this pin is not used. when gtcr1 .528md is set, this pin is active. if pin is not used, tie low through a resistor. transmit system synchronization in. this pin is selected when the transmit- side elastic store is enabled. a pulse at this pin establishes either frame or multiframe boundaries for the transmit side. note that if the elastic store is enabled, frame or multiframe boundary will be established for all transmitters. should be tied low in applications that do not use the transmit-side elastic store. the operation of this signal is synchronous with tsysclkn. transmit system synchronization out. if configured as an output and the transmit-side elastic store is enabled, an 8khz pulse synchronous to bpclk1 will be generated. this pulse in combination with bpclk1 can be used as an ibo master. tssyncio can be used as a source to rsyncn and tssyncio of another DS26518 or rsync and tssync of other dallas semiconductor parts. tsig1 d5 tsig2 a6 tsig3 t4 tsig4 r6 tsig5 t10 tsig6 r12 tsig7 a11 tsig8 c13 input transmit signaling 1 to 8. when enabled, this input samples signaling bits for insertion into outgoing pcm data stream . sampled on the falling edge of tclkn when the transmit-side elastic store is disabled. sampled on the falling edge of tsysclkn when the transmit-side elastic store is enabled. in ibo mode, the tsign streams can run up to 16.384mhz. see table 9-9 . tchblk1/ tchclk1 a5 tchblk2/ tchclk2 c7 tchblk3/ tchclk3 l7 tchblk4/ tchclk4 p7 tchblk5/ tchclk5 p9 tchblk6/ tchclk6 p11 tchblk7/ tchclk7 d10 tchblk8/ tchclk8 e11 output transmit channel block/transmit channel block clock. a dual function pin. tchblk[1:8]. tchblkn is a user-programmable output that can be forced high or low during any of the channels. it is synchronous with tclkn when the transmit-side elastic store is disabled. it is synchronous with tsysclkn when the transmit-side elastic store is enabled. it is useful for blocking clocks to a serial uart or lapd controller in applications where not all channels are used such as fractional t1, fractional e1, 384kbps (h0), 768kbps, or isdn-pri. also useful for locating individual channels in drop- and-insert applications, for external per- channel loopback, and for per-channel conditioning. tchclk[1:8]. tchclkn is a 192khz (t1) or 256khz (e1) clock that pulses high during the lsb of each channel. it can also be programmed to output a gated transmit bit clock controlled by tchblkn. it is synchronous with tclkn when the transmit-side elastic store is disabled. it is synchronous with tsysclkn when the transmit-side elastic store is enabled. useful for parallel-to-serial conversion of channel data.
DS26518 8-port t1/e1/j1 transceiver 23 of 286 name pin type function receive framer rser1 e5 rser2 d6 rser3 n4 rser4 n6 rser5 m11 rser6 m12 rser7 b12 rser8 f11 output received serial data 1 to 8. received nrz serial data. updated on rising edges of rclkn when the receive-side elastic store is disabled. updated on the rising edges of rsysclkn when the receiv e-side elastic store is enabled. when ibo mode is used, the rsern pins can output data for multiple framers. the rsern data is synchronous to rsysclkn. see section 9.8.2 and table 9-6 . rclk1 f4 rclk2 g4 rclk3 l4 rclk4 m4 rclk5 k13 rclk6 j13 rclk7 f13 rclk8 e13 output receive clock 1 to 8. a 1.544mhz (t1) or 2.048mhz (e1) clock that is used to clock data through the receive-side framer. this clock is recovered from the signal at rtipn and rringn. rsern data is output on the rising edge of rclkn. rclkn is used to output rsern wh en the elastic store is not enabled or ibo is not used. when the elastic store is enabled or ibo is used, the rsern is clocked by rsysclkn. rsysclk1 l12 input receive system clock 1. 1.544mhz, 2.048mhz, 4.096mhz, 8.192mhz, or 16.384mhz receive backplane clock. only used when the receive-side elastic store function is enabled. should be tied low in applications that do not use the receive-side elastic store. multiple of 2.048mhz is expected when the ibo mode is used. note: if the gtcr1 .528md bit is set, rsysclk1 becomes the master rsysclk for all framers. rsysclk2/ rlf/ltc2 e3 rsysclk3/ rlf/ltc3 m3 rsysclk4/ rlf/ltc4 n3 rsysclk5/ rlf/ltc5 n14 rsysclk6/ rlf/ltc6 m14 rsysclk7/ rlf/ltc7 e14 rsysclk8/ rlf/ltc8 d14 input with internal pulldown/ output receive system clock 2 to 8. 1.544mhz, 2.048mhz, 4.096mhz, 8.192mhz, or 16.384mhz receive backplane clock. only used when the receive-side elastic store function is enabled. should be tied low in applications that do not use the receive-side elastic store. multiple of 2.048mhz is expected when the ibo mode is used. receive loss of frame/loss of transmit clock. this pin can also be programmed to either toggle high when th e synchronizer is searching for the frame and multiframe or to toggle high if the tclkn pin has not been toggled for approximately three clock periods. rlf/ltc[8:2] are available when gtcr1 .528md = 1. note: if the gtcr1 .528md bit is set, rsysclk1 becomes the master rsysclk for all framers. rsync1 a4 rsync2 b6 rsync2 n5 rsync2 t6 rsync5 r10 rsync6 p12 rsync7 c11 rsync8 d13 input/ output receive synchronization 1 to 8. if the receive-side elastic store is enabled, this signal is used to input a frame or mu ltiframe boundary pulse. if set to output frame boundaries, rsyncn can be programmed to output double-wide pulses on signaling frames in t1 mode. in e1 mode, rsyncn out can be used to indicate cas and crc-4 multiframe. the DS26518 can accept an h.100-compatible synchronization signal. the default directio n of this pin at power-up is input, as determined by the rsio control bit in the riocr .2 register.
DS26518 8-port t1/e1/j1 transceiver 24 of 286 name pin type function rmsync1/ rfsync1 c4 rmsync2/ rfsync2 c6 rmsync3/ rfsync3 p4 rmsync4/ rfsync4 p6 rmsync5/ rfsync5 p10 rmsync6/ rfsync6 n12 rmsync7/ rfsync7 d11 rmsync8/ rfsync8 e12 output receive multiframe/frame synchronization 1 to 8. a dual function pin to indicate frame or multiframe synchronization. rfsyncn is an extracted 8khz pulse, one rclkn wide that identifie s frame boundaries. rmsyncn is an extracted pulse, one rclkn wide (elastic store disabled) or one rsysclkn wide (elastic store enabled), t hat identifies multiframe bou ndaries. when the receive elastic store is enabled, the rmsyncn signal indicates the multiframe sync on the system (backplane) side of the elastic store. in e1 mode, this pin can indicate either the crc-4 or cas multiframe as determined by the rsms2 control bit in the receive i/o confi guration register ( riocr .1). rsig1 d4 rsig2 e6 rsig3 m5 rsig4 r5 rsig5 r11 rsig6 r13 rsig7 a12 rsig8 f12 output receive signaling 1 to 8. outputs signaling bits in a pcm format. updated on rising edges of rclkn when the receive-side elastic store is disabled. updated on the rising edges of rsysclkn when the receive-side elastic store is enabled. see table 9-7 . rchblk1/ rchclk1 e4 rchblk2/ rchclk2 b5 rchblk3/ rchclk3 l6 rchblk4/ rchclk4 t5 rchblk5/ rchclk5 t11 rchblk6/ rchclk6 t13 rchblk7/ rchclk7 c12 rchblk8/ rchclk8 g13 output receive channel block/receive channel block clock. this pin can be configured to output either rchblk or rchclk. rchblk[1:8]. rchblkn is a user-programmable output that can be forced high or low during any of the 24 t1 or 32 e1 channels. it is synchronous with rclkn when the receive-side elastic store is disabled. it is synchronous with rsysclkn when the receive-side elastic store is enabled. this pin is useful for blocking clocks to a serial uart or lapd controll er in applications wh ere not all channels are used such as fractional service, 384kbps service, 768kbps, or isdn-pri. also useful for locating individual channels in drop-and-insert applications, for external per-channel loopback, and for per-channel conditioning. rchclk[1:8]. rchclkn is a 192khz (t1) or 256khz (e1) clock that pulses high during the lsb of each channel. it is sy nchronous with rclkn when the receive- side elastic store is disabled. it is synchronous with rsysclkn when the receive-side elastic store is enabled. it is useful for parallel-to-serial conversion of channel data. bpclk1 e8 output backplane clock 1. programmable clock output that can be set to 2.048mhz, 4.096mhz, 8.192mhz, or 16.384mhz. the reference for this clock can be rclk[8:1], a 1.544mhz or 2.048mhz clock frequency derived from mclk, or an external reference clock (refclkio) . this allows system clocks to be referenced from external sources, the t1j1e1 recovered clocks, or the mclk oscillator. clko/ rlf/ltc1 d3 output clock out. clock output pin that can be pr ogrammed to output numerous frequencies referenced to mclk. frequencies available: 1.544mhz, 2.048mhz, 4.096mhz, 8.192mhz, 12.288mhz, 16.384mhz, 256khz, and 64khz. gtccr3 .clkosel[2:0] selects the frequency. receive loss of frame/loss of transmit clock. this pin can also be programmed to either toggle high when th e synchronizer is searching for the frame and multiframe, or to toggle high if the tclkn pin has not been toggled for approximately three clock periods. rlf/ltc1 is available on the DS26518 when gtcr1 .528md = 1.
DS26518 8-port t1/e1/j1 transceiver 25 of 286 name pin type function microprocessor interface a12 c8 a11 a8 a10 b8 a9 f8 a8 b9 a7 a9 a6 c9 a5 d9 a4 e9 a3 f9 a2 b10 a1 a10 a0 c10 input address [12:0]. this bus selects a specific r egister in the DS26518 during read/write access. a12 is the msb and a0 is the lsb. d[7]/spi_cpol t9 input/ output data [7]/spi interf ace clock polarity d[7]: bit 7 of the 16-bit or 8-bit data bus used to input data during register writes and data outputs during register reads. not driven when csb = 1. spi_cpol: this signal selects the clock polarity when spi_sel = 1. see section 9.1.2 for detailed timing and functionalit y information. defaul t setting is low. d[6]/spi_cpha n9 input/ output data [6]/spi interface clock phase d[6]: bit 6 of the 16-bit or 8-bit data bus used to input data during register writes and data outputs during register reads. not driven when csb = 1. spi_cpha: this signal selects the clock phase when spi_sel = 1. see section 9.1.2 for detailed timing and functionalit y information. defaul t setting is low. d[5]/spi_swap m9 input/ output data [5]/spi bit order swap d[5]: bit 5 of the 16-bit or 8-bit data bus used to input data during register writes and data outputs during register reads. not driven when csb = 1. spi_swap: this signal is active when spi_sel = 1. the address and data bit order is swapped when spi_swap is hi gh. the r/w and b bit positions are never changed in the control word. 0 = lsb is transmitted and received first. 1 = msb is transmitted and received first. d[4] r8 input/ output data [4]. bit 4 of the 8-bit data bus used to input data during register writes and data outputs during register reads. not driven when csb = 1. d[3] t8 input/ output data [3]. bit 3 of the 8-bit data bus used to input data during register writes and data outputs during register reads. not driven when csb = 1. d[2]/spi_sclk p8 input/ output data [2]/spi serial interface clock d[2]: bit 2 of the 8-bit data bus used to in put data during regist er writes and data outputs during register reads. not driven when csb = 1. spi_sclk: spi serial clock input when spi_sel = 1. d[1]/spi_mosi l9 input/ ouput data [1]/spi serial interface data master out-slave in d[1]: bit 1 of the 8-bit data bus used to input data during register writes, and data outputs during register reads. not driven when csb = 1. spi_mosi: spi serial data input (master ou t-slave in) when spi_sel = 1. d[0]/spi_miso n8 input/ output data [0]/spi serial interface data master in-slave out d[0]: bit 0 of the 8-bit data bus used to in put data during regist er writes and data outputs during register reads. not driven when csb = 1. spi_miso: spi serial data output (master in-slave out) when spi_sel = 1. csb t7 input chip-select bar. this active-low signal is used to qualify register read/write accesses. the rdb/dsb and wrb signals are qualified with csb. rdb / dsb m8 input read-data bar/data-strobe bar. this active-low signal along with csb qualifies read access to one of the DS26518 regist ers. the DS26518 drives the data bus with the contents of the addressed register while rdb and csb are low.
DS26518 8-port t1/e1/j1 transceiver 26 of 286 name pin type function wrb / rwb r7 input write-read bar/read-write bar. this active-low signal along with csb qualifies write access to one of the DS26518 registers. data at d[7:0] is written into the addressed register at the rising edge of wrb while csb is low. intb r9 output, tri- stateable interrupt bar. this active-low output is asserted when an unmasked interrupt event is detected. intb will be deasserted (and tri-stated) when all interrupts have been acknowledged and serviced. extensive mask bits are provided at the global level, framer, liu, and bert level. spi_sel/ al/rsigf/flos1 c3 input with internal pulldown/ output spi serial bus mode select/analog loss/receive signaling freeze/framer los spi_sel: 0 = parallel bus mode, 1 = spi serial bus mode al/rsigf/flos1: analog los reflects the loss of signal detected by the liu front-end; framer los is los detection by the corresponding framer. the same pins can reflect receive-signaling freeze indications. this selection can be made by settings in global transceiver control register ( gtcr1 ). al/rsigf/flos1 are available by setting the gtcr1 .528md bit to 1. bts m13 input bus type select. set high to select mo torola bus timing, low to select intel bus timing. this pin controls the function of the rdb/dsb and wrb pins. note: if spi mode is selected by the spi_sel pin, this pin must be tied low. system interface mclk b7 input master clock. this is an independent free-running clock whose input can be a multiple of 2.048mhz 50ppm or 1.544m hz 50ppm. the clock selection is available by bits mps0 and mps1 and freqsel. multiple of 2.048mhz can be internally adapted to 1.544mhz. mult iple of 1.544mhz can be adapted to 2.048mhz. note that tclkn must be 2.048mhz for e1 and 1.544mhz for t1/j1 operation. see table 10-12 . resetb j12 input reset bar. active-low reset. this input forces the complete DS26518 reset. this includes reset of the registers, framers, and lius. refclkio a7 input/ output reference clock input/output input: a 2.048mhz or 1.544mhz clock input. this clock can be used to generate the backplane clock. this allows for the users to synchronize the system backplane with the reference clock. the other options for the backplane clock reference are liu-received clocks or mclk. output: this signal can also be used to output a 1.544mhz or 2.048mhz reference clock. this allows for multiple DS26518s to share the same reference for generation of the backplane clock. henc e, in a system consisting of multiple DS26518s, one can be a master and others a slave using the same reference clock. test digioen d8 input, pullup digital enable. when this pin and jtrst are pulled low, all digital i/o pins are placed in a high-impedance state. if this pin is high the digital i/o pins operate normally. this pin must be connected to v dd for normal operation. jtrst l5 input, pullup jtag reset. jtrst is used to asynchronously reset the test access port controller. after power-up, jtrst must be toggled from low to high. this action sets the device into the jtag device id mode. pulling jtrst low restores normal device operation. jtrst is pulled high internally via a 10k resistor operation. if boundary scan is not used, this pin should be held low. jtms k4 input, pullup jtag mode select. this pin is sampled on the rising edge of jtclk and is used to place the test access port into the va rious defined ieee 1149.1 states. this pin has a 10k pullup resistor. jtclk f5 input jtag clock. this signal is used to shift data into jtdi on the rising edge and out of jtdo on the falling edge. jtdi h4 input, pullup jtag data in. test instructions and data are clocked into this pin on the rising edge of jtclk. this pin has a 10k pullup resistor. jtdo j4 output, high impedance jtag data out. test instructions and data are cl ocked out of this pin on the falling edge of jtclk. if not used, this pin should be left unconnected.
DS26518 8-port t1/e1/j1 transceiver 27 of 286 name pin type function scanmode h13 input scan mode. when low, normal operational clocks are used to clock the flip flops. user should tie low. power supplies atvdd b1, b16, g1, g16, k1, k16, r1, r16 ? 3.3v 5% analog transmit power supply . these v dd inputs are used for the transmit liu sections of the DS26518. atvss b2, b15, g2, g15, k2, k15, r2, r15 ? analog transmit v ss . these pins are used for transmit analog v ss . arvdd d1, d16, e1, e16, m1, m16, n1, n16 ? 3.3v 5% analog receive power supply . these v dd inputs are used for the receive liu sections of the DS26518. arvss d2, d15, e2, e15, m2, m15, n2, n15 ? analog receive v ss . these pins are used for analog v ss for the receivers. acvdd h7 ? 1.8v 5% analog clock conversion v dd . this v dd input is used for the clock conversion unit (clad) of the DS26518. acvss j7 ? analog clock v ss . this pin is used for clock converter analog v ss . dvdd33 g5, g6, g11, g12, h5, h6, h8, h9, h10, h11 ? 3.3v 5% power supply for i/os dvdd18 g7?g10 ? 1.8v 5% power supply for internal v dd dvss h12, j6, j8?j11, k5?k12 ? digital ground
DS26518 8-port t1/e1/j1 transceiver 28 of 286 9. functional description 9.1 processor interface microprocessor control of the DS26518 is accomplished through the 28 hardware pins of the microprocessor port. the 8-bit parallel data bus can be configured for intel or motorola modes of operation with the bus type select (bts) pin. when the bts pin is a logic 0, bus timing is in intel mode, as shown in figure 13-2 and figure 13-3 . when the bts pin is a logic 1, bus timing is in motorola mode, as shown in figure 13-4 and figure 13-5 . the address space is mapped through the use of 13 address lines, a[12:0]. multiplexed mode is not supported on the processor interface. the chip-select bar ( csb ) pin must be brought to a logic-low level to gain read and write access to the microprocessor port. with intel timing selected, the read-data bar ( rdb ) and write-read bar ( wrb ) pins are used to indicate read and write operations and latch data through t he interface. with motorola timing selected, the read- write bar ( rwb ) pin is used to indicate read and write operations while the data-strobe bar ( dsb ) pin is used to latch data through the interface. the interrupt output pin ( intb ) is an open-drain output that asserts a logic-low level upon a number of software maskable interrupt conditions. this pin is normally connected to the microprocessor interrupt input. 9.1.1 spi serial port mode the external processor bus can be configured to operate in spi serial bus mode. see section 9.1.2 for detailed timing diagrams. when spi_sel = 1, spi bus mode is implemented using fo ur signals: clock (spi_sclk) , master out-slave in data (spi_mosi), master in-slave out data (spi_miso), and chip select ( csb ). clock polarity and phase can be set by the d[7]/spi_cpol and d[6]/spi_cpha pins. the order of the address and data bits in the serial stream is selectable us ing the d[5]/spi_swap pin. the r/w bit is always first and b bit is always last in the initial control word and are not effe cted by the d[5]/spi_swap pin setting. spi mode is not recommended for hdlc operations because of the bandwidth constraints of spi. 9.1.2 spi functional timing diagrams note: the transmit and receive order of the address and data bits are selected by the d[5]/spi_swap pin. the r/w (read/write) msb bit and b (burst) lsb bit position is not affected by the d[5]/spi_swap pin setting. 9.1.2.1 spi transmission format and cpha polarity when spi_cpha = 0, csb may be deasserted between accesses. an access is defined as one or two control bytes followed by a data byte. csb cannot be deasserted between the contro l bytes, or between the last control byte and the data byte. when spi_cpha = 0, csb may also remain asserted between accesses. if it remains asserted and the burst bit is set, no additional control by tes are expected after the first control byte(s) and data are transferred. if the burst bit is set, the address will be incremented for each additional byte of data transferred until csb is deasserted. if csb remains asserted and the burst bit is not set, a control byte(s) is expected following the data byte, and the address for the next access will be received from that. anytime csb is deasserted, the burst access is terminated. when spi_cpha = 1, csb may remain asserted for more than one access without being toggled high and then low again between accesses. if the burst bit is set, t he address should increment and no additional control bytes are expected. if the burst bit is not set, each data byte will be followed by the control byte(s ) for the next access. additionally, csb may also be deasserted between accesses when spi_cpha = 1. in the case, any burst access is terminated and the next byte received when csb is reasserted will be a control byte. the following diagrams describe the functionality of t he spi port for the four combinations of spi_cpol and spi_cpha. they indicate the clock edge that samples t he data and the level of the clock during no-transfer events (high or low). since the spi port of the DS26518 acts as a slave device, the master devic e provides the clock. the
DS26518 8-port t1/e1/j1 transceiver 29 of 286 user must configure the spi_cpol and spi_cpha pins to describe which type of clock that the master device is providing. figure 9-1. spi serial port access for r ead mode, spi_cpol = 0, spi_cpha = 0 1 a7 a13 a12 a11 a10 a9 a8 d7 d6 d5 d4 d3 d2 d1 d0 lsb msb lsb msb spi_sclk c sb spi_mosi spi_miso b a6 a5 a4 a3 a2 a1 lsb msb a0 figure 9-2. spi serial port access for r ead mode, spi_cpol = 1, spi_cpha = 0 spi_sclk 1 a7 a13 a12 a11 a10 a9 a8 d7 d6 d5 d4 d3 d2 d1 d0 lsb msb lsb msb spi_mosi spi_miso b a6 a5 a4 a3 a2 a1 lsb msb a0 c sb figure 9-3. spi serial port access for r ead mode, spi_cpol = 0, spi_cpha = 1 spi_sclk c s b 1 a 7 a 13 a 12 a 11 a 10 a 9 a 8 d7 d6 d5 d4 d3 d2 d1 d0 lsb msb lsb msb spi_mosi spi_miso b a 6 a 5 a 4 a 3 a 2 a 1 lsb msb a 0 figure 9-4. spi serial port access for r ead mode, spi_cpol = 1, spi_cpha = 1 spi_slck c s b 1 a 7 a 13 a 12 a 11 a 10 a 9 a 8 d7 d6 d5 d4 d3 d2 d1 d0 lsb msb lsb msb spi_mosi spi_miso b a 6 a 5 a 4 a 3 a 2 a 1 lsb msb a 0
DS26518 8-port t1/e1/j1 transceiver 30 of 286 figure 9-5. spi serial port access for write mode, spi_cpol = 0, spi_cpha = 0 0 a 13 lsb msb spi_sclk c s b spi_mosi spi_miso d7 d6 d5 d4 d3 d2 d1 d0 lsb msb a 4 a 3 a 2 a 1 a 0 lsb msb a 12 a 11 a 10 a 9 a 8 a 7 a 6 a 5 b figure 9-6. spi serial port access for write mode, spi_cpol = 1, spi_cpha = 0 spi_sclk c s b 0 a 13 lsb msb spi_mosi spi_miso d7 d6 d5 d4 d3 d2 d1 d0 lsb msb a 4 a 3 a 2 a 1 a 0 lsb msb a 12 a 11 a 10 a 9 a 8 a 7 a 6 a 5 b figure 9-7. spi serial port access for write mode, spi_cpol = 0, spi_cpha = 1 spi_scl k c s b 0 a 13 lsb msb spi_mosi spi_miso d7 d6 d5 d4 d3 d2 d1 d0 lsb msb a 4 a 3 a 2 a 1 a 0 lsb msb a 12 a 11 a 10 a 9 a 8 a 7 a 6 a 5 b figure 9-8. spi serial port access for write mode, spi_cpol = 1, spi_cpha = 1 spi_sclk c s b 0 a 13 lsb msb spi_mosi spi_miso d7 d6 d5 d4 d3 d2 d1 d0 lsb msb a 4 a 3 a 2 a 1 a 0 lsb msb a 12 a 11 a 10 a 9 a 8 a 7 a 6 a 5 b
DS26518 8-port t1/e1/j1 transceiver 31 of 286 9.2 clock structure the user should provide a system clock to the mclk input of 2.048mhz, 1.544mhz , or a multiple of up to 8x the t1 and e1 frequencies. to meet many specifications , the mclk source should have 50ppm accuracy. 9.2.1 backplane clock generation the DS26518 provides facility for pr ovision of bpclk1 at 2.048mhz, 4. 096mhz, 8.192mhz, 16.384mhz (see figure 9-9 ). the global transceiver cl ock control register 1 ( gtccr1 ) is used to control the backplane clock generation. this register is also used to program refclkio as an input or output. refclkio can be an output sourcing mclkt1 or mclke1 as shown in figure 9-9 . this backplane clock and frame pulse (tssyncion ) can be used by the ds265 18 and other ibo-equipped devices as an ?ibo bus master.? hence, the DS26518 pr ovides the 8khz sync pulse and 4mhz, 8mhz, and 16mhz clock. this can be used by the link layer dev ices and frames connected to the ibo bus. figure 9-9. backplane clock generation clock multiplexor rclk3 rclk4 rclk5 rclk6 rclk7 rclk1 rclk2 pre scaler pll mclkt1 mclke1 mclk bprefsel3:0 clk gen refclkio refclkio bpclk bpclk1:0 bfreqsel tssyncio rclk8 the reference clock for the backplane clock generator can be as follows: ? external master clock. a prescaler can be used to generate t1 or e1 frequency. ? external reference clock refclkio. this allows fo r multiple DS26518s to use the backplane clock from a common reference. ? internal liu recovered rclks 1 to 8. ? the clock generator can be used to generate bpc lk1 of 2.048mhz, 4.096mhz, 8.192mhz, or 16.384mhz for the ibo. ? if mclk or rclkn is used as a reference, refclkio can be used to provide a 2.048mhz or 1.544mhz clock for external use.
DS26518 8-port t1/e1/j1 transceiver 32 of 286 9.2.2 clko output clock generation this clock output is derived fr om mclk based upon the setting of the clkosel[2:0] bits in the gtccr3 register.the reference for the pll is not the input cloc k on mclk, but the scaled version of mclk (1.544mhz or 2.048mhz). the ltrcr .t1j1e1s bit also selects the proper pll for use in generating the appropriate frequency. this clock output pin is provided as an additional f eature to eliminate the need for another board oscillator. table 9-1. clko fr equency selection clkosel[3:0] clko (khz) 0000 2048 0001 4096 0010 8192 0011 16384 0100 1544 0101 3088 0110 6176 0111 12352 1000 1536 1001 3072 1010 6144 1011 12288 1100 32 1101 64 1110 128 1111 256
DS26518 8-port t1/e1/j1 transceiver 33 of 286 9.3 resets and power-down modes a hardware reset is issued by forcing the resetb pin to logic low. the resetb input pin resets all framers, lius, and berts. note that not all registers are cleared to 00h on a reset condition. the register space must be reinitialized to appropriate values after a hardware or software reset has occurred. this includes writing reserved locations to 00h. table 9-2. reset functions reset function location comments hardware device reset resetb pin transition to a logic 0 level resets the DS26518. hardware jtag reset jtrst pin resets the jtag test port. global software reset gsrr1 writing to this register resets the framers, lius and berts (transmit and receive). framer receive reset rmmr .1 writing to this bit resets the receive framer. framer transmit reset tmmr .1 writing to this bit resets the transmit framer. hdlc receive reset rhc .6 writing to this bit resets the receive hdlc controller. hdlc transmit reset thc1 .5 writing to this bit resets the transmit hdlc controller. elastic store receive reset rescr .2 writing to this bit resets the receive elastic store. elastic store transmit reset tescr .2 writing to this bit resets the transmit elastic store. bit oriented code receive reset t1rbocc .7 writing to this bit resets the receive boc controller. loop code integration reset t1rdncd1 , t1rupcd1 writing to these registers resets the programmable in-band code integration period. spare code integration reset t1rscd1 writing to this register resets the programmable in-band code integration period. the DS26518 has several features included to reduce power consumption. the individual liu transmitters can be powered down by setting the tpde bit in the liu maintenance control register ( lmcr ). note that powering down the transmit liu results in a high-impedance state for the corresponding ttipn and tringn pins and reduced operating current. the rpde in the lmcr register can be used to power down the liu receiver. the te (transmit enable) bit in the lmcr register can be used to disable the ttipn and tringn outputs and place them in a high-impedance mode, while keeping the liu in an active state (powered up). this is useful for equipment protection-switching applications.
DS26518 8-port t1/e1/j1 transceiver 34 of 286 9.4 initialization and configuration 9.4.1 example device initialization and sequence step 1: reset the device by pulling the resetb pin low, applying power to the device, or by using the software reset bits outlined in section 9.2.2 . clear all reset bits. allow time for the reset recovery. step 2: check the device id in the idr register. step 3: write the gtccr1 register to correctly configure the system clocks. if supplying a 1.544mhz mclk follows this write with at least a 300ns delay in order to allow the clock system to properly adjust. step 4: write the entire remainder of the register spac e for each port with 00h, including reserved register locations. step 5: choose t1/j1 or e1 operation for the framers by configuring the t1/e1 bit in the tmmr and rmmr registers for each framer. set the frm_en bit to 1 in the tmmr and rmmr registers. if using software transmit signaling in e1 mode, program the e1taf and e1tnaf registers as required. conf igure the framer transmit control registers ( tcr1 ? tcr4 ). configure the framer re ceive control registers ( rcr1 ? rcr3 ). configure other framer features as appropriate. step 6: choose t1/j1 or e1 operation for the lius by configuring the t1j1e1s bit in the ltrcr register. configure the line build-out for each liu. configure other liu features as appropriate. set the te (transmit enable) bit to turn on the ttipn and tringn outputs. step 7: configure the elastic stores, hdlc controller, and bert as needed. step 8: set the init_done bit in the tmmr and rmmr registers for each framer. 9.5 global resources all eight framers share a common microprocessor po rt and a common mclk. there is a common software configurable bpclk1 output. a set of global registers incl udes global resets, global interrupt status, interrupt masking, clock configuration, and the device id register. see the global register bit map in table 10-6 . a common jtag controller is used for all ports. 9.6 per-port resources each port has an associated framer, liu, bert, jitter att enuator, and transmit/receive hdlc controller. each of the per-port functions has its own register space. 9.7 device interrupts figure 9-10 diagrams the flow of interrupt conditions from their source status bits throug h the multiple levels of information registers and mask bits to the interrupt pi n. when an interrupt occurs, the host can read the global interrupt information registers gfisr1 , glisr1 , and gbisr1 to quickly identify which of the eight transceivers is (are) causing the interrupt(s). the host can then read the specific transceiver?s interru pt information registers ( tiir , riir ) and the latched status registers ( llsr , blsr ) to further identify the source of the interrupt(s). if tiir or riir is the source, the host reads the transmit latched status or the receive latched status registers for the source of the interrupt. all interrupt information regist er bits are real-time bits that clear once the appropriate interrupt has been serviced and cleared, as long as no additional, unmasked interrupt condition is present in the associated status register. all latched status bits must be cleared by the host writing a ?1? to the bit location of the interrupt condition that has been serviced. latc hed status bits that have been masked via the interrupt mask registers are masked from the interrupt information registers. the interrupt mask register bits prevent indi vidual latched status conditions from generating an interrupt, but they do not prevent the latched status bits from being set. therefore, when servicing interrupts, the user should xor the latched status with the associated interrupt mask in order to exclude bits for which the user wished to prevent interrupt service. th is architecture allows the application host to periodically poll the latched status bits for noninterrupt conditions, while using only one set of registers.
DS26518 8-port t1/e1/j1 transceiver 35 of 286 figure 9-10. device interrupt information flow diagram receive remote alarm indication clear 7 receive alarm condition clear 6 receive loss of signal clear 5 receive loss of frame clear 4 receive remote alarm indication 3 receive alarm condition 2 receive loss of signal 1 receive loss of frame 0 rls1 rim1 receive signal all ones 3 receive signal all zeros 2 receive crc4 multiframe 1 receive align frame 0 rls 2 rim2 loss of receive clk clear / loss of receive clk clear 7 spare code detected condition clear / - 6 loop down code clear / v52 link clear 5 loop up code clear / receive distant mf alarm clear 4 loss of receive clk / loss of receive clk 3 spare code detect / - 2 loop down detect / v52 link detect 1 loop up detect / receive distant mf alarm detect 0 rls3 rim3 receive elastic store full 7 receive elastic store empty 6 receive elastic store slip 5 receive signaling change of state (enable in rscse1-4 ) 3 one second timer 2 timer 1 receive multiframe 0 rls4 rim4 receive fifo overrun 5 receive hdlc opening byte 4 receive packet end 3 receive packet start 2 receive packet high watermark 1 receive fifo not empty 0 rls5 rim5 receive rai-ci 5 receive ais-ci 4 receive slc-96 alignment 3 receive fdl register full 2 receive boc clear 1 receive boc 0 rls7 rim7 transmit elastic store full 7 transmit elastic store empty 6 transmit elastic store slip 5 transmit slc96 multiframe 4 transmit align frame 3 transmit multiframe 2 loss of transmit clock clear 1 loss of transmit clock 0 tls1 tim1 transmit fdl register empty 4 transmit fifo underrun 3 transmit message end 2 transmit fifo below low watermark 1 transmit fifo not full set 0 tls2 tim2 - - - - loss of frame 1 loss of frame synchronization 0 tls3 tim3 jitter attenuator limit trip clear 7 open circuit detect clear 6 short circuit detect clear 5 loss of signal detect clear 4 jitter attenuator limit trip 3 open circuit detect 2 short circuit detect 1 loss of signal detect 0 llsr lsimr bert bit error detected 6 bert bit counter overflow 5 bert error counter overflow 4 bert receive all ones 3 bert receive all zeros 2 bert receive loss of synchronization 1 bert in synchronization 0 blsr bsim interrupt pin 0 1 2 3 4 5 riir 2 1 0 tiir 7 6 5 4 3 2 1 0 gfisr1 gfimr1 7 6 5 4 3 2 1 0 glisr1 glimr1 7 6 5 4 3 2 1 0 gbisr1 gbimr1 gtcr1.0 framers 2-8 lius 2-8 berts 2-8 drawing legend: interrupt status registers register name interrupt mask registers register name
DS26518 8-port t1/e1/j1 transceiver 36 of 286 9.8 system backplane interface the DS26518 provides a versatile backplane interface that can be configured to: ? transmit and receive two-frame elastic stores ? mapping of t1 channels into a 2.048mhz backplane ? ibo mode for multiple framers to share the backplane signals ? transmit and receive channel blocking capability ? fractional t1/e1/j1 support ? hardware-based (through the backplane interface) or processor-based signaling ? flexible backplane clock providing frequencies of 2.048mhz, 4.096mhz, 8.192mhz, 16.384mhz ? backplane clock and frame pulse (tssyncion) generator 9.8.1 elastic stores the DS26518 contains dual, two-frame elastic stores for each framer: one for the receive direction and one for the transmit direction. both elastic stores are fully indepe ndent. the transmit- and receive-side elastic stores can be enabled/disabled independently of each other. also, the transmit or receive elastic store can interface to either a 1.544mhz or 2.048/4.096/8.192/16. 384mhz backplane without regard to the backplane rate for the other elastic store. all eight channels ha ve their own tsysclkn/rsysclkn pins, allo wing a unique backplane system clock for each channel. this allows for maximum flexibility in the design of the bac kplane clock structure. the elastic stores have two main purposes. first, they can be used for rate conversion. when the DS26518 is in the t1 mode, the elastic stores can rate convert the t1 data stream to a 2.048mhz backplane. in e1 mode the elastic store can rate convert the e1 data stream to a 1.544mhz backplane. second, t hey can be used to absorb the differences in phase and frequency between the t1 or e1 clock and an asynchronous (i.e., not locked) backplane clock, which can be 1.544mhz or 2.048mhz. if the two clocks are not frequency locked, the elastic stores manage the rate difference and perform controlled s lips, deleting or repeating frames of data in order to manage the difference between the network and the backplane. if the elastic store is enabled while in e1 mode, then eit her cas or crc4 multiframe boundaries are indicated via the rmsyncn output as controlle d by the rsms2 control bit ( riocr .1). if the user selects to apply a 1.544mhz clock to the rsysclkn pin, the receive blank channel select registers ( rbcs1 ?4) determine which channels of the received e1 data stream will be deleted. in this mode an f-bit location is inserted into the rsern data and set to one. also, in 1.544mhz applications, the rchblkn output will not be active in channels 25 to 32 (or in other words, rcbr4 is not active). if the two- frame elastic buffer either fills or empt ies, a controlled slip will occur. if the buffer empties, then a full frame of data will be repeated at rsern and the rls4 .5 and rls4 .6 bits will be set to a one. if the buffer fills, then a full frame of data will be deleted and the rls4 .5 and rls4 .7 bits will be set to a one. the elastic stores can also be used to multiplex t1 or e1 data streams into higher backplane rates. this is the interleave bus option (ibo), which is discussed in section 9.8.2 . table 9-3 shows the registers related to the elastic stores. table 9-3. registers rela ted to the elastic store register framer 1 addresses function receive i/o configuration register ( riocr ) 084h sync and clock selection for the receiver. receive elastic store control register ( rescr ) 085h receive elastic store control. receive latched status register 4 ( rls4 ) 093h receive elastic store empty full status. receive interrupt mask register 4( rim4 ) 0a3h receive interrupt mask for elastic store. transmit elastic store control register ( tescr ) 185h transmit elastic control such as minimum mode. transmit latched status register 1 ( tls1 ) 190h transmit elastic store latched status. transmit interrupt mask register 1 ( tim1 ) 1a0h transmit elastic store interrupt mask. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 37 of 286 9.8.1.1 elastic stores initialization there are two elastic store initializations that may be used to improve performance in certain applications: elastic store reset and elastic store align. both of these involv e the manipulation of the elastic store?s read and write pointers and are useful primarily in synchro nous applications (rsysclkn/tsysclkn are locked to rclkn/tclkn, respectively). the elasti c store reset is used to minimize the delay through the elastic store. the elastic store align bit is used to center the read/write pointers to the extent possible. table 9-4. elastic store delay after initialization initialization register bit delay receive elastic store reset rescr .2 n bytes < delay < 1 frame + n bytes transmit elastic store reset tescr .2 n bytes < delay < 1 frame + n bytes receive elastic store align rescr .3 1/2 frame < delay < 1 1/2 frames transmit elastic store align tescr .3 1/2 frame < delay < 1 1/2 frames n = 9 for rszs = 0; n = 2 for rszs = 1 9.8.1.2 minimum delay mode elastic store minimum delay mode may be used when the elas tic store?s system clock is locked to its network clock (i.e., rclkn locked to rsysclkn for the receive side and tclkn locked to tsysclkn for the transmit side). rescr .1 enables the receive elastic store minimum delay mode. when enabled, the elastic stores will be forced to a maximum depth of 32 bits instead of the normal two-frame depth. this feature is useful primarily in applications that interface to a 2.048mhz bus. certain restrictions a pply when minimum delay mode is used. in addition to the restriction mentioned above, rsyncn must be configured as an output when the receive elastic store is in minimum delay mode, and tsyncn must be configured as an output when transmit minimum delay mode is enabled. in this mode, the sync outputs are always in frame mode (multiframe outputs are not allowed). in a typical application rsysclkn and tsysclkn are locked to rclkn, and rsyncn (frame output mode) is connected to tssyncion (frame input mode ). the slip zone select bit (rszs at rescr .4) must be set to 1. all the slip contention logic in the framer is disabled (since slips cannot oc cur). on power-up after the rsysclkn and tsysclkn signals have locked to their respective netwo rk clock signals, the elastic store reset bit ( rescr .2) should be toggled from a zero to a one to ensure proper operation. 9.8.1.3 additional receive elastic store information if the receive-side elastic store is enabled, then the user must provide either a 1.544mhz or 2.048mhz clock at the rsysclkn pin. see section 9.8.2 for higher rate system clock applicatio ns. the user has the option of either providing a frame/multiframe sync at the rsyncn pin or having the rsyncn pin provide a pulse on frame/multiframe boundaries. if signaling reinsertion is enabl ed, the robbed-bit signaling data is realigned to the multiframe sync input on rsyncn. otherwise, a multiframe sync input on rsyncn is treated as a simple frame boundary by the elastic store. the framer will always indi cate frame boundaries on the network side of the elastic store via the rfsyncn output whether the elastic store is enabled or not. multiframe boundaries will always be indicated via the rmsyncn output. if the elastic store is enabled, then rmsyncn will output the multiframe boundary on the backplane side of the elastic store. when the device is receiving t1 and the backplane is enabled for 2.048mhz operation, the rmsyncn signal will output the t1 multiframe boundaries as delayed through the elastic store. when the device is receiving e1 and the backplane is enabled for 1.544mhz operation, the rmsyncn signal will output the e1 multiframe bound aries as delayed through the elastic store. if the user selects to apply a 2.048mhz clock to the rsysclkn pin, the user can use the back plane blank channel select registers ( rbcs1 ?4) to determine which channels will have the data output at rsern forced to all ones.
DS26518 8-port t1/e1/j1 transceiver 38 of 286 9.8.1.4 receiving mapped t1 channels from a 2.048mhz backplane setting the tsclkm bit in tiocr .4 enables the transmit elastic store to operate with a 2.048mhz backplane (32 time slots / frame). in this mode the user can choose which of the backplane channels on tsern will be mapped into the t1 data stream by programming th e transmit blank channel select registers ( tbcs1 ?4). a logic 1 in the associated bit location forces the transmit elastic store to ignore backplane data for that channel. typically the user will want to program eight channels to be ignored. the def ault (power-up) configuration will ignore channels 25?32, so that the first 24 backplane channels are mapped into the t1 transmit data stream. for example, if the user desired to transmit data fr om the 2.048mhz backplane channels 2?16 and 18?26, the tbcs registers should be programmed as follows: tbcs1 = 01h :: ignore backplane channel 1 :: tbcs2 = 00h tbcs3 = 01h :: ignore backplane channel 17 :: tbcs4 = fch :: ignore backplane channels 27?32 :: 9.8.1.5 mapping t1 channels onto a 2.048mhz backplane setting the rsclkm bit in riocr .4 will enable the receive elastic store to operate with a 2.048mhz backplane (32 time slots/frame). in this mode the user can choose which of the backplane channels on rsern receive the t1 data by programming the receive blank channel select registers ( rbcs1 ?4). a logic 1 in the associated bit location will force rsern high for that backplane channel. ty pically the user will want to program eight channels to be blanked. the default (power-up) conf iguration will blank channels 25 to 32, so that the 24 t1 channels are mapped into the first 24 channels of the 2.048mhz backplane. if the user chooses to blank channel 1 (ts0) by setting rbcs1 .0 = 1, then the f-bit will be pass ed into the msb of ts0 on rsern. for example, if: rbcs1 = 01h rbcs2 = 00h rbcs3 = 01h rbcs4 = fch then on rsern: channel 1 (msb) = f-bit channel 1 (bits 1-7) = all ones channels 2-16 = t1 channels 1-15 channel 17 = all ones channels 18-26 = t1 channels 16-24 channels 27-32 = all ones note that when two or more sequential channels are chosen to be blanked, the receive slip zone select bit should be set to zero. if the blank channels are distributed (such as 1, 5, 9, 13, 17, 21, 25, 29), the rszs bit can be set to one, which can provide a lower occurrence of slips in certain applications. if the two-frame elastic buffer either fills or empties, a controlled slip will oc cur. if the buffer empties, then a full frame of data will be repeated at rsern and the rls4 .5 and rls4 .6 bits will be set to a one. if the buffer fills, then a full frame of data will be deleted and the rls4 .5 and rls4 .7 bits will be set to a one. 9.8.1.6 receiving mapped e1 transmit channels from a 1.544mhz backplane the user can use the tsclkm bit in tiocr .4 to enable the transmit elastic store to operate with a 1.544mhz backplane (24 channels / frame + f-bit). in this mode the us er can choose which of the e1 time slots will have all- ones data inserted by programming the tran smit blank channel select registers ( tbcs1 ?4). a logic 1 in the associated bit location will cause the elastic store to force all ones at the outgoing e1 data for that channel. typically the user will want to program eight channels to be blanked. the default (power-u p) configuration will blank channels 25 to 32, so that the first 24 e1 channels ar e mapped from the 24 channels of the 1.544mhz backplane.
DS26518 8-port t1/e1/j1 transceiver 39 of 286 9.8.1.7 mapping e1 channels onto a 1.544mhz backplane the user can use the rsclkm bit in riocr .4 to enable the receive elastic st ore to operate with a 1.544mhz backplane (24 channels / frame + f-bit). in this mode the user can choose which of the e1 time slots will be ignored (not transmitted onto rsern) by programm ing the receive blank channel select registers ( rbcs1 ?4). a logic 1 in the associated bit location will cause the elas tic store to ignore the incoming e1 data for that channel. typically, the user will want to prog ram eight channels to be ignored. the de fault (power-up) configuration will ignore channels 25 to 32, so that the first 24 e1 c hannels are mapped into the 24 channels of the 1.544mhz backplane. in this mode the f-bit locati on at rsern is always set to 1. for example, if the user wants to ignore e1 time slots 0 (channel 1) and ts 16 (cha nnel 17), the rbcs registers would be programmed as follows: rbcs1 = 01h rbcs2 = 00h rbcs3 = 01h rbcs4 = fch 9.8.2 ibo multiplexing the DS26518 offers two methods of multiplexing data streams onto a high-speed backplane bus. the traditional method of ibo operation that allows the user to gang si gnals together on the pcb is supported. rsern and rsign will tri-state at the appropriate times to a llow the ganging of these signals together. the default method multiplexes the data streams interna lly and then outputs them on one pin, i.e., rser1. for example, if the user wants to multiplex rser[1:8] together to make a 16mhz high-speed bus, the data stream will be output on rser1 only. the selection between external ganging and internal multiplexing is made via gtcr1 . gibo. note that in ibo mode, the channel block signals tchb lkn and rchblkn ar e referenced to as tsysclkn and rsysclkn. figure 9-11 , figure 9-12 , and figure 9-13 show the equivalent internal circuit for each ibo mode. these figures only show channels 1?8. table 9-5 describes the pin function changes for each mode of the ibo multiplexer. table 9-5. registers relate d to the ibo multiplexer register framer 1 addresses function global transceiver control register 1 ( gtcr1 ) 00f0h this is a global register used to specify ganged operation for the ibo. global framer control register 1 ( gfcr1 ) 00f1h this global register defines the number of devices per bus and bus speed. receive interleave bus operation control register ( riboc ) 088h this register configures the per-port ibo enable and type of interleaving (channel vs. frame). transmit interleave bus operation control register ( tiboc ) 188h this register configures the per-port ibo enable and type of interleaving (channel vs. frame). note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 40 of 286 DS26518 8-port t1/e1/j1 transceiver figure 9-11. ibo multiplexer equivalent circuit?4.096mhz figure 9-11. ibo multiplexer equivalent circuit?4.096mhz rser rsig rsync rsysclk tser tsig tssync tsysclk port # 1 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 2 backplane interface ribo_oeb rser1 rsig1 rsync1 rsysclk1 tser1 tsig1 tssyncio1 tsysclk1 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 3 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 4 backplane interface ribo_oeb rser3 rsig3 rsync3 rsysclk3 tser3 tsig3 tssyncio3 tsysclk3 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 5 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 6 backplane interface ribo_oeb rser5 rsig5 rsync5 rsysclk5 tser5 tsig5 tssyncio5 tsysclk5 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 7 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 8 backplane interface ribo_oeb rser7 rsig7 rsync7 rsysclk7 tser7 tsig7 tssyncio7 tsysclk7 40 of 286 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 1 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 2 backplane interface ribo_oeb rser1 rsig1 rsync1 rsysclk1 tser1 tsig1 tssyncio1 tsysclk1 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 3 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 4 backplane interface ribo_oeb rser3 rsig3 rsync3 rsysclk3 tser3 tsig3 tssyncio3 tsysclk3 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 5 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 6 backplane interface ribo_oeb rser5 rsig5 rsync5 rsysclk5 tser5 tsig5 tssyncio5 tsysclk5 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 7 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 8 backplane interface ribo_oeb rser7 rsig7 rsync7 rsysclk7 tser7 tsig7 tssyncio7 tsysclk7
DS26518 8-port t1/e1/j1 transceiver 41 of 286 figure 9-12. ibo multiplexer equivalent circuit?8.192mhz rser rsig rsync rsysclk tser tsig tssync tsysclk port # 1 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 2 backplane interface ribo_oeb rser1 rsig1 rsync1 rsysclk1 tser1 tsig1 tssyncio1 tsysclk1 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 3 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 4 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 5 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 6 backplane interface ribo_oeb rser5 rsig5 rsync5 rsysclk5 tser5 tsig5 tssyncio5 tsysclk5 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 7 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 8 backplane interface ribo_oeb
DS26518 8-port t1/e1/j1 transceiver 42 of 286 figure 9-13. ibo multiplexer equivalent circuit?16.384mhz rser rsig rsync rsysclk tser tsig tssync tsysclk port # 1 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 2 backplane interface ribo_oeb rser1 rsig1 rsync1 rsysclk1 tser1 tsig1 tssyncio1 tsysclk1 rser rsig rsync rsysclk tser tsig tssync tsysclk port # 3 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 4 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 5 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 6 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 7 backplane interface ribo_oeb rser rsig rsync rsysclk tser tsig tssync tsysclk port # 8 backplane interface ribo_oeb ribo_oeb(1-8) ribo_oeb(1-8) rser(1) rser(2) rser(3) rser(4) rser(5) rser(6) rser(7) rser(8) rsig(1) rsig(2) rsig(3) rsig(4) rsig(5) rsig(6) rsig(7) rsig(8) to mux to mux to mux to mux to mux to mux to mux to mux to mux to mux to mux to mux to mux to mux to mux
DS26518 8-port t1/e1/j1 transceiver 43 of 286 table 9-6. rsern out put pin definitions ( gtcr1 .gibo = 0) pin normal use 4.096mhz ibo 8.192mhz ibo 16.384mhz ibo rser1 receive serial data for port 1 combined receive serial data for ports 1 and 2 combined receive serial data for ports 1?4 receive serial data for ports 1?8 rser2 receive serial data for port 2 reserved unused unused rser3 receive serial data for port 3 combined receive serial data for ports 3 and 4 unused unused rser4 receive serial data for port 4 unused unused unused rser5 receive serial data for port 5 combined receive serial data for ports 5 and 6 combined receive serial data for ports 5?8 unused rser6 receive serial data for port 6 unused unused unused rser7 receive serial data for port 7 combined receive serial data for ports 7 and 8 unused unused rser8 receive serial data for port 8 unused unused unused table 9-7. rsign output pin definitions ( gtcr1 .gibo = 0) pin normal use 4.096mhz ibo 8.192mhz ibo 16.384mhz ibo rsig1 receive signaling data for port 1 combined receive signaling data for ports 1 and 2 combined receive signaling data for ports 1?4 receive signaling data for ports 1?8 rsig2 receive signaling data for port 2 unused unused unused rsig3 receive signaling data for port 3 combined receive signaling data for ports 3 and 4 unused unused rsig4 receive signaling data for port 4 unused unused unused rsig5 receive signaling data for port 5 combined receive signaling data for ports 5 and 6 combined receive signaling data for ports 5?8 unused rsig6 receive signaling data for port 6 unused unused unused rsig7 receive signaling data for port 7 combined receive signaling data for ports 7 and 8 unused unused rsig8 receive signaling data for port 8 unused unused unused
DS26518 8-port t1/e1/j1 transceiver 44 of 286 table 9-8. tsern input pin definitions ( gtcr1 .gibo = 0) pin normal use 4.096mhz ibo 8.192mhz ibo 16.384mhz ibo tser1 transmit serial data for port 1 combined transmit serial data for ports 1 and 2 combined transmit serial data for ports 1?4 transmit serial data for ports 1?8 tser2 transmit serial data for port 2 unused unused unused tser3 transmit serial data for port 3 combined transmit serial data for ports 3 and 4 unused unused tser4 transmit serial data for port 4 unused unused unused tser5 transmit serial data for port 5 combined transmit serial data for ports 5 and 6 combined transmit serial data for ports 5?8 unused tser6 transmit serial data for port 6 unused unused unused tser7 transmit serial data for port 7 combined transmit serial data for ports 7 and 8 unused unused tser8 transmit serial data for port 8 unused unused unused table 9-9. tsign input pin definitions ( gtcr1 .gibo = 0) pin normal use 4.096mhz ibo 8.192mhz ibo 16.384mhz ibo tsig1 transmit signaling data for port 1 combined transmit signaling data for ports 1 and 2 combined transmit signaling data for ports 1?4 transmit signaling data for ports 1?8 tsig2 transmit signaling data for port 2 unused unused unused tsig3 transmit signaling data for port 3 combined transmit signaling data for ports 3 and 4 unused unused tsig4 transmit signaling data for port 4 unused unused unused tsig5 transmit signaling data for port 5 combined transmit signaling data for ports 5 and 6 combined transmit signaling data for ports 5?8 unused tsig6 transmit signaling data for port 6 unused unused unused tsig7 transmit signaling data for port 7 combined transmit signaling data for ports 7 and 8 unused unused tsig8 transmit signaling data for port 8 unused unused unused
DS26518 8-port t1/e1/j1 transceiver 45 of 286 table 9-10. rsyncn i nput pin definitions ( gtcr1 .gibo = 0) pin normal use 4.096mhz ibo 8.192mhz ibo 16.384mhz ibo rsync1 receive frame pulse for port 1 receive frame pulse for ports 1 and 2 receive frame pulse for ports 1?4 receive frame pulse for ports 1?8 rsync2 receive frame pulse for port 2 unused unused unused rsync3 receive frame pulse for port 3 receive frame pulse for ports 3 and 4 unused unused rsync4 receive frame pulse for port 4 unused unused unused rsync5 receive frame pulse for port 5 receive frame pulse for ports 5 and 6 receive frame pulse for ports 5?8 unused rsync6 receive frame pulse for port 6 unused unused unused rsync7 receive frame pulse for port 7 receive frame pulse for ports 7 and 8 unused unused rsync8 receive frame pulse for port 8 unused unused unused 9.8.3 h.100 (ct bus) compatibility the h.100 (or ct bus) is a synchronous, bit-serial, td m transport bus operating at 8.192mhz. the h.100 standard also allows compatibility modes to operate at 2.048mhz, 4.096mhz, or 8.192mhz. the control bit h100en ( riocr .5), when combined with rsyncinv and tssynci nv, allows the DS26518 to accept a ct-bus- compatible frame-sync signal ( ct_frame ) at the rsyncn and tssyncion (input mode) inputs. see figure 9-14 and figure 9-15 . the following rules apply to the h100en control bit: 1) the h100en bit controls the sa mpling point for the rsyncn (i nput mode) and t ssyncion (input mode) only. the rsyncn output and other sync signals are not affected. 2) the h100en bit would always be used in conjunction with the receive and transmit elastic store buffers. 3) the h100en bit would typically be used with 8.192mhz ibo mode, but could also be used with 4.096mhz ibo mode or 2.048mhz backplane operation. 4) the h100en bit in riocr controls both rsyncn a nd tssyncion (i.e., there is no separate control bit for the tssyncion). 5) the h100en bit does not invert the expected signal; rsyncinv ( riocr ) and tssyncinv ( tiocr ) must be set high to invert the inbound sync signals.
DS26518 8-port t1/e1/j1 transceiver 46 of 286 figure 9-14. rsyncn input in h.100 (ct bus) mode bit 8 bit 1 bit 2 rsyncn 1 rsyncn 2 rsysclkn rsern t bc 3 note 1: rsyncn input mode in normal operation. note 2: rsyncn input mode, h100en = 1 and rsyncinv = 1. note 3: t bc ( bit cell time ) = 122ns ( t yp ) . t bc = 244ns or 488ns also acceptable. figure 9-15. tssyncion (input mode) input in h.100 (ct bus) mode bit 8 bit 1 bit 2 tssyncion 1 tssyncion 2 tsysclkn tsern t bc 3 note 1: tssyncion in normal operation. note 2: tssyncion with h100en = 1 and tssyncinv = 1. note 3: t bc ( bit cell time ) = 122ns ( t yp ) . t bc = 244ns or 488ns also acceptable.
DS26518 8-port t1/e1/j1 transceiver 47 of 286 9.8.4 transmit and receive channel blocking registers the receive channel blocking registers ( rcbr1 /rcbr2/rcbr3/rcbr4) and the transmit channel blocking registers ( tcbr1 /tcbr2/tcbr3/tcbr4) control the rchblkn and tchblkn pins, respectively. the rchblkn and tchblkn pins are user-programm able outputs that can be forced either high or low during individual channels. these outputs can be used to block clocks to a usart or lapd controller in isdn-pri applications. when the appropriate bits are set to a one, the rchblkn and tchblkn pins will be held high during the entire corresponding channel time. when used with a t1 (1.5 44mhz) backplane, only tcbr1 to tcbr3 will be used. tcbr4 is included to support an e1 (2.048mhz) backplane when the elastic store is configured for t1-to-e1 rate conversion (see section 9.8.1 ). 9.8.5 transmit fractional support (gapped clock mode) the DS26518 can be programmed to output gapped clocks for selected channels in the receive and transmit paths to simplify connections into a usart or lapd controller in fractional t1/e1 or isdn-pri applications. when the gapped clock feature is enabled, a gated clock is output on the tchclk signal. the channel selection is controlled via the transmit gapped clock channel select registers ( tgccs1 ?4). the transmit path is enabled for gapped clock mode with the tgclken bit ( tescr .6). both 56kbps and 64kbps channel formats are supported as determined by tescr .7. when 56kbps mode is selected, the clock corresponding to the data/control bit in the channel is omitted (only the seven most significant bits of the channel have clocks). 9.8.6 receive fractional support (gapped clock mode) the DS26518 can be programmed to output gapped clocks for selected channels in the receive and transmit paths to simplify connections into a usart or lapd controller in fractional t1/e1 or isdn-pri applications. when the gapped clock feature is enabled, a gated clock is out put on the rchclkn signal. the channel selection is controlled via the receive gapped clock channel select registers ( rgccs1 ?4). the receive path is enabled for gapped clock mode with the rgclken bit ( rescr .6). both 56kbps and 64kbps channel formats are supported as determined by rescr .7. when 56kbps mode is selected, the clock corresponding to the dat a/control bit in the channel is omitted (only the seven most significant bits of the channel have clocks).
DS26518 8-port t1/e1/j1 transceiver 48 of 286 9.9 framers the DS26518 framer cores are software selectable for t1, j1, or e1. the receive framer locates the frame and multiframe boundaries and monitors the data stream for alarms. it is also used for extracting and inserting signaling data, t1 fdl data, and e1 si- and sa-bit information. the receive-side framer decodes ami, b8zs line coding, synchronizes to the data stream, repo rts alarm information, counts frami ng/coding and crc errors, and provides clock/data and frame-sync signals to the backplane interf ace section. diagnostic capabilities include loopbacks, and 16-bit loop-up and loop-down code detection. the device contains a set of internal registers for host access and control of the device. on the transmit side, clock, data, and frame-sync signals are provided to the framer by the backplane interface section. the framer inserts the approp riate synchronization framing patterns, alarm information, calculates and inserts the crc codes, and provides the b8zs (zero code suppression) and ami line coding. both the transmit and receive path have an hdlc controller. the hdlc controller transmits and receives data via the framer block. the hdlc controller may be assigned to any time slot, portion of a time slot, or to fdl (t1). the hdlc controller has separate 64-byte tx and rx fifo to reduce the amount of processor overhead required to manage the flow of data. the backplane interface provides a versatile method of sending and receiving data from the host system. elastic stores provide a method for interfacing to asynchronous systems, converting from a t1/e1 network to a 2.048mhz, 4.096mhz, 8.192mhz or n x 64khz system backplane. the elastic stores also manage slip conditions (asynchronous interface). an ibo (inter leave bus option) is provided to allow multiple framers in the DS26518 to share a high-speed backplane. 9.9.1 t1 framing ds1 trunks contain 24 bytes of serial voice/data c hannels bundled with an overhead bit, the f-bit. the f-bit contains a fixed pattern for the receiver to delineate the frame boundaries. the f-bit is inserted once per frame at the beginning of the transmit frame boundary. the frames ar e further grouped into bundles of frames 12 for d4 and 24 for esf. the d4 and esf framing modes are outlined in table 9-11 and table 9-12 . in the d4 mode, framing bit for frame 12 is ignored if japanese yellow is selected. table 9-13 shows slc-96 framing. table 9-11. d4 framing mode frame number ft fs signaling 1 1 2 0 3 0 4 0 5 1 6 1 a 7 0 8 1 9 1 10 1 11 0 12 0 b
DS26518 8-port t1/e1/j1 transceiver 49 of 286 table 9-12. esf framing mode frame number framing fdl crc signaling 1 2 crc1 3 4 0 5 6 crc2 7 8 0 9 10 crc3 11 12 13 14 crc4 15 16 0 17 18 crc5 19 20 1 21 22 crc6 23 24 1 table 9-13. slc-96 framing frame number ft fs signaling 1 1 2 0 3 0 4 0 5 1 6 1 a 7 0 8 1 9 1 10 1 11 0 12 0 b 13 1 14 0 15 0 16 0 17 1 18 1 c 19 0 20 1 21 1 22 1 23 0 24 c1 (concentrator bit) d 25 1 26 c2 (concentrator bit) 27 0
DS26518 8-port t1/e1/j1 transceiver 50 of 286 frame number ft fs signaling 28 c3 (concentrator bit) 29 1 30 c4 (concentrator bit) a 31 0 32 c5 (concentrator bit) 33 1 34 c6 (concentrator bit) 35 0 36 c7 (concentrator bit) b 37 1 38 c8 (concentrator bit) 39 0 40 c9 (concentrator bit) 41 1 42 c10 (concentrator bit) c 43 0 44 c11 (concentrator bit) 45 1 46 0 (spoiler bit) 47 0 d 48 1 (spoiler bit) 49 1 50 0 (spoiler bit) 51 0 52 m1 (maintenance bit) 53 1 54 m2 (maintenance bit) a 55 0 56 m3 (maintenance bit) 57 1 58 a1 (alarm bit) 59 0 60 a2 (alarm bit) b 61 1 62 s1 (switch bit) 63 0 64 s2 (switch bit) 65 1 c 66 s3 (switch bit) 67 0 68 s4 (switch bit) 69 1 70 1 (spoiler bit) 71 0 72 0 d
DS26518 8-port t1/e1/j1 transceiver 51 of 286 9.9.2 e1 framing the e1 framing consists of fas, nfas detection as shown in table 9-14 . table 9-14. e1 fas/nfas framing crc-4 frame # type 1 2 3 4 5 6 7 8 0 fas c1 0 0 1 1 0 1 1 1 nfas 0 1 a sa4 sa5 sa6 sa7 sa8 2 fas c2 0 0 1 1 0 1 1 3 nfas 0 1 a sa4 sa5 sa6 sa7 sa8 4 fas c3 0 0 1 1 0 1 1 5 nfas 1 1 a sa4 sa5 sa6 sa7 sa8 6 fas c4 0 0 1 1 0 1 1 7 nfas 0 1 a sa4 sa5 sa6 sa7 sa8 8 fas c1 0 0 1 1 0 1 1 9 nfas 1 1 a sa4 sa5 sa6 sa7 sa8 10 fas c2 0 0 1 1 0 1 1 11 nfas 1 1 a sa4 sa5 sa6 sa7 sa8 12 fas c3 0 0 1 1 0 1 1 13 nfas e1 1 a sa4 sa5 sa6 sa7 sa8 14 fas c4 0 0 1 1 0 1 1 15 nfas e2 1 a sa4 sa5 sa6 sa7 sa8 c = c bits are the crc-4 remainder; a = alarm bits; sa = bits for data link.
DS26518 8-port t1/e1/j1 transceiver 52 of 286 table 9-15 shows the registers that are re lated to setting up the framing. table 9-15. registers related to setting up the framer register framer 1 addresses function transmit master mode register ( tmmr ) 180h t1/e1 mode. transmit control register 1 ( tcr1 ) 181h source of the f-bit. transmit control register 2 ( t1.tcr2 ) 182h f-bit corruption, selection of slc-96. transmit control register 3 ( tcr3 ) 183h esf or d4 mode selection. receive master mode register ( rmmr ) 080h t1/e1 selection for receiver. receive control register 1 ( rcr1 ) 081h resynchronization criteria for the framer. receive control register 2 ( t1rcr2 ) 014h t1 remote alarm and oof criteria. receive control register 2 ( e1rcr2 ) 082h e1 receive loss of signal criteria selection. receive latched status register 1 ( rls1 ) 090h receive latched status 1. receive interrupt mask register 1 ( rim1 ) 0a0h receive interrupt mask 1. receive latched status register 2 ( rls2 ) 091h receive latched status 2. receive interrupt mask register 2 ( rim2 ) 0a1h receive interrupt mask 2. receive latched status register 4 ( rls4 ) 093h receive latched status 4. receive interrupt mask register 4 ( rim4 ) 0a3h receive interrupt mask 4. frames out of sync count register 1 ( foscr1 ) 054h framer out of sync register 1. frames out of sync count register 2 ( foscr2 ) 055h framer out of sync register 2. e1 receive align frame register ( e1raf ) 064h raf byte. e1 receive non-align frame register ( e1rnaf ) 065h rnaf byte. transmit slc-96 data link register 1 ( t1tslc1 ) 164h transmit slc-96 bits. transmit slc-96 data link register 2 ( t1tslc2 ) 165h transmit slc-96 bits. transmit slc-96 data link register 3 ( t1tslc3 ) 166h transmit slc-96 bits. receive slc-96 data link register 1 ( t1rslc1 ) 064h receive slc-96 bits. receive slc-96 data link register 2 ( t1rslc2 ) 065h receive slc-96 bits. receive slc-96 data link register 3 ( t1rslc3 ) 066h receive slc-96 bits. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex); where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 53 of 286 9.9.3 t1 transmit synchronizer the DS26518 transmitter can identify the d4 or esf frame boundary, as well as the crc multiframe boundaries within the incoming nrz data stream at tsern. the tfm ( tcr3 .2) control bit determines whether the transmit synchronizer searches for the d4 or esf multiframe. a dditional control signals for the transmit synchronizer are located in the tsyncc register. the latched status bit tls3 .0 (lofd) is provided to indicate that a loss of frame synchronization has occurred, and a real-time bit (lof) wh ich is set high when the synchronizer is searching for frame/multiframe alignment. the lofd bit can be enabled to cause an interrupt condition on intb . note that when the transmit synchronizer is used, the tsyncn signal should be set as an output (tsio = 1) and the recovered frame- sync pulse will be output on this signal. the re covered crc-4 multi-frame sync pulse will be output if enabled with tiocr .0 (tsm = 1). other key points concerning the e1 transmit synchronizer: 1) the tx synchronizer is not operat ional when the transmit elastic stor e is enabled, including ibo modes. 2) the tx synchronizer does not perform crc-6 alignm ent verification (esf mode) and does not verify crc-4 codewords. the tx synchronizer cannot search for the cas multiframe. table 9-16 shows the registers related to the transmit synchronizer. table 9-16. registers related to the transmit synchronizer register framer 1 addresses function transmit synchronizer control register ( tsyncc ) 18eh resynchronization cont rol for the transmit synchronizer. transmit control register 3 ( tcr3 ) 183h tfm bit selects between d4 and esf for the transmit synchronizer. transmit latched status register 3 ( tls3 ) 192h provides latched status for the transmit synchronizer. transmit interrupt mask register 3 ( tim3 ) 1a2h provides mask bits for the tls3 status. transmit i/o configuration register ( tiocr ) 184h tsyncn should be set as an output. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex); where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 54 of 286 9.9.4 signaling the DS26518 supports both software and hardware-based signaling. interrupts can be generated on changes of signaling data. the DS26518 is also equipped with receive- signaling freeze on loss of synchronization (oof), carrier loss or change of frame alignment. the DS26518 also has hardware pins to indicate signaling freeze. features include the following: flexible signaling support: software or hardware based interrupt generated on change of signaling data receive-signaling freeze on loss of frame, loss of signal, or change of frame alignment hardware pins for carrier loss and signaling freeze indication table 9-17. registers related to signaling register framer 1 addresses function transmit-signaling registers 1 to 16 ( ts1 to ts16) 140h to 14bh (t1/j1) 140h to 14fh (e1 cas) transmit abcd signaling. software-signaling insertion enable registers 1 to 4 ( ssie1 to ssie4) 118h, 119h, 11ah, 11bh when enabled, signaling is inserted for the channel. transmit hardware-signaling channel select registers 1 to 4 ( thscs1 to thscs4) 1c8h, 1c9h, 1cah, 1cbh bits determine which channels will have signaling inserted in hardware-signaling mode. receive-signaling control register ( rsigc ) 013h freeze control for receive signaling. receive-signaling all-ones insertion registers 1 to 3 ( t1rsaoi1 to t1rsaoi3) 038h, 039h, 03ah registers for all-ones insertion (t1 mode only). receive-signaling registers 1 to 16 ( rs1 to rs16) 040h to 04bh (t1/j1) 040h to 04fh (e1) receive-signaling bytes. receive-signaling status registers 1 to 4 ( rss1 to rss4) 098h to 09ah (t1/j1) 98h to 9fh (e1) receive-signaling change of status bits. receive-signaling change of state enable registers 1 to 4 ( rscse1 to rscse4) 0a8h, 0a9h, 0aah, 0abh receive-signaling change of state interrupt enable. receive latched status register 4 ( rls4 ) 093h receive-signaling change of state bit. receive interrupt mask register 4 ( rim4 ) 0a3h receive-signaling change of state interrupt mask bit. receive-signaling reinsertion enable registers 1 to 4 ( rsi1 to rsi4) 0c8h, 0c9h, 0cah, 0cbh registers for signaling reinsertion. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex); where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 55 of 286 9.9.4.1 transmit-signaling operation there are two methods to provide transmit-signaling data. these are processor based (i.e., software based) or hardware based. processor-based refers to ac cess through the transmit signaling registers, ts1 ?ts16, while hardware based refers to using the tsign pi ns. both methods can be used simultaneously. 9.9.4.1.1 processor-based transmit signaling in processor-based mode, signaling data is l oaded into the transmit-signaling registers ( ts1 ?ts16) via the host interface. on multiframe boundaries, the contents of these registers are loaded into a shift register for placement in the appropriate bit position in the outgoing data stream. the us er can utilize the transmit multiframe interrupt in the transmit latched status register 1 ( tls1 .2) to know when to update the signaling bits. the user need not update any transmit signaling register for which there is no change of state for that register. each transmit-signaling register c ontains the robbed-bit signaling ( tcr1 .4 in t1 mode) or ts16 cas signaling ( tcr1 .6 in e1 mode) for one time slot that will be inserted into the outgoing stream. signaling data can be sourced from the ts registers on a per-chan nel basis by using the software signaling insertion enable registers, ssie1 ?4. in t1 esf framing mode, there are four signaling bits per channel (a, b, c, and d). ts1?ts12 contain a full multiframe of signaling data. in t1 d4 framing mode, ther e are only two signaling bits per channel (a and b). in t1 d4 framing mode, the framer uses a and b bit positions for the next multiframe. the c and d bit positions become ?don?t care? in d4 mode. in e1 mode, ts16 carries the signaling information. this information can be in either ccs (common channel signaling) or cas (channel associated signaling) format. the 32 time slots are referenced by two different channel number schemes in e1. in ?channel? numbering, ts0?ts31 are labeled channels 1 through 32. in ?phone channel? numbering ts1?ts15 are labeled channel 1 to channel 15 and ts17?ts31 are labeled channel 15 to channel 30. 9.9.4.1.2 time slot numbering schemes ts 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 phone channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 9.9.4.1.3 hardware-based transmit signaling in hardware-based mode, signaling data is input via the tsign pin. this signaling pcm stream is buffered and inserted to the data stream being input at the tsern pin. signaling data may be input via the transmit hardware-signaling channel select register ( thscs1 ) function. the framer can be set up to take the signaling data presented at the tsign pin and insert the signaling data into the pcm data stream that is being input at the tsern pin. the user can control which channels are to have signaling data from the tsign pin inserted into them on a per-channel basis. the signaling insert ion capabilities of the framer are available whether the transmit-side elastic store is enabled or disabled. if the elastic store is enabled, the backplane clock (tsysclkn) can be either 1.544mhz or 2.048mhz.
DS26518 8-port t1/e1/j1 transceiver 56 of 286 9.9.4.2 receive-signaling operation there are two methods to access receive-signaling data and provide transmit-signaling data: processor based (i.e., software based) or hardware based. processor-based re fers to access through the transmit- and receive-signaling registers, rs1 ?rs16. hardware based refers to the rsign pi n. both methods can be used simultaneously. 9.9.4.2.1 processor-based receive signaling signaling information is sampled from the receive data st ream and copied into the re ceive-signaling registers, rs1 ?rs16. the signaling information in these registers is always updated on mu ltiframe boundaries. this function is always enabled. 9.9.4.2.2 change of state to avoid constant monitoring of the receive-signaling r egisters, the DS26518 can be pr ogrammed to alert the host when any specific channel or channels und ergo a change of their signaling state. rscse1 ?4 are used to select which channels can cause a change of state indication. the change of state is indicated in receive latched status register 4 ( rls4 .3). if signaling integration is enabled, the ne w signaling state must be constant for three multiframes before a change of state indicati on is indicated. the user can enable the intb pin to toggle low upon detection of a change in signaling by setting the interrupt mask bit rim4 .3. the signaling integration mode is global and cannot be enabled on a channel-by-channel basis. the user can identity which channels have undergone a signaling change of state by reading the receive- signaling status registers ( rss1 ?4) . the information from these registers will tell the user which rsx register to read for the new signaling data. all changes are indi cated in the rss1?4 registers regardless of the rscse1 ?4 registers. 9.9.4.2.3 hardware-based receive signaling in hardware-based signaling the signaling data is can be obtai ned from the rsern pin or the rsign pin. rsign is a signaling pcm stream output on a channel by channel ba sis from the signaling buffer. the t1 robbed bit or e1 ts16 signaling data is still present in the original data stream at rsern. the signa ling buffer provides signaling data to the rsign pin and also allows signaling data to be reinserted into the original data stream in a different alignment that is determined by a multiframe signal from the rsyncn pin. in this mode, the receive elastic store may be enabled or disabled. if the receive elastic store is enabled, then the backpl ane clock (rsysclkn) can be either 1.544mhz or 2.048mhz. in the esf framing mode, t he abcd signaling bits are output on rsign in the lower nibble of each channel. the rsign data is updated once a multiframe (3ms for t1 esf, 1.5ms for t1 d4, 2ms for e1 cas) unless a signaling freeze is in effect. in the d4 framing mode, the ab signaling bits are output twice on rsign in the lower nibble of each channel. hence, bits 5 and 6 contain the same data as bits 7 and 8, respectively, in each channel. 9.9.4.2.4 receive-signali ng reinsertion at rsern in this mode, the user will provide a multiframe sync at the rsyncn pin and the signaling data will be reinserted based on this alignment. in t1 mode, this results in two c opies of the signaling data in the rsern data stream. the original signaling data based on the fs/esf frame posit ions and the realigned data based on the user supplied multiframe sync applied at rsyncn. in voice channels this extra copy of signaling data is of little consequence. reinsertion can be avoided in data channels since this feat ure is activated on a per-channel basis. for reinsertion, the elastic store must be enabled and for t1, the backplane clock can be either 1.544mhz or 2.048mhz. e1 signaling information cannot be reinserted into a 1.544mhz backplane. signaling reinsertion mode is enabled, on a per-channel ba sis by setting the receive-signaling reinsertion channel select bit high in the rsi1 ?4 register. the channels that are to have sig naling reinserted are selected by writing to the rsi1 ?4 registers. in e1 mode, the user will generally select all channels or none for reinsertion. 9.9.4.2.5 force receive-signaling all ones in t1 mode, the user can on a per-channel basis force the robbed-bit signaling bit positions to a one. this is done by using the receive-signaling all-ones insertion registers ( t1rsaoi1 ?3). the user sets the channel select bit in the t1rsaoi1 ?3 registers to select the channels that are to have the signaling forced to one.
DS26518 8-port t1/e1/j1 transceiver 57 of 286 9.9.4.2.6 receive-signaling freeze the signaling data in the four multiframe signaling buffers w ill be frozen in a known good state upon either a loss of synchronization (oof event), carrier loss, or change of frame alignment. in t1 mode, this action meets the requirements of bellcore tr-tsy-000170 for signaling freezi ng. to allow this freeze action to occur, the rsfe control bit ( rsigc .1) should be set high. the user can force a freeze by setting the rsff control bit ( rsigc .2) high. the rsigf output pin provides a hardware indication t hat a freeze is in effect. the four multiframe buffer provides a three multiframe delay in the signaling bits pr ovided at the rsign pin (and at the rsern pin if receive- signaling reinsertion is enabled). when freezing is enabled (rsfe = 1), the si gnaling data will be held in the last known good state until the corrupting error condition subsides. when the error condition subsides, the signaling data will be held in the old state for at least an additional 9ms (4.5ms in d4 framing mode, 6ms for e1 mode) before being allowed to be updated with new signaling data. the receive-signaling registers are fr ozen and not updated during a loss of sync condition. they will contain the most recent signaling information before the lof occurred. 9.9.4.3 transmit slc-96 operation (t1 mode only) in an slc-96-based transmission scheme, the standard fs-bit pattern is robbed to make room for a set of message fields. the slc-96 multiframe is made up of six d4 superframes, hence it is 72 frames long. in the 72- frame slc-96 multiframe, 36 of the framing bits are the normal ft pattern and the other 36 bits are divided into alarm, maintenance, spoiler, and concentrator bits as well as 12-bits of the normal fs pattern. additional slc-96 information can be found in bellcore document tr-tsy-000 008. registers related to the transmit fdl are shown in table 9-18 . table 9-18. registers related to slc-96 register framer 1 addresses function transmit fdl register ( t1tfdl ) 162h for sending messages in transmit slc-96 ft/fs bits. transmit slc-96 data link registers 1 to 3 ( t1tslc1 : t1tslc3 ) 164h, 165h, 166h registers that cont rol the slc-96 overhead values. transmit control register 2 t1.tcr2 ) 182h transmit control for data selection source for the ft/fs bits. transmit latched status register 1 ( tls1 ) 190h status bit for indicating transmission of data link buffer. receive slc-96 data link registers 1 to 3 ( t1rslc1 : t1rslc3 ) 064h, 065h, 066h ? receive latched status register 7 ( rls7 ) 096h receive slc-96 alignment event. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. the t1tfdl register is used to insert the slc-96 message fields. to insert the slc-96 message using the t1tfdl register, the user should configure the DS26518 as shown below: ? t1.tcr2 .6 (tslc96) = 1 enable transmit slc-96. ? t1.tcr2 .7 (tfdls) = 0 source fs bits via tfdl or slc-96 formatter. ? tcr3 .2 (tfm) = 1 d4 framing mode. ? tcr1 .6 (tfpt) = 0 do not ?pass through? tsern f-bits. the DS26518 will automatically insert the 12-bit alignment pattern in the fs bits for the slc-96 data link frame. data from the t1tslc1 ?3 will be inserted into the remaining fs-bit lo cations of the slc-96 mu ltiframe. the status bit tslc96 located at tls1 .4 will set to indicate that the slc-96 data link buffer has been transmitted and that the user should write new message data into t1tslc1 ?3. the host will have 9ms after the assertion of tls1 .4 to write the registers t1tslc1 ?3. if no new data is provided in these registers, the previous values will be retransmitted.
DS26518 8-port t1/e1/j1 transceiver 58 of 286 9.9.4.4 receive slc-96 operation (t1 mode only) in an slc-96-based transmission scheme, the standard fs-bit pattern is robbed to make room for a set of message fields. the slc-96 multiframe is made up of six d4 superframes, hence it is 72 frames long. in the 72- frame slc-96 multiframe, 36 of the framing bits are the normal ft pattern and the other 36-bits are divided into alarm, maintenance, spoiler, and concentrator bits as well as 12-bits of the normal fs pattern. additional slc-96 information can be found in bellcore document tr-tsy-000008. to enable the DS26518 to synchronize onto a slc-96 pa ttern, the following configuration should be used: ? rcr1 .5 (rfm) = 1 set to d4 framing mode. ? rcr1 .3 (syncc) = 1 set to cr oss-couple ft and fs bits. ? t1rcr2 .4 (rslc96) = 1 enable slc-96 synchronizer. ? rcr1 .7 (synct) = 0 set to minimum sync time. the slc-96 message bits can be extracted via the t1rslc1 ?3 registers. the status bit rslc96 located at rls7 .3 is useful for retrieving slc-96 message data. t he rslc96 bit will indicate when the framer has updated the data link registers t1rslc1 ?3 with the latest message data from t he incoming data stream. once the rslc96 bit is set, the user will have 9ms (or until the next rslc96 in terrupt) to retrieve the most recent message data from the t1rslc1 ?3 registers. note that rslc96 will not set if the DS26518 is unable to detect the 12-bit slc-96 alignment pattern.
DS26518 8-port t1/e1/j1 transceiver 59 of 286 9.9.5 t1 data link 9.9.5.1 t1 transmit bit-oriented code (boc) transmit controller the DS26518 contains a boc generator on the transmit side and a boc detector on the receive side. the boc function is available only in t1 mode. table 9-19 shows the registers related to the transmit bit-oriented code. table 9-19. registers related to t1 transmit boc register framer 1 addresses function transmit boc register ( t1tboc ) 163h transmit bit-oriented message code register. transmit hdlc control register 2 ( thc2 ) 113h bit to enable sending of transmit boc. transmit control register 1( tcr1 ) 181h determines the sourcing of the f-bit. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. bits 0 to 5 in the t1tboc register contain the boc message to be transmitted. setting sboc = 1 ( thc2 .6) causes the transmit boc controller to immediately begin in serting the boc sequence into the fdl bit position. the transmit boc controller automatically provides the abort sequence. boc messages will be transmitted as long as sboc is set. note that the tfpt ( tcr1 .6) control bit must be set to zero for the boc message to overwrite f-bit information being sampled on tsern. 9.9.5.1.1 to transmit a boc 1) write 6-bit code into the t1tboc register. 2) set sboc bit in thc2 = 1. 9.9.5.2 receive bit-oriente d code (boc) controller the ds26528 framers contain a boc generator on the transm it side and a boc detector on the receive side. the boc function is available only in t1, esf mode in the data link bits. table 9-20 shows the registers related to the receive boc operation. table 9-20. registers related to t1 receive boc register framer 1 addresses function receive boc control register ( t1rbocc ) 015h controls the receive boc function. receive boc register ( t1rboc ) 063h receive bit-oriented message. receive latched status register 7( rls7 ) 096h indicates changes to the receive bit-oriented messages. receive interrupt mask register 7 ( rim7 ) 0a6h mask bits for rboc for generation of interrupts. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. in esf mode, the DS26518 continuously monitors the receive message bits for a valid boc message. the boc detect (bd) status bit at rls7 .0 will be set once a valid message has been detected for time determined by the receive boc filter bits rbf0 and rbf1 in the t1rbocc register. the 6-bit boc message will be available in the rboc register. once the user has clea red the bd bit, it will remain clear unt il a new boc is detec ted (or the same boc is detected following a boc clear event). the boc clear (bc) bit at rls7 .1 is set when a valid boc is no longer being detected for a time determined by the rece ive boc disintegration bits rbd0 and rbd1 in the t1rbocc register. the bd and bc status bits can create a hardware interrupt on the intb signal as enabled by the associated interrupt mask bits in the rim7 register.
DS26518 8-port t1/e1/j1 transceiver 60 of 286 9.9.5.3 legacy t1 transmit fdl it is recommended that the DS26518?s built-in boc or hd lc controllers be used for most applications requiring access to the fdl. table 9-21 shows the registers related to control of the transmit fdl. table 9-21. registers related to t1 transmit fdl register framer 1 addresses function transmit fdl register ( t1tfdl ) 162h fdl code used to insert transmit fdl. transmit control register 2 ( t1.tcr2 ) 182h defines the source of the fdl. transmit latched status register 2 ( tls2 ) 191h transmit fdl empty bit. transmit interrupt mask register 2 ( tim2 ) 1a1h mask bit for tfdl empty. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. when enabled with t1.tcr2 .7, the transmit section will shift out into the t1 data stream, ei ther the fdl (in the esf framing mode) or the fs bits (in the d4 framing mode) contained in the transmit fdl register ( t1tfdl ). when a new value is written to the t1tfdl , it will be multiplexed serially (lsb fi rst) into the proper position in the outgoing t1 data stream. after the full eight bits has been sh ifted out, the framer will signal the host controller that the buffer is empty and that more data is needed by setting the tls2 .4 bit to a one. intb will also toggle low if enabled via tim2 .4. the user has 2ms to update the t1tfdl with a new value. if the t1tfdl is not updated, the old value in the t1tfdl register will be transmitted once again. note that in this mode, no zero stuffing will be applied to the fdl data. it is strongly suggested that the hdlc controller be used for fdl messaging applications. in the d4 framing mode, the framer uses the t1tfdl register to insert the fs fr aming pattern. to accomplish this the t1tfdl register must be programmed to 1ch and t1.tcr2 .7 should be set to 0 (source fs data from the t1tfdl register). the t1tfdl register contains the facility data link (fdl) information that is to be inserted on a byte basis into the outgoing t1 data stream. the lsb is transmitted first. in d4 mode, only the lower six bits are used. 9.9.5.4 legacy t1 receive fdl it is recommended that the DS26518?s built-in boc or hd lc controllers be used for most applications requiring access to the fdl. table 9-22 shows the registers rela ted to the receive fdl. table 9-22. registers related to t1 receive fdl register framer 1 addresses function receive fdl register ( t1rfdl ) 062h fdl code used to receive fdl. receive latched status register 7( rls7 ) 096h receive fdl full bit is in this register. receive interrupt mask register 7( rim7 ) 0a6h mask bit for rfdl full. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. in the receive section, the recovered fdl bits or fs bi ts are shifted bit-by-bit into the receive fdl register ( t1rfdl ). since the t1rfdl is 8 bits in length, it will fill up every 2ms (8 times 250 s). the framer will signal an external controller that the buffer has filled via the rls7 .2 bit. if enabled via rim7 .2, the intb pin will toggle low indicating that the buffer has filled and needs to be read. the user has 2ms to read this data before it is lost. note that no zero destuffing is applied to the for the data provided through the t1rfdl register. the t1rfdl register reports the incoming facility data link (fdl) or the incomi ng fs bits. the lsb is received first. in d4 framing mode, t1rfdl updates on multiframe boundaries and reports only the fs bits.
DS26518 8-port t1/e1/j1 transceiver 61 of 286 9.9.6 e1 data link table 9-23 shows the registers related to e1 data link. table 9-23. registers related to e1 data link register framer 1 addresses function e1 receive align frame register ( e1raf ) 064h receive frame alignment register. e1 receive non-align frame register register ( e1rnaf ) 065h receive non-frame alignment register. e1 received si bits of the align frame register ( e1rsiaf ) 066h receive si bits of the frame alignment frames. received si bits of the non-align frame register e1rsinaf ) 067h receive si bits of the non-frame alignment frames. received sa4 to sa8 bits register ( e1rsa4 to e1rsa8 ) 069h, 06ah, 06bh, 06ch, 06dh receive sa bits. transmit align frame register ( e1taf ) 164h transmit align frame register. transmit non-align frame register ( e1tnaf ) 165h transmit non-align frame register. transmit si bits of the align frame register ( e1tsiaf ) 166h transmit si bits of the frame alignment frames. transmit si bits of the non-align frame register ( e1tsinaf ) 167h transmit si bits of the non-frame alignment frames. transmit sa4 to sa8 bits register ( e1tsa4 to e1tsa8 ) 169h, 16ah, 16bh, 16ch, 16dh transmit sa4 to sa8. e1 transmit sa-bit control register ( e1tsacr ) 114h transmit sources of sa control. note: the addresses shown are for framer 1. addresses for fram ers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex); where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 62 of 286 9.9.6.1 additional e1 receive sa- a nd si-bit receive operation (e1 mode) the DS26518, when operated in the e1 mode, provides for access to both the sa and the si bits via two methods. the first involves using the internal e1raf / e1rnaf and e1taf / e1tnaf registers. the second method involves an expanded version of the first method. 9.9.6.1.1 internal register scheme based on double-frame (method 1) on the receive side, the e1raf and e1rnaf registers will always report the data as it received in the sa and si bit locations. the e1raf and e1rnaf registers are updated on align frame boundaries. the setting of the receive align frame bit in receive latched status register 2 ( rls2 .0) will indicate that the contents of the raf and rnaf have been updated. the host can use the rls2 .0 bit to know when to read the e1raf and e1rnaf registers. the host has 250 s to retrieve the data before it is lost. 9.9.6.1.2 internal regi ster scheme based on crc-4 multiframe (receive) on the receive side, there is a set of eight registers ( e1rsiaf , e1rsinaf , e1rra , e1rsa4 to e1rsa8) that report the si and sa bits as they are received. these regi sters are updated with the se tting of the receive crc-4 multiframe bit in receive latched status register 2 ( rls2 .1). the host can use the rls2 .1 bit to know when to read these registers. the user has 2ms to retrieve the dat a before it is lost. see th e register descriptions for additional information. 9.9.6.1.3 internal regi ster scheme based on crc-4 multiframe (transmit) on the transmit side there is a set of eight registers ( e1tsiaf , e1tsinaf , e1tra , e1tsa4 to e1tsa8 ) that, via the e1 transmit sa-bit control register ( e1tsacr ), can be programmed to insert both si and sa data. data is sampled from these registers with the setting of the transm it multiframe bit in transmit latched status register 1 ( tls1 .3). the host can use the tls1.3 bit to know when to update these registers. it has 2ms to update the data or else the old data will be retransmitted. see the register descriptions in section 10 for more information. 9.9.6.2 sa-bit monitoring and reporting in addition to the registers outlined a bove, the DS26518 provides st atus and interrupt capability in order to detect changes in the state of selected sa bits. the e1rsaimr register can be used to select which sa bits are monitored for a change of state. when a change of state is detected in one of the enabled sa bit positions, a status bit is set in the rls7 register via the saxcd bit (bit 0). this status bit can in turn be used to generate an interrupt by unmasking rim7 .0 (saxcd). if multiple sa bits ha ve been enabled, the user can read the sabits register at address 06eh to determine the current value of each sa bit. for the sa6 bits, additional support is available to detect specific codewords per ets 300 233. the sa6code register will report the received sa6 co deword. the codeword must be stable for a period of three submultiframes and be different from the previous stored value in order to be updated in this register. see the sa6code register description for further details on the operati on of this register and the values reported in it. an additional status bit is provided in rls7 .1 (sa6cd) to indicate if the received sa6 codewo rd has changed. a mask bit is provided for this status bit in rim7 to allow for interrupt generation when enabled. 9.9.7 maintenance and alarms the DS26518 provides extensive functions for alarm detecti on and generation. it also provides diagnostic functions for monitoring of performance and sending of diagnostic information: ? real-time and latched status bits, interrupts and interrupt mask for transmitter and receiver ? los detection ? ria detection and generation ? error counters ? ds0 monitoring ? milliwatt generation and detection ? slip buffer status for transmit and receive
DS26518 8-port t1/e1/j1 transceiver 63 of 286 table 9-24 shows some of the registers re lated to maintenance and alarms. table 9-24. registers related to maintenance and alarms register framer 1 addresses function receive real-time status register 1 ( rrts1 ) 0b0h real-time receive status 1. receive interrupt mask register 1( rim1 ) 0a0h real-time interrupt mask 1. receive latched status register 2 ( rls2 ) 091h real-time latched status 2. receive real-time status register 3 ( rrts3 ) 0b2h real-time receive status 2. receive latched status register 3 ( rls3 ) 092h real-time latched status 3. receive interrupt mask register 3 ( rim3 ) 0a2h real-time interrupt mask 3. receive interrupt mask register 4 ( rim4 ) 0a3h real-time interrupt mask 3. receive latched status register 7 ( rls7 ) 096h real-time latched status 7. receive interrupt mask register 7 ( rim7 ) 0a6h real-time interrupt mask 7. transmit latched status register 1 ( tls1 ) 190h loss of transmit clock status, etc. transmit latched status register 3 (synchronizer) ( tls3 ) 192h loss of frame status. receive ds0 monitor register ( rds0m ) 060h receive ds0 monitor. error-counter configuration register ( ercnt ) 086h configuration of the error counters. line code violation count register 1 ( lcvcr1 ) 050h line code violation counter 1. line code violation count register 2 ( lcvcr2 ) 051h line code violation counter 2. path code violation count register 1 ( pcvcr1 ) 052h receive path code violation counter 1. path code violation count register 2 ( pcvcr2 ) 053h receive path code violation counter 2. frames out of sync count register 1 ( foscr1 ) 054h receive frame out of sync counter 1 frames out of sync count register 2 ( foscr2 ) 055h receive frame out of sync counter 2 e-bit count register 1 ( e1ebcr1 ) 056h e-bit count register 1. e-bit count register 2 ( e1ebcr2 ) 057h e-bit count register 2. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 64 of 286 9.9.7.1 status and information bit operation when a particular event has occurred (or is occurring), the appropriat e bit in one of these registers will be set to a one. status bits may operate in either a latched or real-time fashion. some latched bits may be enabled to generate a hardware interrupt via the intb signal. 9.9.7.1.1 real-time bits some status bits operate in a real-time fashion. these bi ts are read-only and indicate the present state of an alarm or a condition. real-time bits will remain stable, and valid during the host read operation. the current value of the internal status signals can be read at any time from the r eal-time status registers wit hout changing any the latched status register bits. 9.9.7.1.2 latched bits when an event or an alarm occurs and a latched bit is se t to a one, it will remain set until cleared by the user. these bits typically respond on a change -of-state for an alarm, condition, or event; and operate in a read-then-write fashion. the user should read the value of the desired status bit, and then write a 1 to that particular bit location in order to clear the latched value (write a 0 to locations not to be cleared). once the bit is cleared, it will not be set again until the event has occurred again. 9.9.7.1.3 mask bits some of the alarms and events can be either masked or un masked from the interrupt pin via the receive interrupt mask registers ( rim1 , rim3 , rim4 , rim5 , rim7 ). when unmasked, the intb signal will be forced low when the enabled event or condition occurs. the intb pin will be allowed to return high (if no other unmask ed interrupts are present) when the user reads then clears (with a write) the alarm bit that caused the interrupt to occur. note that the latched status bit and the intb pin will clear even if the alarm is still present. note that some conditions may have mu ltiple status indications. for exam ple, receive loss of frame (rlof) provides the following indications: rrts1 .0 (rlof) real-time indication that the receiver is not synchronized with incoming data stream. read-only bit that remains high as long as the condition is present. rls1 .0 (rlofd) latched indication that the receiver has loss synchronization since the bit wa s last cleared. bit will clear when written by the user, even if the condition is still present (rising edge detect of rrts1 .0). rls1 .4 (rlofc) latched indication that the receiver has reacquired synchronization since the bit wa s last cleared. bit will clear when written by the user, even if the condition is still present (falling edge detect of rrts1 .0).
DS26518 8-port t1/e1/j1 transceiver 65 of 286 9.9.8 alarms table 9-25. t1 alarm criteria alarm set criteria clear criteria ais (blue alarm) (see note 1) when over a 3ms window, 4 or fewer zeros are received. when over a 3ms window, 5 or more zeros are received. 1) d4 bit 2 mode ( t1rcr2 .0 = 0) when bit 2 of 256 consecutive channels is set to zero for at least 254 occurrences. when bit 2 of 256 consecutive channels is set to zero for less than 254 occurrences. 2) d4 12th f-bit mode ( t1rcr2 .0 = 1) (note: this mode is also referred to as the ?japanese yellow alarm.?) when the 12th framing bit is set to one for two consecutive occurrences. when the 12th framing bit is set to zero for two consecutive occurrences. 3) esf mode when 16 consecutive patterns of 00ff appear in the fdl. when 14 or fewer patterns of 00ff hex out of 16 possible appear in the fdl. rai (yellow alarm) 4) j1 esf mode (j1 lfa) when 16 consecutive patterns of ffff appear in the fdl. when 14 or fewer patterns of ffff hex out of 16 possible appear in the fdl. los (loss of signal) (note: this alarm is also referred to as receive carrier loss (rcl).) when 192 consecutive zeros are received. when 14 or more ones out of 112 possible bit positions are received starting with the first one received. note 1: the definition of the alarm indication si gnal (blue alarm) is an unframed all-ones signal. ais detectors should be able to oper ate properly in the presence of a 10e-3 error rate and they should not falsely trigger on a framed all-ones signal. the ais alarm c riteria in the DS26518 has been set to achieve this performance. it is recommended that the rais bit be qualified with the rlof bit. note 2: the following terms are equivalent: rais = blue alarm rlos = rcl rlof = loss of frame (conventionally rl os for dallas semiconductor devices) rrai = yellow alarm 9.9.8.1 transmit rai table 9-26 shows the registers related to the transmit rai (yellow alarm). table 9-26. registers related to transmit rai (yellow alarm) register framer 1 addresses function transmit control register 1 ( tcr1 .trai) 181h enable transmission of rai. transmit control register 2 ( t1.tcr2 .trais) 182h select rai to be t1 or j1. transmit control register 4 ( tcr4 .traim) 186h select rai to be normal or rai-ci for t1 esf mode. transmit control register 2 ( e1.tcr2 .ara) 182h selects automatic remote alarm generation in e1 mode. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 66 of 286 9.9.8.2 receive rai table 9-27 shows the registers related to the receive rai (yellow alarm). table 9-27. registers related to receive rai (yellow alarm) register framer 1 addresses function receive control register 2 ( t1rcr2 .rrais) 014h select rai to be t1 or j1. receive control register 2 ( t1rcr2 .raiie) 014h integration enable for t1 esf note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. 9.9.8.3 e1 automatic alarm generation the device can be programmed to automatically transmit ais or remote alarm. when automatic ais generation is enabled ( e1.tcr2 .aais = 1), the device monitors the receive-side framer to determine if any of the following conditions are present/loss of receiv e frame synchronization, ais alarm (all ones) reception, or loss of receive carrier (or signal). if any one (or more) of the above condition s is present, then the framer will either force an ais. when automatic rai generation is enabled ( e1.tcr2 .ara = 1), the framer monitors the receive side to determine if any of the following conditions are present/ loss of receive frame synchroniz ation, ais alarm (all ones) reception, or loss of receive carrier (or signal) or if crc-4 mult iframe synchronization cannot be found within 128ms of fas synchronization (if crc-4 is enabled). if any one (or more) of the above conditions is pr esent, then the framer will transmit a rai alarm. rai generation conforms to ets 300 011 and itu-t g.706 specifications. note: it is an illegal state to have both automatic ais gene ration and automatic remote alarm generation enabled at the same time. 9.9.8.4 receive ais-ci and rai-ci detection ais-ci is a repetitive pattern of 1.26 se conds. it consists of 1.11 seconds of an unframed all-ones pattern and 0.15 seconds of all ones modified by the ais- ci signature. the ais-ci signature is a repetitive pattern 6176 bits in length in which, if the first bit is numbered bit 0, bits 3088, 3474 and 5790 are logical zeros and all other bits in the pattern are logical ones (t1.403). ais-ci is an unframed patte rn, so it is defined for all t1 framing formats. the rais-ci bit is set when the ais-ci pattern has been detected and rais ( rrts1 .2) is set. rais-ci is a latched bit that should be cleared by the host when read. rais-ci w ill continue to set approximately every 1.2 seconds that the condition is present. the host will need to ?poll? t he bit, in conjunction with the normal ais indicators to determine when the condition has cleared. rai-ci is a repetitive pattern within the esf data link wi th a period of 1.08 seconds. it consists of sequentially interleaving 0.99 seconds of ?00000000 11111111? (right-to-left ) with 90 ms of ?00111110 11111111?. the rrai- ci bit is set when a bit oriented code of ?00111110 11111111? is detected while rrai ( rrts1 .3) is set. the rrai- ci detector uses the receive boc filter bits (rbf0 and rb f1) located in rbocc to determine the integration time for rai-ci detection. like rais-ci, the rrai-ci bit is latched and should be cleared by the host when read. rrai- ci will continue to set approximately ev ery 1.1 seconds that the condition is present. the host will need to ?poll? the bit, in conjunction with the normal rai indicators to determine when the condition has cleared. it may be useful to enable the 200ms esf rai integration time with the raiie control bit ( t1rcr2 .1) in networks that utilize rai-ci. 9.9.8.5 t1 receive-side digita l milliwatt code generation receive-side digital milliwatt code generation involves using the t1 receive digital milliwatt registers ( t1rdmwe1 ?3) to determine which of the 24 t1 channels of the t1 line going to the backplane should be overwritten with a digital milliwatt pattern . the digital milliwatt code is an 8-byte repeating pattern that represents a 1khz sine wave (1e/0b/0b/1e/9e/8b/8b/ 9e). each bit in the t1rdmwex registers represents a particular channel. if a bit is set to a one, then the receive data in that channel will be replaced with the digital milliwatt code. if a bit is set to zero, no replacement occurs.
DS26518 8-port t1/e1/j1 transceiver 67 of 286 9.9.9 error count registers the DS26518 contains four counters that are used to accumulate line coding errors, path errors, and synchronization errors. count er update options include one second boundaries, 42ms (t1 mode only), 62.5ms (e1 mode only) or manually. see the erro r counter configuration register ( ercnt ). when updated automatically, the user can use the interrupt from the timer to determine when to read these registers. all four counters will saturate at their respective maximum counts and they will not roll over. ( note: only the line code violation count register has the potential to overflow but the bit error woul d have to exceed 10e-2 before this would occur.) the DS26518 can share the one-second timer from port 1 across all ports. all DS26518 error/performance counters can be configured to update on the shared one- second source or a separate manual update signal input. see the ercnt register for more information. by allowing mult iple framer cores to synchronously latch their counters, the host software can be streamlined to read and process performance information from multiple spans in a more controlled manner. 9.9.9.1 line code violation count register (lcvcr) either bipolar violations or code violations can be counted. bipolar violati ons are defined as consecutive marks of the same polarity. in t1 mode, if the b8zs mode is set for the receive side, then b8zs codewords are not counted as bpvs. in e1 mode, if the hdb3 mode is set for t he receive side, then hdb3 c odewords are not counted as bpvs. if ercnt .0 is set, then the lvc counts code violations as defined in itu-t o.161. code violations are defined as consecutive bipolar violati ons of the same polarity. in most applications, the framer should be programmed to count bpvs when receiving ami code and to count cvs when receiving b8zs or hdb3 code. this counter increments at all times and is not disabled by loss of sync conditions. the counter saturates at 65,535 and will not rollover. the bit error rate on an e1 line would have to be greater than 10e-2 before the vcr would saturate. see table 9-28 and table 9-29 for details of exactly what the lcvcrs count. table 9-28. t1 line code violation counting options count excessive zeros? ( ercnt .0) b8zs enabled? ( rcr1 .6) what is counted in lcvcr1 , lcvcr2 no no bpvs yes no bpvs + 16 consecutive zeros no yes bpvs (b8zs/hdb3 codewords not counted) yes yes bpvs + 8 consecutive zeros table 9-29. e1 line code violation counting options e1 code violation select ( ercnt .0) what is counted in lcvcr1 , lcvcr2 0 bpvs 1 cvs
DS26518 8-port t1/e1/j1 transceiver 68 of 286 9.9.9.2 path code violati on count register (pcvcr) in t1 operation, the path code violation count register records either ft, fs, or crc-6 errors. when the receive side of a framer is set to operate in the t1 esf frami ng mode, pcvcr will record errors in the crc-6 codewords. when set to operate in the t1 d4 framing mode, pcvcr w ill count errors in the ft framing bit position. via the ercnt .2 bit, a framer can be programmed to also report erro rs in the fs framing bit position. the pcvcr will be disabled during receive loss of synchr onization (rlof = 1) conditions. see table 9-30 for a detailed description of exactly what errors the pcvcr counts in t1 operation. in e1 operation, the path code violation count regist er records crc-4 errors. since the maximum crc-4 count in a one second period is 1000, this counter cannot saturate . the counter is disabled during loss of sync at either the fas or crc-4 level; it will continue to count if lo ss of multiframe sync occurs at the cas level. the path code violation count register 1 ( pcvcr1 ) is the most significant word and the path code violation count register 2 ( pcvcr2 ) is the least significant word of a 16-bit counter that records path violations (pvs). table 9-30. t1 path code vi olation counting arrangements framing mode count fs errors? what is counted in pcvcr1 , pcvcr2 ? d4 no errors in the ft pattern d4 yes errors in both the ft and fs patterns esf don?t care errors in the crc-6 codewords 9.9.9.3 frames out of sync count register (foscr) the foscr is used to count the number of multiframes that t he receive synchronizer is out of sync. this number is useful in esf applications needing to measure the paramete rs loss of frame count (lofc) and esf error events as described in at&t publication tr54016. when the fos cr is operated in this mode, it is not disabled during receive loss of synchronization (rlof = 1) conditions. the foscr has alternate operating mode whereby it will count either errors in the ft framin g pattern (in the d4 mode) or errors in the fps framing pattern (in the esf mode). when the foscr is operated in this mode, it is disabled during receive loss of synchronization (rlof = 1) conditions. see table 9-31 for a detailed description of what the foscr is capable of counting. in e1 mode, the foscr counts word erro rs in the frame alignment signal in time slot 0. this counter is disabled when rlof is high. fas errors will not be counted w hen the framer is searching for fas alignment and/or synchronization at either the cas or crc-4 multiframe level. since the maximum fas word error count in a one- second period is 4000, this counter cannot saturate. the frames out of sync count register 1 ( foscr1 ) is the most significant word and the frames out of sync count register 2 foscr2 is the least significant word of a 16-bit counter that records frames out of sync. table 9-31. t1 frames out of sync counting arrangements framing mode ( rcr1 .5) count mos or f-bit errors ( ercnt .1) what is counted in foscr1 , foscr2 d4 mos number of multiframes out of sync d4 f-bit errors in the ft pattern esf mos number of multiframes out of sync esf f-bit errors in the fps pattern 9.9.9.4 e-bit counter (ebcr) this counter is only available in e1 mode. the e-bit count register 1 ( e1ebcr1 ) is the most significant word and the e-bit count register 2 ( e1ebcr2 ) is the least significant word of a 16-bit counter that records far-end block errors (febe) as reported in the first bit of frames 13 and 15 on e1 lines running with crc-4 multiframe. these count registers will increment once each time the received e- bit is set to zero. since the maximum e-bit count in a one-second period is 1000, this counter cannot saturate. the counter is disabled during loss of sync at either the fas or crc-4 level; it will continue to count if loss of multiframe sync occurs at the cas level.
DS26518 8-port t1/e1/j1 transceiver 69 of 286 9.9.10 ds0 monitoring function the DS26518 can monitor one ds0 (64kbps) channel in t he transmit direction and one ds0 channel in the receive direction at the same time. table 9-32 shows the registers related to the control of transmit and receive ds0. table 9-32. registers related to ds0 monitoring register framer 1 addresses function transmit ds0 channel monitor select register ( tds0sel ) 189h transmit channel to be monitored. transmit ds0 monitor register ( tds0m ) 1bbh monitored data. receive channel monitor select register ( rds0sel ) 012h receive channel to be monitored. receive ds0 monitor register ( rds0m ) 060h monitored data. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. in the transmit direction the user will determine which ch annel is to be monitored by properly setting the tcm[4:0] bits in the tds0sel register. in the receive direct ion, the rcm[4:0] bits in the rds0sel register need to be properly set. the ds0 channel pointed to by the tcm[4:0] bits will appear in the transmit ds0 monitor register ( tds0m ) and the ds0 channel pointed to by the rcm[4:0] bi ts will appear in the receive ds0 monitor register ( rds0m ). the tcm[4:0] and rcm[4:0] bits should be programmed with the decimal decode of the appropriate t1or e1 channel. t1 channels 1 to 24 map to register values 0 to 23. e1 channels 1 to 32 map to register values 0 to 31. for example, if ds0 channel 6 in the transmit di rection and ds0 channel 15 in the receive direction needed to be monitored, then the following values would be programmed into tds0sel and rds0sel: tcm4 = 0 rcm4 = 0 tcm3 = 0 rcm3 = 1 tcm2 = 1 rcm2 = 1 tcm1 = 0 rcm1 = 1 tcm0 = 1 rcm0 = 0
DS26518 8-port t1/e1/j1 transceiver 70 of 286 9.9.11 transmit per-channel idle code generation channel data can be replaced by an idle code on a per-ch annel basis in the transmit and receive directions. the transmit idle code definition registers ( tidr1 ?32) are provided to set the 8-bit idle code for each channel. the transmit channel idle code enable registers ( tcice1 ?4) are used to enable idle code replacement on a per- channel basis. 9.9.12 receive per-channel idle code insertion channel data can be replaced by an idle code on a per-chan nel basis in the transmit and receive directions. the receive idle code definition registers ( ridr1 ?32) are provided to set the 8-bit idle code for each channel. the receive channel idle code enable registers ( rcice1 ?4) are used to enable idle code replacement on a per- channel basis. 9.9.13 per-channel loopback the per-channel loopback enable registers ( pcl1 ?4) determine which channels (if any) from the backplane should be replaced with the data from the receive side or in other words, off of the t1 or e1 line. if this loopback is enabled, then transmit and receive clocks and frame syncs must be synchronized. one method to accomplish this would be to tie rclkn to tclkn and rfsyncn to tsyncn. there are no restrictions on which channels can be looped back or on how many channels can be looped back. each of the bit positions in pcl1 ?4) represents a ds0 channel in the outgoi ng frame. when these bits are set to a one, data from the corresponding receive channel will replace the data on tsern for that channel. 9.9.14 e1 g.706 intermediate crc-4 updating (e1 mode only) the DS26518 can implement the g.706 crc-4 recalculati on at intermediate path points. when this mode is enabled, the data stream presented at tsern will already have the fas/nfas, crc multiframe alignment word, and crc-4 checksum in time slot 0. the user can modify the sa-bit positions and this change in data content will be used to modify the crc-4 checksum. this modification, however, will no t corrupt any error information the original crc-4 checksum may contain. in this mode of oper ation, tsyncn must be configured to multiframe mode. the data at tsern must be aligned to the tsyncn signal . if tsyncn is an input then the user must assert tsyncn aligned at the beginning of the multiframe relati ve to tsern. if tsyncn is an output, the user must multiframe align the data presented to tsern. this mode is enabled with the tcr3 .0 control bit (crc4r). note that the e1 transmitter must already be enabled for crc insertion with the tcr1 .0 control bit (tcrc4). see figure 9-16 . figure 9-16. crc-4 recalculate method tsern xor crc-4 calculator extract old crc-4 code insert new crc-4 code modify sa-bit positions new sa-bit data + ttipn/tringn
DS26518 8-port t1/e1/j1 transceiver 71 of 286 9.9.15 t1 programmable in-band loop code generator the DS26518 can generate and detect a repeating bit pattern from one to eight bits or 16 bits in length. this function is available only in t1 mode . table 9-33. registers related to t1 in-band loop code generator register framer 1 addresses function transmit code definition register 1 ( t1tcd1 ) 1ach pattern to be sent for loop code. transmit code definition register 2 ( t1tcd2 ) 1adh length of the pattern to be sent. transmit control register 3 ( tcr3 ) 183h tloop bit for control of number of patterns being sent. transmit control register 4 ( tcr4 ) 186h length of the code being sent. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. to transmit a pattern, the user will lo ad the pattern to be sent into the transmit code definition registers ( t1tcd1 and t1tcd2 ) and select the proper length of the pattern by setting the tc0 and tc1 bits in transmit control register 4 ( tcr4 ). when generating a 1-, 2-, 4-, 8-, or 16-bit pattern both t1tcd1 and t1tcd2 must be filled with the proper code. generation of a 3-, 5-, 6-, and 7-bit pattern only requires t1tcd1 to be filled. once this is accomplished, the pattern w ill be transmitted as long as the tloop control bit ( tcr3 .0) is enabled. normally (unless the transmit formatter is progra mmed to not insert the f-bit position) the framer will over write the repeating pattern once every 193 bits to allow the f-bit position to be sent. as an example, to transmit the stand ard ?loop-up? code for channel servic e units (csus), which is a repeating pattern of ...10000100001..., set tcd1 = 80h, tc0 = 0, tc1 = 0, and tcr3 .0 = 1.
DS26518 8-port t1/e1/j1 transceiver 72 of 286 9.9.16 t1 programmable in-band loop code detection the DS26518 can generate and detect a repeating bit pattern from one to eight bits or 16 bits in length. this function is available only in t1 mode . table 9-34. registers related to t1 in-band loop code detection register framer 1 addresses function receive in-band code control register ( t1ribcc ) 082h used for selecting length of receive in- band loop code register. receive up code definition register 1 ( t1rupcd1 ) 0ach receive up code definition register 1. receive up code definition register 2 ( t1rupcd2 ) 0adh receive up code definition register 2. receive down code definition register 1 ( t1rdncd1 ) 0aeh receive down code definition register 1. receive down code definition register 2 ( t1rdncd2 ) 0afh receive up code definition register 2. receive spare code register 1 ( t1rscd1 ) 09ch receive spare code register 1. receive spare code register 2 ( t1rscd2 ) 09dh receive spare code register 2. receive real-time status register 3 ( rrts3 ) 0b2h real-time loop code detect. receive latched status register 3 ( rls3 ) 092h latched loop code detect bits. receive interrupt mask register 3 ( rim3 ) 0a2h mask for latched loop code detect bits. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8. the framer has three programmable pattern detectors. ty pically, two of the detectors are used for ?loop-up? and ?loop-down? code detection. the user will program the codes to be detected in the receive up code definition registers 1 and 2 ( t1rupcd1 and t1rupcd2 ) and the receive down code definition registers 1 and 2 ( t1rdncd1 and t1rdncd2 ) registers and the length of each pattern will be selected via the t1ribcc register. there is a third detector (spare) an d it is defined and controlled via the t1rscd1 / t1rscd2 and t1rscc registers. when detecting a 16-bit pattern both receive code definition registers are used together to form a 16-bit register. for 8-bit patterns, both receive code definition registers will be filled wi th the same value. detection of a 1-, 2-, 3-, 4-, 5-, 6-, and 7-bit pattern only requires the firs t receive code definition register to be filled. the framer will detect repeating pattern codes in both framed and unframed circumstances with bit error rates as high as 10e?2. the detectors can handle both f-bit inserted and f-bit ov erwrite patterns. writing the least significant byte of receive code definition register rese ts the integration period for that detec tor. the code detector has a nominal integration period of 48ms. hence, after about 48ms of re ceiving a valid code, the prope r status bit (lup, ldn, and lsp) will be set to a one. note that real-time status bits, as well as latched set and clea r bits are available for lup, ldn and lsp ( rrts3 and rls3 ). normally codes are sent for a period of 5 seconds. it is recommend that the software poll the framer every 50ms to 100ms until 5 second s has elapsed to ensure that the code is continuously present.
DS26518 8-port t1/e1/j1 transceiver 73 of 286 9.9.17 framer payload loopbacks the framer, payload, and remote loopbacks are controlled by rcr3 . table 9-35. register relate d to framer payload loopbacks receive control register 3 ( rcr3 ) framer 1 addresses function framer loopback 083h transmit data output from the framer is looped back to the receiver. payload loopback 083h the 192-bit payload data is looped back to the transmitter. remote loopback 083h data recovered by the re ceiver is looped back to the transmitter. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 74 of 286 9.10 hdlc controllers 9.10.1 receive hdlc controller this device has an enhanced hdlc controller that can be ma pped into a single time slot, or sa4 to sa8 bits (e1 mode), or the fdl (t1 mode). the hdlc controller has 64-byte fifo buffer in both the transmit and receive paths. the user can select any specific bits within the time slot (s) to assign to the hdlc controller, as well as specific sa bits (e1 mode). the hdlc controller performs all the necessary ov erhead for generating and receiving performance report messages (prm) as described in ansi t1.403 and t he messages as described in at&t tr54016. the hdlc controller automatically generates and detects flags, gene rates and checks the crc check sum, generates and detects abort sequences, stuffs and destuffs zeros, and byte aligns to the data stream. the 64-byte buffers in the hdlc controller are large enough to allow a full prm to be received or transmitted without host intervention. table 9-36 shows the registers related to the hdlc. table 9-36. registers related to the hdlc register framer 1 addresses function receive hdlc control register ( rhc ) 010h mapping of the hdlc to ds0 or fdl. receive hdlc bit suppress register ( rhbse ) 011h receive hdlc bit suppression register. receive hdlc fifo control register ( rhfc ) 087h determines the length of the receive hdlc fifo. receive hdlc packet bytes available register ( rhpba ) 0b5h tells the user how many bytes are available in the teceive hdlc fifo. receive hdlc fifo register ( rhf ) 0b6h the actual fifo data. receive real-time status register 5 ( rrts5 ) 0b4h indicates the fifo status. receive latched status register 5 ( rls5 ) 094h latched status. receive interrupt mask register 5 ( rim5 ) 0a4h interrupt mask for interrupt generation for the latched status. transmit hdlc control register 1( thc1 ) 110h miscellaneous transmit hdlc control. transmit hdlc bit suppress register ( thbse ) 111h transmit hdlc bit suppress for bits not to be used. transmit hdlc control register 2 ( thc2 ) 113h hdlc to ds0 channel selection and other control. transmit hdlc fifo control register ( thfc ) 187h used to control the transmit hdlc fifo. transmit real-time status register 2 ( trts2 ) 1b1h indicates the real-time st atus of the transmit hdlc fifo. transmit hdlc latched status register 2 ( tls2 ) 191h indicates the fifo status. transmit interrupt mask register 2 (hdlc) register ( tim2 ) 1a1h interrupt mask for the latched status. transmit hdlc fifo buffer available register ( tfba ) 1b3h indicates the number of bytes that can be written into the transmit fifo. transmit hdlc fifo register ( thf ) 1b4h transmit hdlc fifo. note: the addresses shown are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex); where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 75 of 286 9.10.1.1 hdlc fifo control control of the transmit and receive fifos is ac complished via the receive hdlc fifo control ( rhfc ) and transmit hdlc fifo control ( thfc ) registers. the fifo control register s set the watermarks for the fifo. when the receive fifo fills above the high watermark, the rhwm bit ( rrts5 .1) will be set. rhwm and thrm are real-time bits and will remain set as long as the fifo?s write pointer is above the watermark. when the transmit fifo empties below the low watermark, the tlwm bit in the trts2 register will be set. tlwm is a real-time bit and will remain set as long as the transmit fifo?s write pointer is below the watermark. if enabled, this condition can also cause an interrupt via the intb pin. if the receive hdlc fifo does overru n the current packet being processe d is dropped. the receive fifo is emptied. the packet status bit in rrts5 and rls5 .5 (rovr) indicate an overrun. 9.10.1.2 receive packet bytes available the lower 7 bits of the receive hdlc packet bytes available register ( rhpba ) indicates the number of bytes (0 to 64) that can be read from the receive fifo. the value indicated by this register informs the host as to how many bytes can be read from the receive fifo without going pa st the end of a message. this value will refer to one of four possibilities, the first part of a packet, the continuation of a packet, the last part of a packet, or a complete packet. after reading the number of bytes indicated by this register the host then checks the hdlc status registers for detailed message status. if the value in the rhpba register refers to the beginning portion of a message or continuation of a message, then the msb of the rhpba register will return a value of 1. th is indicates that the host c an safely read the number of bytes returned by the lower 7 bits of the rhpba register , but there is no need to chec k the information register since the packet has not yet termi nated (successfully or otherwise). 9.10.1.3 hdlc status and information rrts5 , rls5 , and tls2 provide status information for the hdlc c ontroller. when a particular event has occurred (or is occurring), the appropriat e bit in one of these registers will be set to a one. some of the bi ts in these registers are latched and some are real-time bits that are not latc hed. this section contains r egister descriptions that list which bits are latched and which are real-time. with the latched bits, when an event occurs and a bit is set to a one, it will remain set until the user reads and clears that bit. the bit will be cleared when a 1 is written to the bit and it will not be set again until the event has occurred agai n. the real-time bits report the current instantaneous conditions that are occurring and the hist ory of these bits is not latched. like the other latched status registers, the user will follow a read of the status bit with a write. the byte written to the register will inform the device which of the latched bits the user wi shes to clear (the real-time bits are not affected by writing to the status regist er). the user will write a byte to one of these registers, with a one in the bit positions he or she wishes to clear and a zero in the bit positions he or she does not wish to clear. the hdlc status registers rls5 and tls2 have the ability to initiate a hardware interrupt via the intb output signal. each of the events in this register can be either masked or unmasked from the interrupt pin via the hdlc interrupt mask registers rim5 and tim2 . interrupts will force the intb signal low when the event occurs. the intb pin will be allowed to return high (if no other interrupts are pres ent) when the user reads th e event bit that caused the interrupt to occur. 9.10.1.4 hdlc receive example the hdlc status registers in the ds2 6518 allow for flexible software interfac e to meet the user?s preferences. when receiving hdlc messages, the host can choose to be in terrupt driven, to poll to desi red status registers, or a combination of polling and interrupt processes can be used. an example routine for using the DS26518 hdlc receiver is given in figure 9-17 .
DS26518 8-port t1/e1/j1 transceiver 76 of 286 figure 9-17. hdlc m essage receive example reset receive hdlc controller (rhc.6) configure receive hdlc controller (rhc, rhbse, rhfc) start new message buffer enable interrupts rpe and rhwm start new message buffer interrupt? read register rhpba read n bytes from rx hdlc fifo (rhf) n = rhpba[5..0] ms = 1? (ms = rhpba[7]) no yes no yes read rrts5 for packet status (ps2..0) take appropriate action no action required work another process. read n bytes from rx hdlc fifo (rhf) n = rhpba[5..0] start new message buffer start new message buffer
DS26518 8-port t1/e1/j1 transceiver 77 of 286 9.10.2 transmit hdlc controller 9.10.2.1 fifo information the transmit hdlc fifo buffer available register ( tfba ) indicates the number of bytes that can be written into the transmit fifo. the count form this register informs the host as to ho w many bytes can be written into the transmit fifo without overflowing the buffer. this is a re al-time register. the count shall remain valid and stable during the read cycle. 9.10.2.2 hdlc transmit example the hdlc status registers in the ds2 6518 allow for flexible software interfac e to meet the user?s preferences. when transmitting hdlc messages, the host can choose to be interrupt driven, or to poll to desired status registers, or a combination of polli ng and interrupt processes can be used. figure 9-18 shows an example routine for using the DS26518 hdlc receiver.
DS26518 8-port t1/e1/j1 transceiver 78 of 286 figure 9-18. hdlc message transmit example reset transmit hdlc controller (thc.5) configure transmit hdlc controller (thc1,thc2,thbse,thfc) tlwm interrupt? enable tmend interrupt no action required work another process enable tlwm interrupt and verify tlwm clear read tfba n = tfba[6..0] push message byte into tx hdlc fifo (thf) last byte of message? yes no set teom (thc1.2) push last byte into tx fifo loop n tmend interrupt? yes read tudr status bit tudr = 1 yes disable tmend interrupt resend message disable tmend interrupt prepare new message yes no no no a a a
DS26518 8-port t1/e1/j1 transceiver 79 of 286 9.11 power-supply decoupling table 9-37. recommended supply decoupling supply pins decoupling capacitance notes dvdd33/dvss 0.01 f + 0.1 f + 1 f + 10 f ? dvdd18/dvss 0.01 f + 0.1 f + 1 f + 10 f ? atvdd/atvss 0.1 f (x8) + 1 f (x4) + 10 f (x2) it is recommended to use one 0.1 f cap for each atvdd/atvss pair (8 total), one 1 f for every two atvdd/atvss pairs (4 total), and two 10 f capacitors for the analog transmit supply pins. these capacitors should be located as close to the intended power pins as possible. arvdd/arvss 0.1 f (x8) + 1 f (x4) + 10 f (x2) it is recommended to use one 0.1 f cap for each arvdd/arvss pair (8 total), one 1 f for every two arvdd/arvss pairs (4 total), and two 10 f capacitors for the analog receive supply pins. these capacitors should be located as close to the intended power pins as possible. acvdd/acvss 0.1 f + 1 f + 10 f ?
DS26518 8-port t1/e1/j1 transceiver 80 of 286 9.12 line interface units (lius) the DS26518 has eight identical liu transmit and receive front-ends for each of the eight framers. each liu contains three sections: the transmitter, which waveshape s and drives the network line; the receiver, which handles clock and data recovery; and the jitter attenuator. the DS26518 lius can switch between t1 or e1 networks without changing any external components on either the transmit or receive side. figure 9-19 shows a recommended circuit for software selected termination with pr otection. in this configuration the device can connect to 100 t1 twisted pair, 110 j1 twisted pair, 75 or 120 e1 twisted pair without additional component changes. the signals between the framer and liu are not access ible by the user, thus the framer and liu cannot be separated. the transmitters have fast high-imped ance capability and can be individually powered down. the DS26518?s transmit waveforms meet the correspondi ng g.703 and t1.102 specifications. internal software- selectable transmit termination is provided for 100 t1 twisted pair, 110 j1 twisted pair, 120 e1 twisted pair and 75 e1 coaxial applications. the receiver can connect to 100 t1 twisted pair, 110 j1 twisted pair, 120 e1 twisted pair, and 75 e1 coaxial. the receive liu can function with a receive signal attenuation of up to 36db for t1 mode and 43db for e1 mode. the receiver sensitivity is programmable from 12db to 43db of cable loss. also a monitor gain setting can be enabled to provi de 14db, 20db, 26db, and 32db of resistive gain.
DS26518 8-port t1/e1/j1 transceiver 81 of 286 figure 9-19. network connect ion?longitudinal protection DS26518 ttipn tringn rtipn rringn s1 s2 s3 s4 s5 s6 s7 s8 t1 t2 t3 t4 2:1 1:1 f1 f2 f3 f4 tx tip tx ring rx tip rx ring 560 pf r t 1 uf name description part manufacturer notes 1.25a slow blow fuse smp 1.25 bel fuse 5 f1 to f4 1.25a slow blow fuse f1250t teccor electronics 5 s1, s2 25v (max) transient suppressor p0080sa mc teccor electronics 1, 5 s3, s4, s5, s6 180v (max) transient suppressor p1800s c mc teccor electronics 1, 4, 5 s7, s8 40v (max) transient suppressor p0300sc mc teccor electronics 1, 5 t1 and t2 transformer 1:1ct and 1:2ct (3.3v, smt) pe-68678 pulse engineering 2, 3, 5 t3 and t4 dual common-mode choke (smt) pe-65857 pulse engineering 5 r t termination resistor (120 , 110 , 100 , or 75 ) ? ? ? note 1: changing s7 and s8 to p1800sc devices provides symmetrical voltage suppresion betw een tip, ring, and ground. note 2: the layout from the transformers to the network interface is critical. traces should be at least 25 mils wide and separated from other circuit lines by at least 150 mils. the area under this portion of the circuit should not c ontain power planes. note 3: some t1 (never in e1) applications sour ce or sink power from the network-side center taps of the rx/tx transformers. note 4: the ground trace connected to the s3/s4 pair and the s5/s6 pair sh ould be at least 50 mils wide to conduct the extra current from a longitudinal power-cross event. note 5: alternative component recommendations and line in terface circuits can be found by contacting telecom.support@dalsemi.com or in application note 324 , which is available at www.maxim-ic.com/an324 . note 6: the 1 f capacitor in series with ttipn is only necessary for g.703 clock sync applications. note 7: the 560pf on ttipn/tringn must be tuned to your application.
DS26518 8-port t1/e1/j1 transceiver 82 of 286 9.12.1 liu operation the analog ami/hdb3 waveforms off of the e1 lines or t he ami/b8zs waveform off of the t1 lines are transformer coupled into the rtipn and rringn pins of the DS26518. the user has the option to use internal termination, software selectable for 75 /100 /110 /120 applications, or external terminat ion. the liu recovers clock and data from the analog signal and passes it through the jitter a ttenuation mux. the DS26518 contains an active filter that reconstructs the analog received signal for the nonli near losses that occur in transmission. the receive circuitry also is configurable for various monitor applications . the device has a usable receive sensitivity of 0db to -43db for e1 and 0db to -36db for t1, which allows the device to operate on 0.63mm (22awg) cables up to 2.5km (e1) and 6k feet (t1) in length. data in put to the transmit side of the liu is sent via the jitter attenuation mux to the wave shaping circuitry and line driver. the DS26518 will dr ive the e1 or t1 line from the ttipn and tringn pins via a coupling transformer. the line driver can handle both cept 30/isdn-pri lines for e1 and long-haul (csu) or short-haul (dsx-1) lines for t1. the registers that control the liu o peration are shown in table 9-38 . table 9-38. registers related to control of the liu register framer 1 addresses function global transceiver control register 3 ( gtcr3 ) 00f2h global transceiver control. global transceiver clock control register 1 ( gtccr1 ) 00f3h mps selections, backplane clock selections. global liu software reset register 1 ( gsrr1 ) 00f6h software reset control for the liu. global liu interrupt status register 1 ( glisr1 ) 00fbh interrupt status bit for each of the eight lius. global liu interrupt mask register 1 ( glimr1 ) 00feh interrupt mask register for the liu. liu transmit receive control register ( ltrcr ) 1000h t1/j1/e1 selection, output tri-state, loss criteria. liu transmit impedance and pulse shape selection register ( ltipsr ) 1001h transmit pulse shape and impedance selection. liu maintenance control register ( lmcr ) 1002h transmit maintenance and jitter attenuation control register. liu real status register ( lrsr ) 1003h liu real-time status register. liu status interrupt mask register ( lsimr ) 1004h liu mask registers based on latched status bits. liu latched status register ( llsr ) 1005h liu latched status bits related to loss, open circuit, etc. liu receive signal level register ( lrsl ) 1006h liu receive signal level indicator. liu receive impedance an d sensitivity monitor register ( lrismr ) 1007h liu impedance match and sensitivity monitor. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex), where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 83 of 286 9.12.2 transmitter nrz data arrives from the framer transmitter; the data is encoded with hdb3 or b8zs or ami. the encoded data passes through a jitter attenuator if it is enabled for t he transmit path. a digital sequencer and dac are used to generate transmit waveforms compliant with t1.102 and g.703 pulse templates. a line driver is used to drive an internal matched impedance circuit for provision of 75 , 100 , 110 , and 120 terminations. the transmitter couples to the e1 or t1 transmit twisted pair (or coaxial cable in some e1 applications) via a 1:2 step-up transformer. in order for t he device to create the proper waveforms, the transformer used must meet the specifications listed in table 9-40 . the transmitter requires a transmit clock of 2.048mhz for e1 or 1.544mhz for t1/j1 operation. the DS26518 drivers have a short-circ uit and open-circuit detection driver-fail monitor. the txenable pin can high impedance the transmitter outputs for protection switching. the individual transmitters can also be placed in high impedance through register settings. the DS26518 also has functionality for powering down the transmitters individually. the relevant telecommunications specification compliance is shown in table 9-39 . table 9-39. telecommunications specificati on compliance for DS26518 transmitters transmitter function telecommunications compliance t1 telecom pulse template compliance ansi t1.403 t1 telecom pulse template compliance ansi t1.102 transmit electrical characteristics for e1 transmission and return loss compliance itu-t g.703 table 9-40. transformer specifications specification recommended value turns ratio 3.3v applications 1:1 (receive) and 1:2 (transmit) 2% primary inductance 600 h minimum leakage inductance 1.0 h maximum intertwining capacitance 40pf maximum primary (device side) 1.0 maximum transmit transformer dc resistance secondary 2.0 maximum primary (device side) 1.2 maximum receive transformer dc resistance secondary 1.2 maximum
DS26518 8-port t1/e1/j1 transceiver 84 of 286 9.12.2.1 transmit-line pulse shapes the DS26518 transmitters can be selected individually to meet the pulse templates for e1 and t1/j1 modes. the t1/j1 pulse template is shown in figure 9-20 . the e1 pulse template is shown in figure 9-21 . the transmit pulse shape can be configured for each liu on an individual ba sis. the liu transmit impedan ce selection registers can be used to select an internal tran smit terminating impedance of 100 for t1, 110 for j1 mode, 75 or 120 for e1 mode or no internal termination for e1 or t1 mode. the transmit pulse shape and terminating impedance is selected by ltipsr registers. the pulse shapes will be compli ant to t1.102 and g.703. pulse shapes are measured for compliance at the appropriate network interface (ni). for t1 long haul and e1, the pulse shape is measured at the far end. for t1 short haul, t he pulse shape is measured at the near end. figure 9-20. t1/j1 transmit pulse templates 1.2 0 - 0.1 - 0.2 - 0.3 - 0.4 - 0.5 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 - 500 - 300 - 100 0 300 500 700 - 400 - 200 200 400 600 100 time (ns) normalized amplitude t1.102/87, t1.403, cb 119 (oct. 79), & i.431 template - 0.77 - 0.39 - 0.27 - 0.27 - 0.12 0.00 0.27 0.35 0.93 1.16 - 500 - 255 - 175 - 175 - 75 0 175 225 600 750 0.05 0.05 0.80 1.15 1.15 1.05 1.05 - 0.07 0.05 0.05 - 0.77 - 0.23 - 0.23 - 0.15 0.00 0.15 0.23 0.23 0.46 0.66 0.93 1.16 - 500 - 150 - 150 - 100 0 100 150 150 300 430 600 750 - 0.05 - 0.05 0.50 0.95 0.95 0.90 0.50 - 0.45 - 0.45 - 0.20 - 0.05 - 0.05 ui time amp. maximum curve ui tim e amp. minimum curve - 0.77 - 0.39 - 0.27 - 0.27 - 0.12 0.00 0.27 0.34 0.77 1.16 -500 -255 -175 -175 -75 0 175 225 600 750 0.05 0.05 0.80 1.20 1.20 1.05 1.05 - 0.05 0.05 0.05 - 0.77 - 0.23 - 0.23 - 0.15 0.00 0.15 0.23 0.23 0.46 0.61 0.93 1.16 -500 -150 -150 -100 0 100 150 150 300 430 600 750 - 0.05 - 0.05 0.50 0.95 0.95 0.90 0.50 - 0.45 - 0.45 - 0.26 - 0.05 - 0.05 ui time amp. maximum curve ui time amp. minimum curve dsx - 1 template (pe r ansi t1.102 - 1993) ds1 template (per ansi t1.403 - 1995)
DS26518 8-port t1/e1/j1 transceiver 85 of 286 figure 9-21. e1 transmit pulse templates 0 -0.1 -0.2 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 0 time (ns) scaled amplitude 50 100 150 200 250 -50 -100 -150 -200 -250 269ns 194ns 219ns (in 75 ohm systems, 1.0 on the scale = 2.37vpeak in 120 ohm systems, 1.0 on the scale = 3.00vpeak) g.703 template
DS26518 8-port t1/e1/j1 transceiver 86 of 286 9.12.2.2 transmit g.703 secti on 10 synchronization signal the DS26518 can transmit a 2.048mhz square-wave synchronization clock as specified in section 10 of itu-t g.703. to use this mode, set the transmit g.703 synchr onization clock bit (tg703) found in the liu transmit impedance and pulse shape selection register ( ltipsr ). this mode also requires a 1 f blocking capacitor between ttipn and the transformer. additionally, the following re gisters should set to center the pulse to meet the pulse template: if configuring for e1 75 mode, set register address 0x1229 = 0xf8. if configuring for e1 120 mode, set register addresses 0x1229 = 0xf8 and 0x122d = 0x09. 9.12.2.3 transmit power-down the individual transmitters can be powered down by setting the tpde bit in the liu ma intenance control register ( lmcr ). note that powering down the transmit liu result s in a high-impedance state for the corresponding ttipn and tringn pins. when transmit all ones (ais) is invoked, continuous ones are transmitted using mclk as the timing reference. data input from the framer is ignored. ais can be sent by setting a bit in the lmcr register. transmit all ones will also be sent if the corresponding receiver goes into los state and the atais bit is set in the lmcr l register. 9.12.2.4 transmit short-circuit detector/limiter each transmitter has an automatic short-circuit current limiter that activates when the load resistance is approximately 25 or less. tscs ( lrsr .2) provides a real-time indication of wh en the current limiter is activated. the liu latched status register ( llsr ) provides latched versions of the information, which can be used to activate an interrupt when enable via the lsimr register. 9.12.2.5 transmit open-circuit detector the DS26518 can also detect when the ttipn or tringn outputs are open circuited. ocs ( lrsr .1) will provide a real-time indication of when an open circuit is detected. register llsr provides latched versions of the information, which can be used to activate an interrupt when enabled via the lsimr register. the open-circuit-detect feature is not available in t1 csu operating modes (lbo 5, lbo 6, and lbo 7). 9.12.3 receiver 9.12.3.1 receive internal termination the DS26518 contains eight receivers. the termination circuit provides an analog switch that powers up in the open setting, providing high impedance to the receive line si de. this is useful for redundancy applications and hot swapability. three termination methods are available: ? partially internal impedance match with 120 external resistor. ? fully internal impedance match, no external resistor. ? external resistor termination, internal termination disabled. see the lrismr register for more details. internal impedance match is configurable to 75 , 100 , 110 , or 120 termination by setting the appropriate rimpm[1:0] bits. these bits must be configured to match line impedance even if internal termination is disabled. figure 9-22 shows a diagram of the switch control of terminat ion. if internal impedance match is disabled, the external resistor, r t , must match the line impedance.
DS26518 8-port t1/e1/j1 transceiver 87 of 286 figure 9-22. receive liu termination options receive liu rtipn rringn 1:1 tfr rx line r t r t lrismr.rimpon the device couples to the receive e1 or t1 twisted pair (or coaxial cable in 75 e1 applications) via a 1:1 or 2:1 transformer. see table 9-40 for transformer details. receive sensitivity is configurable by setting the appropriate rsms[1:0] bits ( lrcr ). the DS26518 uses a digital clock recovery system. the resultant e1, t1 or j1 clock derived from mclk is multiplied by 16 via an internal pll and fed to the clock recovery system. the clock recovery system uses the clock from the pll circuit to form a 16 times oversampler, which is used to recover the clock and data. this oversampling technique offers outstanding performance to meet jitter tolerance specifications shown in figure 9-25 . normally, the clock that is output at the rclkn pin is the recovered clock from the e1 ami/hdb3 or t1 ami/b8zs waveform presented at the rtipn and rringn inputs. if the jitter attenuator ( ltrcr ) is placed in the receive path (as is the case in most applications), the jitter attenuato r restores the rclkn to an app roximate 50% duty cycle. if the jitter attenuator is either placed in the transmit path or is disabled, the rclkn output can exhibit slightly shorter high cycles of the clock. this is due to the highl y over-sampled digital clock recovery circuitry. see table 13-3 for more details. when no signal is present at rtipn and rrin gn, a receive carrier loss (rcl) condition will occur and the rclkn will be derived from the mclkt1 or mc lke1 source (depending on the configuration). 9.12.3.2 receive level indicator the DS26518 will report the signal strength at rtipn an d rringn in approximately 2. 5db increments via rsl[3:0] located in the liu receive signal level register ( lrsl ). this feature is helpful when trouble shooting line performance problems. 9.12.3.3 receive g.703 section 10 synchronization signal the DS26518 can receive a 2.048mhz square-wave synchronization clock as specified in section 10 of itu-t g.703. to use this mode, set the receive g.703 clock bi t (rg703) found in the liu receive control register ( lrcr .7).
DS26518 8-port t1/e1/j1 transceiver 88 of 286 9.12.3.4 receiver monitor mode the receive equalizer is equipped with a monitor mode func tion that is used to overcome the signal attenuation caused by the resistive bridge used in monitoring applicat ions. this function allows for a resistive gain of up to 32db along with cable attenuation of 12db to 30db as shown in the liu receive control register ( lrcr ). figure 9-23. typical monitor application primary t1/e1 terminating device monitor port jack t1/e1 line x f m r ds2651x rt rm rm secondary t1/e1 terminating device 9.12.3.5 loss of signal the DS26518 uses both the digital and analog loss-det ection method in compliance with the latest t1.231 for t1/j1 and itu-t g.775 or ets 300 233 for e1 mode of operation. los is detected if the receiver level falls bellow a threshol d analog voltage for certain dur ation. alternatively, this can be termed as having received ?zeros? for a certain dura tion. the signal level and timing duration are defined in accordance with the t1.231 or g.775 or ets 300 233 specifications. for short-haul mode, the loss-detection thresholds are based on cable loss of 12db to 18db for both t1/j1 and e1 modes. the loss thresholds are selectable based on table 10-20 . for long-haul mode, the los-detection threshold is based on cable loss of 30db to 38db for t1/j1 and 30db to 45db for e1 mode. note there is no explicit bit called short-haul mode selection. loss declaration level is set at 3db lower than the maximum sensitivity setting programmed in table 10-20 . the loss state is exited when the receiver detects a certai n ones density at the maximum sensitivity level or higher, which is 3db higher than the loss-detection level. the lo ss-detection signal level and loss-reset signal level are defined with hysteresis to prevent the receiver from bouncing between ?los? and ?no los? states. table 9-41 outlines the specifications governing the loss function.
DS26518 8-port t1/e1/j1 transceiver 89 of 286 table 9-41. t1.231, g.775, and ets 300 233 loss cr iteria specifications standard criteria t1.231 itu-t g.775 ets 300 233 loss detection no pulses are detected for 175 75 bits. no pulses are detected for duration of 10 to 255 bit periods. no pulses are detected for a duration of 2048 bit periods or 1ms. loss reset loss is terminated if a duration of 12.5% ones are detected over duration of 175 75 bits. loss is not terminated if 8 consecutive zeros are found if b8zs encoding is used. if b8zs is not used, loss is not terminated if 100 consecutive pulses are zero. the incoming signal has transitions for duration of 10 to 255 bit periods. loss reset criteria is not defined. 9.12.3.6 ansi t1.231 for t1 and j1 modes for short-haul mode, loss is declared if the received si gnal level is 3db lower from the programmed value (based on table 10-20 ) for a duration of 192-bit periods. hence, if th e sensitivity is programmed to be 12db, loss is declared at 15db. los is reset if all the following crieria are met: 1) 24 or more ones are detected in a 192-bit period with a programmed sensitivity level measured at rtipn and rringn. 2) during the 192 bits, fewer than 10 0 consecutive zeros are detected. for long-haul mode, loss is detected if the received signal level is 3db lo wer from the programmed value (based on table 10-20 ) for a duration of 192-bit periods. hence, if t he sensitivity is programmed to be 30db, the loss declaration level is 33db. los is reset if all the following crieria are met: 1) 24 or more ones are detected in a 192-bit period with a programmed sensitivity level measured at rtipn and rringn. 2) during the 192 bits, fewer than 10 0 consecutive zeros are detected. 9.12.3.7 itu-t g.775 for e1 modes for short-haul mode, loss is declared if the received si gnal level is 3db lower from the programmed value (based on table 10-20 ) for a duration of 192-bit periods. hence, if th e sensitivity is programmed to be 12db, loss is declared at 15db. los is reset if the receive signal level is greater than or equal to the programmed sensitivity level for a duration of 192-bit periods. for long-haul mode, loss is detected if the received signal level is 3db lo wer from the programmed value (based on table 10-20 ) for a duration of 192-bit periods. hence, if t he sensitivity is programmed to be 30db, the loss declaration level is 15db. los is reset if the receive si gnal level is greater than or equal to the programmed sensitivity level for a duration of 192-bit periods. 9.12.3.8 ets 200 233 for e1 modes for short-haul mode, loss is declared if the received si gnal level is 3db lower from the programmed value (based on table 10-20 ) continusou duration of 2048-bit periods (1ms). los is reset if the receive signal level is greater than or equal to the programmed sensitivity level for a duration of 192-bit periods. for long-haul mode, loss is declared if the received signal level is 3db lower from the programmed value (based on table 10-20 ) continuous duration of 2048-bit periods (1ms). los is reset if the receive signal level is greater than or equal to the programmed sensitivit y level for a duration of 192-bit periods.
DS26518 8-port t1/e1/j1 transceiver 90 of 286 9.12.4 hitless protection switching (hps) many current redundancy protection implementations use mechanical relays to switch between primary and backup boards. the switching ti me in relays is typically in the millis econds, making t1/e1 hps impossible. the switching event will likely cause frame-synchronization lo ss in any equipment downstream, affecting the quality of service. the same is also true for tri-stating mechanisms t hat use software or inactive clocks for the triggering of hps. the DS26518 lius feature fast tristatable outputs for tti pn and tringn and fast disabling of internal impedance matching for rtipn and rringn within one-bit period. the txenable pin is used for hitless protection circuits in combination with the ltrcr .rhpm bit. when low, the txenable pin tri-states all eight transmitters, providing a high-impedance state on ttipn and tringn. if the rhpm bit is set, the txenable pin, when low, will also disable the internal termination on rtipn and rringn on a per-port basis, providing a high impedance to the receive line. this is a very useful function in that control can be done through a hardware pin, allowing a quick switch to the backup system for both the rece iver and the transmitter. figure 9-24 shows a typical hps application. figure 9-24. hps block diagram primary board backup board switching control txenable tring rtip ttip rring tring rtip ttip rring line interface card rx tx txenable
DS26518 8-port t1/e1/j1 transceiver 91 of 286 9.12.5 jitter attenuator the DS26518 contains a jitter attenuator that can be set to a depth of 32 or 128 bits via the jads bits in liu transmit and receive control register ( ltrcr ). the 128-bit mode is used in applications where large excurs ions of wander are expected. the 32-bit mode is used in delay sensitive applications. the characteristics of the attenuation are shown in figure 9-25 . the jitter attenuator can be placed in either the receive path or the transmit path, or be disabled by appropriately setting the japs1 and japs0 bits in the liu transmit and receive control register ( ltrcr ). for the jitter attenuator to operate properly, a 2.048mhz, 1.544 mhz, or a multiple of up to 8x clock must be applied at mclk. see the global transcei ver clock control register 1 ( gtccr1 ) for mclk options. itu-t specification g.703 requires an accuracy of 50ppm for both t1/j1 and e1 applications. tr62411 and ansi specs require an accuracy of 32ppm for t1/j1 interfaces. circuitry adjusts either the recovered clock from the clock/data recovery block or the clock applied at the tclkn pin to create a smooth jitter-free cl ock, which is used to clock data out of the jitter attenuator fifo. it is acceptable to provide a gapped/ bursty clock at the tclkn pin if the jitter attenuator is placed in the transmit side. if the incoming jitter exceeds either 120ui p-p (buffer depth is 128-bits) or 28ui p-p (buffer depth is 32 bits), then the DS26518 will set the jitter attenuat or limit trip (jalts) bit in the liu latched status register ( llsr .3). in t1/j1 mode, the jitter attenuator corner fr equency is 3.75hz, and in e1 mode it is 0.6hz. the DS26518 jitter attenuator is compliant wi th the following specifications shown in table 9-42 . table 9-42. jitter attenuator standards compliance standard itu-t i.431, g.703, g.736, g.823 ets 300 011, tbr 12/13 at&t tr62411, tr43802 tr-tsy 009, tr-tsy 253, tr-tsy 499 figure 9-25. jitter attenuation frequency (hz) 0db -20db -40db -60db 1 10 100 1k 10k jitter attenuation (db) 100k tr 62411 (dec. 90) prohibited area c u r v e b c urv e a itu g.7xx prohibited area tbr12 prohibited area t1 e1
DS26518 8-port t1/e1/j1 transceiver 92 of 286 9.12.6 liu loopbacks the DS26518 provides four liu loopbacks for diagnostic purposes: analog loopback, local loopback, remote loopback 1, and remote loopback 2. dual loopback is a combination of local loopback and remote loopback 1. in the loopback diagrams that follow, tsern, tclkn, rsern, and rclkn are inputs/outputs from the framer. figure 9-26. loopback diagram jitter attenuator (in rx path) rser jitter attenuator (in tx path) local loopback jitter attenuator can be assigned to receive path or transmit path or disabled rtip rring ttip tring jaclk master clock pll mclk rclk analog loopback remote 2 loopback remote 1 loopback tser tclk rx liu tx liu tx formatter rx framer 9.12.6.1 analog loopback the analog output of the transmitter ttipn and tringn is looped back to rtipn and rringn of the receiver. data at rtipn and rringn is ignored in analog loopback. this is shown in the figure 9-27 . figure 9-27. analog loopback line driver transmit framer optional jitter a ttenuato r transmit digital transmit a nalog tclk receive framer optional jitter a ttenuato r receive digital receive analog rclk rtip rring tser rser ttip tring
DS26518 8-port t1/e1/j1 transceiver 93 of 286 9.12.6.2 local loopback the transmit system data is looped back to the receive fr amer. this data is also encoded and output on ttipn and tringn. signals at rtipn and rringn are ignored. this loopback is conceptually shown in figure 9-28 . figure 9-28. local loopback line driver transmit framer optional jitter a ttenuator transmit digital transmit a nalog tclk tser receive framer optional jitter a ttenuator receive digital receive a nalog rclk rser rtip rring ttip tring 9.12.6.3 remote loopback 1 the outputs decoded from the receive liu are looped back to the transmit liu, not including the jitter attenuator in the path. remote loopback 2 includes the jitter attenuator in the loopback path. the inputs from the transmit framer are ignored during remote loopback 1. 9.12.6.4 remote loopback 2 the outputs decoded from the receive li u are looped back to the transmit liu, including the jitter attenuator. the inputs from the transmit framer are ignored during remo te loopback 2. this loopbac k is conceptually shown in figure 9-29 . figure 9-29. remote loopback 2 line driver transmit framer optional jitter a ttenuato r transmit digital transmit a nalog tclk tser receive framer optional jitter a ttenuato r receive digital receive a nalog rclk rser rtip rring ttip tring
DS26518 8-port t1/e1/j1 transceiver 94 of 286 9.12.6.5 dual loopback the inputs decoded from the receive liu are looped back to the transmit liu. the inputs from the transmit framer are looped back to the receiver with the optional ji tter attenuator. dual loopback is a combination of local loopback and remote loopback 1. this loopback is invoke d by setting the correct bits in the liu maintenance control register ( lmcr ). this loopback is conceptually shown in figure 9-30 . figure 9-30. dual loopback line driver transmit framer optional jitter attenuator transmit digital transmit analog tclk tser receive framer optional jitter attenuator receive digital receive analog rclk rser rtip rring ttip tring
DS26518 8-port t1/e1/j1 transceiver 95 of 286 9.13 bit error-rate test function (bert) the bert (bit error rate tester) block can generate and detect both pseudorandom and repeating bit patterns. it is used to test and stress data-communication links. bert functionality is dedicated for each of the transceivers. the registers related to the configure, co ntrol, and status of the bert are shown in table 9-43 . table 9-43. registers related to confi gure, control, and status of bert register framer 1 addresses function global bert interrupt status register 1 ( gbisr1 ) 00fah when any of the 8 berts issue an interrupt, a bit will be set. global bert interrupt mask register 1 ( gbimr1 ) 00fdh when any of the 8 berts issue an interrupt, a bit will be set. receive expansion port control register ( rxpc ) 08ah enable for the receiver bert. receive bert port bit suppress register ( rbpbs ) 08bh bit suppression for the receive bert. receive bert port channel select registers 1 to 4 ( rbpcs1 -4) 0d4h, 0d5h, 0d6h, 0d7h channels to be enabled for the framer to accept data from the bert pattern generator transmit expansion port control register ( txpc ) 18ah enable for the transmitter bert. transmit bert port bit suppress register ( tbpbs ) 18bh bit suppression for the transmit bert. transmit bert port channel select registers 1 to 4 ( tbpcs1 -4) 1d4h, 1d5h, 1d6h, 1d7h channels to be enabled for the framer to accept data from the transmit bert pattern generator. bert alternating word count rate register ( bawc ) 1100h bert alternating pattern count register. bert repetitive patte rn set register 1 ( brp1 ) 1101h bert repetitive pattern set register 1. bert repetitive patte rn set register 2 ( brp2 ) 1102h bert repetitive pattern set register 2. bert repetitive patte rn set register 3 ( brp3 ) 1103h bert repetitive pattern set register 3. bert repetitive patte rn set register 4 ( brp4 ) 1104h bert repetitive pattern set register 4. bert control register 1 ( bc1 ) 1105h pattern selection and misc control bert control register 2 ( bc2 ) 1106h bert bit pattern length control bert bit count register 1 ( bbc1 ) 1107h increments for bert bit clocks. bert bit count register 2 ( bbc2 ) 1108h bert bit counter. bert bit count register 3 ( bbc3 ) 1109h bert bit counter. bert bit count register 4 ( bbc4 ) 110ah bert bit counter. bert error count register 1 ( bec1 ) 110bh bert error counter. bert error count register 2 ( bec2 ) 110ch bert error counter. bert error count register 3 ( bec3 ) 110dh bert error counter. bert latched status register ( blsr ) 110eh denotes synchronization loss and other status. bert status interrupt mask register ( bsim ) 110fh bert interrupt mask. note: the addresses shown above are for framer 1. addresses for framers 2 to 8 can be calculated using the following: framer n = (framer 1 address + (n - 1) x 200hex); where n = 2 to 8 for framers 2 to 8.
DS26518 8-port t1/e1/j1 transceiver 96 of 286 the bert block can generate and detect the following patterns: ? the pseudorandom patterns 2e7-1, 2e 9-1, 2e11-1, 2e15-1, and qrss. ? a repetitive pattern from 1 to 32 bits in length. ? alternating (16-bit) words that flip every 1 to 256 words. ? daly pattern. the bert function must be enabled and configured in the txpc and rxpc registers for each port. the bert can then be assigned on a per-channel basis for both the trans mitter and receiver, using the special per-channel function in the tbpcs1 -4 and rbcs1 -4 registers. individual bit positions within the channels can be suppressed with the tbpbs and rbpbs registers. using combinati ons of these functions, the bert pattern can be transmitted and/or received in single or across multiple ds0s, contiguous or broken. transmit and receive bandwidth assignments are independent of each other. the bert receiver has a 32-bit bit counter and a 24-bit er ror counter. the bert rece iver can generate interrupts on: a change in receive-synchronizer status, receive all zero s, receive all ones, error counter overflow, bit counter overflow, and bit error detection. interrupts from each of these events can be masked within the bert function via the bert status interrupt mask register ( bsim ). if the software detects that th e bert has reported an event, then the software must read the bert latched status register ( blsr ) to determine which event(s) has occurred. 9.13.1 bert repetitive pattern set these registers must be properly loaded for the bert to generate and synchronize to a repetitive pattern, a pseudorandom pattern, alternating word pattern, or a daly pattern. for a repetitive pattern that is fewer than 32 bits, the pattern should be repeated so that all 32 bits ar e used to describe the pattern. for example, if the pattern was the repeating 5-bit pattern ?01101 ? (where the rightmost bit is the one sent first and received first), then brp1 should be loaded with adh, brp2 with b5h, brp3 with d6h, and brp4 should be loaded with 5ah. for a pseudo-random pattern, all four registers should be loaded wi th all ones (i.e., ffh). for an alternating word pattern, one word should be placed into brp1 and brp2 and the other word should be placed into brp3 and brp4. for example, if the dds stress pattern ?7e? is to be descri bed, the user would place 00h in brp1, 00h in brp2, 7eh in brp3, and 7eh in brp4, and the alternating word counter wo uld be set to 50 (decimal) to allow 100 bytes of 00h followed by 100 bytes of 7eh to be sent and received. 9.13.2 bert error counter once bert has achieved synchronization, this 24-bit counter will increment for each data bit received in error. toggling the lc control bit in bc1 can clear this coun ter. this counter saturates when full and will set the beco status bit in the blsr register.
DS26518 8-port t1/e1/j1 transceiver 97 of 286 10. device registers thirteen address bits are used to control the settings of the registers. the registers contro l functions of the framers, lius, and berts within the DS26518. the map is divided into eight framers, followed by eight lius and eight berts. global registers (applicable to all eight transceive rs and berts) are located within the address space of framer 1. the register details are provided in the following tables. the framer registers bits are provided for framer 1 and address bits a[12:8] determi ne the framer addressed. 10.1 register listings the framer registers have an offset of 200 hex, the liu registers have an o ffset of 20 hex, and the bert registers have an offset of 10 hex for each transceiver. table 10-1. register address ranges (in hex) channel global receive framer transmit framer liu bert ? 00f0?00ff ? ? ? ? ch1 ? 0000?00ef 0100?01ef 1000?101f 1100?110f ch2 ? 0200?02ef 0300?03ef 1020?103f 1110?111f ch3 ? 0400?04ef 0500?05ef 1040?105f 1120?112f ch4 ? 0600?06ef 0700?07ef 1060?107f 1130?113f ch5 ? 0800?08ef 0900?09ef 1080?109f 1140?114f ch6 ? 0a00?0aef 0b00?0bef 10a0?10bf 1150?115f ch7 ? 0c00?0cef 0d00?0def 10c0?10df 1160?116f ch8 ? 0e00?0eef 0f00?0fef 10e0?10ff 1170?117f
DS26518 8-port t1/e1/j1 transceiver 98 of 286 10.1.1 global register list table 10-2. global register list global register list address name description r/w 00f0h gtcr1 global transceiver control register 1 r/w 00f1h gfcr1 global framer control register 1 r/w 00f2h gtcr3 global transceiver control register 3 r/w 00f3h gtccr1 global transceiver clock control register 1 r/w 00f4h gtccr3 global transceiver clock control register 3 r/w 00f5h ? reserved ? 00f6h gsrr1 global liu software reset register 1 r/w 00f7h ? reserved ? 00f8h idr device identification register r 00f9h gfisr1 global framer interrupt status register 1 r 00fah gbisr1 global bert interrupt status register 1 r 00fbh glisr1 global liu interrupt status register 1 r 00fch gfimr1 global framers interrupt mask register 1 rw 00fdh gbimr1 global bert interrupt mask register 1 rw 00feh glimr1 global liu interrupt mask register 1 rw note 1: reserved registers should only be written with all zeros. note 2: the global registers are located in the framer address space. the corresponding address space for the other seven framers is ?reserved,? and should be initialized with all zeros for proper operation.
DS26518 8-port t1/e1/j1 transceiver 99 of 286 10.1.2 framer register list table 10-3. framer register list note that only framer 1 address is presented here. the same set of registers definitions applies for transceivers 2 to 8 in acc ordance with the DS26518 map offsets. transceiver offset is [(n - 1) x 200 hex], where n designates th e transceiver in question. framer register list address name description r/w 000h e1rdmwe1 e1 receive digital milliwatt enable register 1 r/w 001h e1rdmwe2 e1 receive digital milliwatt enable register 2 r/w 002h e1rdmwe3 e1 receive digital milliwatt enable register 3 r/w 003h e1rdmwe4 e1 receive digital milliwatt enable register 4 r/w 004h?00fh ? reserved ? 010h rhc receive hdlc control register r/w 011h rhbse receive hdlc bit suppress register r/w 012h rds0sel receive channel monitor select register r/w 013h rsigc receive-signaling control register r/w t1rcr2 receive control register 2 (t1 mode) 014h e1rsaimr receive sa-bit interrupt mask register (e1 mode) r/w 015h t1rbocc receive boc control register (t1 mode only) r/w 016h?01fh ? reserved ? 020h ridr1 receive idle code definition register 1 r/w 021h ridr2 receive idle code definition register 2 r/w 022h ridr3 receive idle code definition register 3 r/w 023h ridr4 receive idle code definition register 4 r/w 024h ridr5 receive idle code definition register 5 r/w 025h ridr6 receive idle code definition register 6 r/w 026h ridr7 receive idle code definition register 7 r/w 027h ridr8 receive idle code definition register 8 r/w 028h ridr9 receive idle code definition register 9 r/w 029h ridr10 receive idle code definition register 10 r/w 02ah ridr11 receive idle code definition register 11 r/w 02bh ridr12 receive idle code definition register 12 r/w 02ch ridr13 receive idle code definition register 13 r/w 02dh ridr14 receive idle code definition register 14 r/w 02eh ridr15 receive idle code definition register 15 r/w 02fh ridr16 receive idle code definition register 16 r/w 030h ridr17 receive idle code definition register 17 r/w 031h ridr18 receive idle code definition register 18 r/w 032h ridr19 receive idle code definition register 19 r/w 033h ridr20 receive idle code definition register 20 r/w 034h ridr21 receive idle code definition register 21 r/w 035h ridr22 receive idle code definition register 22 r/w 036h ridr23 receive idle code definition register 23 r/w 037h ridr24 receive idle code definition register 24 r/w t1rsaoi1 receive-signaling all-ones insertion register 1 (t1 mode only) 038h ridr25 receive idle code definition register 25 (e1 mode) r/w t1rsaoi2 receive-signaling all-ones insertion register 2 (t1 mode only) 039h ridr26 receive idle code definition register 26 (e1 mode) r/w t1rsaoi3 receive-signaling all-ones insertion register 3 (t1 mode only) 03ah ridr27 receive idle code definition register 27 (e1 mode) r/w 03b ridr28 receive idle code definition register 28 (e1 mode) ? t1rdmwe1 t1 receive digital milliwatt enable register 1 (t1 mode only) 03c ridr29 receive idle code definition register 29 (e1 mode) r/w 03dh t1rdmwe2 t1 receive digital milliwatt enable register 2 (t1 mode only) r/w
DS26518 8-port t1/e1/j1 transceiver 100 of 286 framer register list address name description r/w ridr30 receive idle code definition register 30 (e1 mode) t1rdmwe3 t1 receive digital milliwatt enable register 3 (t1 mode only) 03eh ridr31 receive idle code definition register 31 (e1 mode) r/w 03fh ridr32 receive idle code definition register 32 (e1 mode) ? 040h rs1 receive-signaling register 1 r 041h rs2 receive-signaling register 2 r 042h rs3 receive-signaling register 3 r 043h rs4 receive-signaling register 4 r 044h rs5 receive-signaling register 5 r 045h rs6 receive-signaling register 6 r 046h rs7 receive-signaling register 7 r 047h rs8 receive-signaling register 8 r 048h rs9 receive-signaling register 9 r 049h rs10 receive-signaling register 10 r 04ah rs11 receive-signaling register 11 r 04bh rs12 receive-signaling register 12 r 04ch rs13 receive-signaling r egister 13 (e1 mode only) ? 04dh rs14 receive-signaling r egister 14 (e1 mode only) ? 04eh rs15 receive-signaling register 15 (e1 mode only) ? 04fh rs16 receive-signaling register 16 (e1 mode only) ? 050h lcvcr1 line code violation count register 1 r 051h lcvcr2 line code violation count register 2 r 052h pcvcr1 path code violation count register 1 r 053h pcvcr2 path code violation count register 2 r 054h foscr1 frames out of sync count register 1 r 055h foscr2 frames out of sync count register 2 r 056h e1ebcr1 e-bit count 1 (e1 mode only) r 057h e1ebcr2 e-bit count 2 (e1 mode only) r 058h feacr1 error count a register 1 r/w 059h feacr2 error count a register 2 r/w 05ah febcr1 error count b register 1 r/w 05bh febcr2 error count b register 2 r/w 060h rds0m receive ds0 monitor register r 061h ? reserved ? t1rfdl receive fdl register (t1 mode) 062h e1rrts7 receive real-time status register 7 (e1 mode) r 063h t1rboc receive boc register (t1 mode) r t1rslc1 receive slc-96 data link register 1 (t1 mode) 064h e1raf e1 receive align frame register (e1 mode) r t1rslc2 receive slc-96 data link register 2 (t1 mode) 065h e1rnaf e1 receive non-align frame register (e1 mode) r t1rslc3 receive slc-96 data link register 3 (t1 mode) 066h e1rsiaf e1 received si bits of the align frame register (e1 mode) r 067h e1rsinaf received si bits of the non-a lign frame register (e1 mode) r 068h e1rra received remote alarm register (e1 mode) r 069h e1rsa4 e1 receive sa4 bits register (e1 mode only) r 06ah e1rsa5 e1 receive sa5 bits register (e1 mode only) r 06bh e1rsa6 e1 receive sa6 bits register (e1 mode only) r 06ch e1rsa7 e1 receive sa7 bits register (e1 mode only) r 06dh e1rsa8 receive sa8 bits register (e1 mode only) r 06eh sabits e1 receive sax bits register r 06fh sa6code received sa6 codeword register r 070h?07fh ? reserved ?
DS26518 8-port t1/e1/j1 transceiver 101 of 286 framer register list address name description r/w 080h rmmr receive master mode register r/w rcr1 receive control register 1 (t1 mode) 081h rcr1 receive control register 1 (e1 mode) r/w t1ribcc receive in-band code control register (t1 mode) 082h e1rcr2 receive control register 2 (e1 mode) r/w 083h rcr3 receive control register 3 r/w 084h riocr receive i/o configuration register r/w 085h rescr receive elastic store control register r/w 086h ercnt error-counter configuration register r/w 087h rhfc receive hdlc fifo control register r/w 088h riboc receive interleave bus operation control register r/w 089h t1rscc in-band receive spare control register (t1 mode only) r/w 08ah rxpc receive expansion port control register r/w 08b rbpbs receive bert port bit suppress register r/w 08ch?08fh ? reserved ? 090h rls1 receive latched status register 1 r/w rls2 receive latched status register 2 (t1 mode) 091h rls2 receive latched status register 2 (e1 mode) r/w rls3 receive latched status register 3 (t1 mode) 092h rls3 receive latched status register 3 (e1 mode) r/w 093h rls4 receive latched status register 4 r/w 094h rls5 receive latched status r egister 5 (hdlc) r/w 095h ? reserved ? rls7 receive latched status register 7 (t1 mode) 096h rls7 receive latched status register 7 (e1 mode) r/w 097h ? reserved ? 098h rss1 receive-signaling status register 1 r/w 099h rss2 receive-signaling status register 2 r/w 09ah rss3 receive-signaling status register 3 r/w 09bh rss4 receive-signaling status register 4 (e1 mode only) r/w 09ch t1rscd1 receive spare code definition register 1 (t1 mode only) r/w 09dh t1rscd2 receive spare code definition register 2 (t1 mode only) r/w 09eh ? reserved ? 09fh riir receive interrupt information register r/w 0a0h rim1 receive interrupt mask register 1 r/w 0a1h rim2 receive interrupt mask register 2 (e1 mode only) r/w rim3 receive interrupt mask register 3 (t1 mode) 0a2h rim3 receive interrupt mask register 3 (e1 mode) r/w 0a3h rim4 receive interrupt mask register 4 r/w 0a4h rim5 receive interrupt mask register 5 (hdlc) r/w 0a5h ? reserved ? rim7 receive interrupt mask register 7 (boc:fdl) (t1 mode) 0a6h rim7 receive interrupt mask register 7 (boc:fdl) (e1 mode) r/w 0a7h ? reserved ? 0a8h rscse1 receive-signaling change of state enable register 1 r/w 0a9h rscse2 receive-signaling change of state enable register 2 r/w 0aah rscse3 receive-signaling change of state enable register 3 r/w 0abh rscse4 receive-signaling change of state en able register 4 (e1 mode only) ? 0ach t1rupcd1 receive up code definition register 1 (t1 mode only) r/w 0adh t1rupcd2 receive up code definition register 2 (t1 mode only) r/w 0aeh t1rdncd1 receive down code definition register 1 (t1 mode only) r/w 0afh t1rdncd2 receive down code definition register 2 (t1 mode only) r/w 0b0h rrts1 receive real-time status register 1 r
DS26518 8-port t1/e1/j1 transceiver 102 of 286 framer register list address name description r/w 0b1h ? reserved ? rrts3 receive real-time status register 3 (t1 mode) 0b2h rrts3 receive real-time status register 3 (e1 mode) r 0b3h ? reserved ? 0b4h rrts5 receive real-time status register 5 (hdlc) r 0b5h rhpba receive hdlc packet bytes available register r 0b6h rhf receive hdlc fifo register r 0b7h?0bfh ? reserved ? 0c0h rbcs1 receive blank channel select register 1 r/w 0c1h rbcs2 receive blank channel select register 2 r/w 0c2h rbcs3 receive blank channel select register 3 r/w 0c3h rbcs4 receive blank channel select register 4 (e1 mode only) r/w 0c4h rcbr1 receive channel blocking register 1 r/w 0c5h rcbr2 receive channel blocking register 2 r/w 0c6h rcbr3 receive channel blocking register 3 r/w 0c7h rcbr4 receive channel blocking register 4 (e1 mode only) r/w 0c8h rsi1 receive-signaling reinsertion enable register 1 r/w 0c9h rsi2 receive-signaling reinsertion enable register 2 r/w 0cah rsi3 receive-signaling reinsertion enable register 3 r/w 0cbh rsi4 receive-signaling reinsertion enabl e register 4 (e1 mode only) r/w 0cch rgccs1 receive gapped clock channel select register 1 r/w 0cdh rgccs2 receive gapped clock channel select register 2 r/w 0ceh rgccs3 receive gapped clock channel select register 3 r/w 0cfh rgccs4 receive gapped clock channel select register (e1 mode only) r/w 0d0h rcice1 receive channel idle code enable register 1 r/w 0d1h rcice2 receive channel idle code enable register 2 r/w 0d2h rcice3 receive channel idle code enable register 3 r/w 0d3h rcice4 receive channel idle code enable register 4 (e1 mode only) r/w 0d4h rbpcs1 receive bert port channel select register 1 r/w 0d5h rbpcs2 receive bert port channel select register 2 r/w 0d6h rbpcs3 receive bert port channel select register 3 r/w 0d7h rbpcs4 receive bert port channel select register 4 (e1 mode only) r/w 0d8h?0efh ? reserved ? 0f0h?0ffh global registers (section 10.3 ) see the global register list in table 10-2 . note that this space is ?reserved? in framers 2 to 8. r/w 100h tdmwe1 transmit digital milliwatt enable register 1 (t1 and e1 modes) r/w 101h tdmwe2 transmit digital milliwatt enable register 2 (t1 and e1 modes) r/w 102h tdmwe3 transmit digital milliwatt enable register 3 (t1 and e1 modes) r/w 103h tdmwe4 transmit digital milliwatt enable register 4 (t1 and e1 modes) r/w 104h tjbe1 transmit jammed bit eight stuffing register 1 r/w 105h tjbe2 transmit jammed bit eight stuffing register 2 r/w 106h tjbe3 transmit jammed bit eight stuffing register 3 r/w 107h tjbe4 transmit jammed bit eight stuffing register 4 r/w 108h tdds1 transmit dds zero code register 1 r/w 109h tdds2 transmit dds zero code register 2 r/w 10ah tdds3 transmit dds zero code register 3 r/w 110h thc1 transmit hdlc control register 1 r/w 111h thbse transmit hdlc bit suppress register r/w 112h ? reserved ? 113h thc2 transmit hdlc control register 2 r/w 114h e1tsacr e1 transmit sa-bit control register (e1 mode) r/w 115h?117h ? reserved ?
DS26518 8-port t1/e1/j1 transceiver 103 of 286 framer register list address name description r/w 118h ssie1 software-signaling insertion enable register 1 r/w 119h ssie2 software-signaling insertion enable register 2 r/w 11ah ssie3 software-signaling insertion enable register 3 r/w 11bh ssie4 software-signaling insertion enable register 4 (e1 mode only) r/w 11ch?11fh ? reserved ? 120h tidr1 transmit idle code definition register 1 r/w 121h tidr2 transmit idle code definition register 2 r/w 122h tidr3 transmit idle code definition register 3 r/w 123h tidr4 transmit idle code definition register 4 r/w 124h tidr5 transmit idle code definition register 5 r/w 125h tidr6 transmit idle code definition register 6 r/w 126h tidr7 transmit idle code definition register 7 r/w 127h tidr8 transmit idle code definition register 8 r/w 128h tidr9 transmit idle code definition register 9 r/w 129h tidr10 transmit idle code definition register 10 r/w 12ah tidr11 transmit idle code definition register 11 r/w 12bh tidr12 transmit idle code definition register 12 r/w 12ch tidr13 transmit idle code definition register 13 r/w 12dh tidr14 transmit idle code definition register 14 r/w 12eh tidr15 transmit idle code definition register 15 r/w 12fh tidr16 transmit idle code definition register 16 r/w 130h tidr17 transmit idle code definition register 17 r/w 131h tidr18 transmit idle code definition register 18 r/w 132h tidr19 transmit idle code definition register 19 r/w 133h tidr20 transmit idle code definition register 20 r/w 134h tidr21 transmit idle code definition register 21 r/w 135h tidr22 transmit idle code definition register 22 r/w 136h tidr23 transmit idle code definition register 23 r/w 137h tidr24 transmit idle code definition register 24 r/w 138h tidr25 transmit idle code definition register 25 (e1 mode only) r/w 139h tidr26 transmit idle code definition register 26 (e1 mode only) r/w 13ah tidr27 transmit idle code defini tion register 27 (e1 mode only) r/w 13bh tidr28 transmit idle code defini tion register 28 (e1 mode only) r/w 13ch tidr29 transmit idle code defini tion register 29 (e1 mode only) r/w 13dh tidr30 transmit idle code defini tion register 30 (e1 mode only) r/w 13eh tidr31 transmit idle code defini tion register 31 (e1 mode only) r/w 13fh tidr32 transmit idle code definition register 32 (e1 mode only) r/w 140h ts1 transmit-signaling register 1 r/w 141h ts2 transmit-signaling register 2 r/w 142h ts3 transmit-signaling register 3 r/w 143h ts4 transmit-signaling register 4 r/w 144h ts5 transmit-signaling register 5 r/w 145h ts6 transmit-signaling register 6 r/w 146h ts7 transmit-signaling register 7 r/w 147h ts8 transmit-signaling register 8 r/w 148h ts9 transmit-signaling register 9 r/w 149h ts10 transmit-signaling register 10 r/w 14ah ts11 transmit-signaling register 11 r/w 14bh ts12 transmit-signaling register 12 r/w 14ch ts13 transmit-signaling register 13 r/w 14dh ts14 transmit-signaling register 14 r/w 14eh ts15 transmit-signaling register 15 r/w 14fh ts16 transmit-signaling register 16 r/w
DS26518 8-port t1/e1/j1 transceiver 104 of 286 framer register list address name description r/w 150h tcice1 transmit channel idle code enable register 1 r/w 151h tcice2 transmit channel idle code enable register 2 r/w 152h tcice3 transmit channel idle code enable register 3 r/w 153h tcice4 transmit channel idle code enable register 4 (e1 mode only) r/w 154h?161h ? reserved ? 162h t1tfdl transmit fdl register (t1 mode only) r/w 163h t1tboc transmit boc register (t1 mode only) r/w t1tslc1 transmit slc-96 data link register 1 (t1 mode) 164h e1taf transmit align frame register (e1 mode) r/w t1tslc2 transmit slc-96 data link register 2 (t1 mode) 165h e1tnaf transmit non-align frame register (e1 mode) r/w t1tslc3 transmit slc-96 data link register 3 (t1 mode) 166h e1tsiaf transmit si bits of the align frame register (e1 mode) r/w 167h e1tsinaf transmit si bits of the non-ali gn frame register (e1 mode only) r/w 168h e1tra transmit remote alarm register (e1 mode) r/w 169h e1tsa4 transmit sa4 bits register (e1 mode only) r/w 16ah e1tsa5 transmit sa5 bits register (e1 mode only) r/w 16bh e1tsa6 transmit sa6 bits register (e1 mode only) r/w 16ch e1tsa7 transmit sa7 bits register (e1 mode only) r/w 16dh e1tsa8 transmit sa8 bits register (e1 mode only) r/w 16eh?17fh ? reserved ? 180h tmmr transmit master mode register r/w tcr1 transmit control register 1 (t1 mode) 181h tcr1 transmit control register 1 (e1 mode) r/w t1.tcr2 transmit control register 2 (t1 mode) 182h e1.tcr2 transmit control register 2 (e1 mode) r/w 183h tcr3 transmit control register 3 r/w 184h tiocr transmit i/o configuration register r/w 185h tescr transmit elastic store control register r/w 186h tcr4 transmit control register 4 (t1 mode only) r/w 187h thfc transmit hdlc fifo control register r/w 188h tiboc transmit interleave bus operation control register r/w 189h tds0sel transmit ds0 channel monitor select register r/w 18ah txpc transmit expansion port control register r/w 18bh tbpbs transmit bert port bit suppress register r/w 18ch?18dh ? reserved ? 18eh tsyncc transmit synchronizer control register r/w 18f ? reserved ? 190h tls1 transmit latched status register 1 r/w 191h tls2 transmit latched status register 2 (hdlc) r/w 192h tls3 transmit latched status regi ster 3 (synchronizer) r/w 193h?19eh ? reserved ? 19fh tiir transmit interrupt information register r/w 1a0h tim1 transmit interrupt mask register 1 r/w 1a1h tim2 transmit interrupt mask register 2 (hdlc) r/w 1a2h tim3 transmit interrupt mask register 3 (synchronizer) r/w 1a3h?1abh ? reserved ? 1ach t1tcd1 transmit code definition register 1 (t1 mode only) r/w 1adh t1tcd2 transmit code definition register 2 (t1 mode only) r/w 1aeh?1b0h ? reserved ? 1b1h trts2 transmit real-time status register 2 (hdlc) r 1b2h ? reserved ? 1b3h tfba transmit hdlc fifo buffer available register r
DS26518 8-port t1/e1/j1 transceiver 105 of 286 framer register list address name description r/w 1b4h thf transmit hdlc fifo register w 1b5h?1bha ? reserved ? 1bbh tds0m transmit ds0 monitor register r 1bch?1bfh ? reserved ? 1c0h tbcs1 transmit blank channel select register 1 r/w 1c1h tbcs2 transmit blank channel select register 2 r/w 1c2h tbcs3 transmit blank channel select register 3 r/w 1c3h tbcs4 transmit blank channel select register 4 (e1 mode only) r/w 1c4h tcbr1 transmit channel blocking register 1 r/w 1c5h tcbr2 transmit channel blocking register 2 r/w 1c6h tcbr3 transmit channel blocking register 3 r/w 1c7h tcbr4 transmit channel blocking register 4 (e1 mode only) r/w 1c8h thscs1 transmit hardware-signaling ch annel select register 1 r/w 1c9h thscs2 transmit hardware-signaling ch annel select register 2 r/w 1cah thscs3 transmit hardware-signaling ch annel select register 3 r/w 1cbh thscs4 transmit hardware-signaling chann el select register 4 (e1 mode only) r/w 1cch tgccs1 transmit gapped-clock channel select register 1 r/w 1cdh tgccs2 transmit gapped-clock channel select register 2 r/w 1ceh tgccs3 transmit gapped-clock channel select register 3 r/w 1cfh tgccs4 transmit gapped-clock channel select register 4 (e1 mode only) r/w 1d0h pcl1 per-channel loopback enable register 1 r/w 1d1h pcl2 per-channel loopback enable register 2 r/w 1d2h pcl3 per-channel loopback enable register 3 r/w 1d3h pcl4 per-channel loopback enable register 4 (e1 mode only) r/w 1d4h tbpcs1 transmit bert port channel select register 1 r/w 1d5h tbpcs2 transmit bert port channel select register 2 r/w 1d6h tbpcs3 transmit bert port channel select register 3 r/w 1d7h tbpcs4 transmit bert port channel select register 4 (e1 mode only) r/w 1d8h?1ffh ? reserved ?
DS26518 8-port t1/e1/j1 transceiver 106 of 286 10.1.3 liu and bert register list table 10-4. liu register list note that only the liu 1 address is presented here. the same set of registers definitions applies for lius 2 to 8 in accordance with the DS26518 map offsets. liu offset is [1000+ (n - 1) x 20 hex], where n designates the liu in question. liu register list address name description 1000h ltrcr liu transmit receive control register 1001h ltipsr liu transmit impedance and pulse shape selection register 1002h lmcr liu maintenance control register 1003h lrsr liu real status register 1004h lsimr liu status interrupt mask register 1005h llsr liu latched status register 1006h lrsl liu receive signal level register 1007 lrismr liu receive impedance and sens itivity monitor register 1008h lrcr liu receive control register 1009h?101fh ? reserved table 10-5. bert register list note that only the bert 1 address is presented here. the same se t of registers definitions applies for berts 2 to 8 in accordan ce with the DS26518 map offsets. bert offset is [1100+ (n - 1) x 10 hex], where n designates t he bert channel in question. bert register list address name description 1100h bawc bert alternating word count rate register 1101h brp1 bert repetitive patte rn set register 1 1102h brp2 bert repetitive patte rn set register 2 1103h brp3 bert repetitive patte rn set register 3 1104h brp4 bert repetitive patte rn set register 4 1105h bc1 bert control register 1 1106h bc2 bert control register 2 1107h bbc1 bert bit count register 1 1108h bbc2 bert bit count register 2 1109h bbc3 bert bit count register 3 110ah bbc4 bert bit count register 4 110bh bec1 bert error count register 1 110ch bec2 bert error count register 2 110dh bec3 bert error count register 3 110eh blsr bert latched status register 110fh bsim bert status interrupt mask register
DS26518 8-port t1/e1/j1 transceiver 107 of 286 10.2 register bit maps 10.2.1 global register bit map table 10-6. global register bit map addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 00f0h gtcr1 gpsel3 gpsel2 gpsel1 ? 528md gibo gcle gipi 00f1h gfcr1 iboms1 iboms0 bpclk1 bpclk0 ? rfmss tcbcs rcbcs 00f2h gtcr3 ? ? ? ? ? ? tssynciosel tsyncsel 00f3h gtccr1 bprefsel3 bprefsel2 bprefsel1 bprefsel0 b f r e q s e l f r e q s e l m p s 1 m p s 0 00f4h gtccr3 rsysclksel tsysclksel t c l k s e l c l k o s e l 3 c l k o s e l 2 c l k o s e l 1 c l k o s e l 0 00f5h ? ? ? ? ? ? ? ? ? 00f6h gsrr1 ? ? ? ? ? lrst brst frst 00f7h ? ? ? ? ? ? ? ? ? 00f8h idr id7 id6 id5 id4 id3 id2 id1 id0 00f9h gfisr1 fis8 fis7 fis6 fis5 fis4 fis3 fis2 fis1 00fah gbisr1 bis8 bis7 bis6 bis5 bis4 bis3 bis2 bis1 00fbh glisr1 lis8 lis7 lis6 lis5 lis4 lis3 lis2 lis1 00fch gfimr1 fim8 fim7 fim6 fim5 fim4 fim3 fim2 fim1 00fdh gbimr1 bim8 bim7 bim6 bim5 bim4 bim3 bim2 bim1 00feh glimr1 lim8 lim7 lim6 lim5 lim4 lim3 lim2 lim1
DS26518 8-port t1/e1/j1 transceiver 108 of 286 10.2.2 framer register bit map table 10-7 contains the framer register s of the DS26518. some register s have dual functionality based on the selection of t1/j1 or e1 operating mode in the rmmr and tmmr registers. these dual -function registers are shown below using two lines of text. the first line of text is the bit functionality for t1/j1 mode. the second line is the bit functionality in e1 mode, in italics . bits that are not used for an operating mode are denoted with a single dash ???. when there is only one set of bit definitions liste d for a register, the bit functionality does not change with respect to the selection of t1/j1 or e1 mode. all regist ers not listed are reserved and should be initialized with a value of 00h for proper operation. the addresses shown are for framer 1. addresses for framers 2 to 8 can be calculated using the following formula: address for framer n = (framer 1 address + (n - 1) x 200hex). table 10-7. framer register bit map addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 000h e1rdmwe1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 001h e1rdmwe2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 002h e1rdmwe3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 003h e1rdmwe4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 010h rhc rcrcd rhr rhms rhcs4 rhcs3 rhcs2 rhcs1 rhcs0 011h rhbse bse8 bse7 bse6 bse5 bse4 bse3 bse2 bse1 012h rds0sel ? ? ? rcm4 rcm3 rcm2 rcm1 rcm0 ? ? ? rfsa1 ? rsff rsfe rsie 013h rsigc ? ? ? casms ? rsff rsfe rsei t1rcr2 ? ? ? rslc96 oof2 oof1 raiie rrais 014h e1rsaimr ? ? ? rsa4im rsa5im rsa6im rsa7im rsa8im 015h t1rbocc rbr ? rbd1 rbd0 ? rbf1 rbf0 ? 020h ridr1 c7 c6 c5 c4 c3 c2 c1 c0 021h ridr2 c7 c6 c5 c4 c3 c2 c1 c0 022h ridr3 c7 c6 c5 c4 c3 c2 c1 c0 023h ridr4 c7 c6 c5 c4 c3 c2 c1 c0 024h ridr5 c7 c6 c5 c4 c3 c2 c1 c0 025h ridr6 c7 c6 c5 c4 c3 c2 c1 c0 026h ridr7 c7 c6 c5 c4 c3 c2 c1 c0 027h ridr8 c7 c6 c5 c4 c3 c2 c1 c0 028h ridr9 c7 c6 c5 c4 c3 c2 c1 c0 029h ridr10 c7 c6 c5 c4 c3 c2 c1 c0 02ah ridr11 c7 c6 c5 c4 c3 c2 c1 c0 02bh ridr12 c7 c6 c5 c4 c3 c2 c1 c0 02ch ridr13 c7 c6 c5 c4 c3 c2 c1 c0 02dh ridr14 c7 c6 c5 c4 c3 c2 c1 c0 02eh ridr15 c7 c6 c5 c4 c3 c2 c1 c0 02fh ridr16 c7 c6 c5 c4 c3 c2 c1 c0 030h ridr17 c7 c6 c5 c4 c3 c2 c1 c0 031h ridr18 c7 c6 c5 c4 c3 c2 c1 c0 032h ridr19 c7 c6 c5 c4 c3 c2 c1 c0 033h ridr20 c7 c6 c5 c4 c3 c2 c1 c0 034h ridr21 c7 c6 c5 c4 c3 c2 c1 c0 035h ridr22 c7 c6 c5 c4 c3 c2 c1 c0 036h ridr23 c7 c6 c5 c4 c3 c2 c1 c0 037h ridr24 c7 c6 c5 c4 c3 c2 c1 c0 t1rsaoi1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 038h ridr25 c7 c6 c5 c4 c3 c2 c1 c0 t1rsaoi2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 039h ridr26 c7 c6 c5 c4 c3 c2 c1 c0
DS26518 8-port t1/e1/j1 transceiver 109 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 t1rsaoi3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 03ah ridr27 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 03bh ridr28 c7 c6 c5 c4 c3 c2 c1 c0 t1rdmwe1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 03ch ridr29 c7 c6 c5 c4 c3 c2 c1 c0 t1rdmwe2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 03dh ridr30 c7 c6 c5 c4 c3 c2 c1 c0 t1rdmwe3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 03eh ridr31 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 03fh ridr32 c7 c6 c5 c4 c3 c2 c1 c0 ch1-a ch1-b ch1-c ch1-d ch13-a ch13-b ch13-c ch13-d 040h rs1 0 0 0 0 x y x x ch2-a ch2-b ch2-c ch2-d ch14-a ch14-b ch14-c ch14-d 041h rs2 ch1-a ch1-b ch1-c ch1-d ch16-a ch16-b ch16-c ch16-d ch3-a ch3-b ch3-c ch3-d ch15-a ch15-b ch15-c ch15-d 042h rs3 ch2-a ch2-b ch2-c ch2-d ch17-a ch17-b ch17-c ch17-d ch4-a ch4-b ch4-c ch4-d ch16-a ch16-b ch16-c ch16-d 043h rs4 ch3-a ch3-b ch3-c ch3-d ch18-a ch18-b ch18-c ch18-d ch5-a ch5-b ch5-c ch5-d ch17-a ch17-b ch17-c ch17-d 044h rs5 ch4-a ch4-b ch4-c ch4-d ch19-a ch19-b ch19-c ch19-d ch6-a ch6-b ch6-c ch6-d ch18-a ch18-b ch18-c ch18-d 045h rs6 ch5-a ch5-b ch5-c ch5-d ch20-a ch20-b ch20-c ch20-d ch7-a ch7-b ch7-c ch7-d ch19-a ch19-b ch19-c ch19-d 046h rs7 ch6-a ch6-b ch6-c ch6-d ch21-a ch21-b ch21-c ch21-d ch8-a ch8-b ch8-c ch8-d ch20-a ch20-b ch20-c ch20-d 047h rs8 ch7-a ch7-b ch7-c ch7-d ch22-a ch22-b ch22-c ch22-d ch9-a ch9-b ch9-c ch9-d ch21-a ch21-b ch21-c ch21-d 048h rs9 ch8-a ch8-b ch8-c ch8-d ch23-a ch23-b ch23-c ch23-d ch10-a ch10-b ch10-c ch10-d ch22-a ch22-b ch22-c ch22-d 049h rs10 ch9-a ch9-b ch9-c ch9-d ch24-a ch24-b ch24-c ch24-d ch11-a ch11-b ch11-c ch11-d ch23-a ch23-b ch23-c ch23-d 04ah rs11 ch10-a ch10-b ch10-c ch10-d ch25-a ch25-b ch25-c ch25-d ch12-a ch12-b ch12-c ch12-d ch24-a ch24-b ch24-c ch24-d 04bh rs12 ch11-a ch11-b ch11-c ch11-d ch26-a ch26-b ch26-c ch26-d ? ? ? ? ? ? ? ? 04ch rs13 ch12-a ch12-b ch12-c ch12-d ch27-a ch27-b ch27-c ch27-d ? ? ? ? ? ? ? ? 04dh rs14 ch13-a ch13-b ch13-c ch13-d ch28-a ch28-b ch28-c ch28-d ? ? ? ? ? ? ? ? 04eh rs15 ch14-a ch14-b ch14-c ch14-d ch29-a ch29-b ch29-c ch29-d ? ? ? ? ? ? ? ? 04fh rs16 ch15-a ch15-b ch15-c ch15-d ch30-a ch30-b ch30-c ch30-d 050h lcvcr1 lcvc15 lcvc14 lcvc13 lcvc12 lcvc11 lcvc10 lcvc9 lcvc8 051h lcvcr2 lcvc7 lcvc6 lcvc5 lcvc4 lcvc3 lcvc2 lcvc1 lcvc0 052h pcvcr1 pcvc15 pcvc14 pcvc 13 pcvc12 pcvc11 pcvc10 pcvc9 pcvc8 053h pcvcr2 pcvc7 pcvc6 pcvc5 pcvc4 pcvc3 pcvc2 pcvc1 pcvc0
DS26518 8-port t1/e1/j1 transceiver 110 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 054h foscr1 fos15 fos14 fos13 fos12 fos11 fos10 fos9 fos8 055h foscr2 fos7 fos6 fos5 fos4 fos3 fos2 fos1 fos0 056h e1ebcr1 eb15 eb14 eb13 eb12 eb11 eb10 eb9 eb8 057h e1ebcr2 eb7 eb6 eb5 eb4 eb3 eb2 eb1 eb0 058h feacr1 feacr15 feacr14 feacr13 feacr12 feacr11 feacr10 feacr9 feacr8 059h feacr2 feacr7 feacr6 feacr5 feacr4 feacr3 feacr2 feacr1 feacr0 05ah febcr1 febcr15 febcr14 febcr13 febcr12 febcr11 febcr10 febcr9 febcr8 05bh febcr2 febcr7 febcr6 febcr5 febcr4 febcr3 febcr2 febcr1 febcr0 060h rds0m b1 b2 b3 b4 b5 b6 b7 b8 061h ? ? ? ? ? ? ? ? ? t1rfdl rfdl7 rfdl6 rfdl5 rfdl4 rfdl3 rfdl2 rfdl1 rfdl0 062h e1rrts7 csc5 csc4 csc3 csc2 csc0 crc4sa cassa fassa 063h t1rboc ? ? rboc5 rboc4 rboc3 rboc2 rboc1 rboc0 t1rslc1 c8 c7 c6 c5 c4 c3 c2 c1 064h e1raf si 0 0 1 1 0 1 1 t1rslc2 m2 m1 s=0 s=1 s=0 c11 c10 c9 065h e1rnaf si 1 a sa4 sa5 sa6 sa7 sa8 t1rslc3 s=1 s4 s3 s2 s1 a2 a1 m3 066h e1rsiaf sif14 sif12 sif10 sif8 sif6 sif4 sif2 sif0 067h e1rsinaf sif15 sif13 sif11 sif9 sif7 sif5 sif3 sif1 068h e1rra rraf15 rraf13 rraf11 rraf9 rraf7 rraf5 rraf3 rraf1 069h e1rsa4 rsa4f15 rsa4f13 rsa4f11 rsa4f9 rsa4f7 rsa4f5 rsa4f3 rsa4f1 06ah e1rsa5 rsa5f15 rsa5f13 rsa5f11 rsa5f9 rsa5f7 rsa5f5 rsa5f3 rsa5f1 06bh e1rsa6 rsa6f15 rsa6f13 rsa6f11 rsa6f9 rsa6f7 rsa6f5 rsa6f3 rsa6f1 06ch e1rsa7 rsa7f15 rsa7f13 rsa7f11 rsa7f9 rsa7f7 rsa7f5 rsa7f3 rsa7f1 06dh e1rsa8 rsa8f15 rsa8f13 rsa8f11 rsa8f9 rsa8f7 rsa8f5 rsa8f3 rsa8f1 06eh sabits ? ? ? sa4 sa5 sa6 sa7 sa8 06fh sa6code ? ? ? ? sa6n sa6n sa6n sa6n 080h rmmr frm_en init_done ? ? ? ? sftrst t1/e1 rcr1 (t1) synct rb8zs rfm arc syncc rjc synce resync 081h rcr1 (e1) ? rhdb3 rsigm rg802 rcrc4 frc synce resync t1ribcc ? ? rup2 rup1 rup0 rdn2 rdn1 rdn0 082h e1rcr2 ? ? ? ? ? ? ? rlosa 083h rcr3 ? ualaw rserc binv1 binv0 ? plb flb rclkinv rsyncinv h100en rsclkm rsms rsio rsms2 rsms1 084h riocr rclkinv rsyncinv h100en rsclkm ? rsio rsms2 rsms1 085h rescr rdatfmt rgclken ? rszs resalgn resr resmdm rese 1secs mcus mecu ecus eams fsbe moscrf lcvcrf 086h ercnt 1secs mcus mecu ecus eams ? ? lcvcrf 087h rhfc ? ? ? ? ? ? rfhwm1 rfhwm0 088h riboc ? ? ? ibosel iboen ? ? ? 089h t1rscc ? ? ? ? ? rsc2 rsc1 rsc0 ? ? ? ? ? rbpdir rbpfus rbpen 08ah rxpc ? ? ? ? ? rbpdir ? rbpen 08bh rbpbs bpbse8 bpbse7 bpbse6 bpbse5 bpbse4 bpbse3 bpbse2 bpbse1 090h rls1 rraic raisc rlosc rlofc rraid raisd rlosd rlofd rls2 (t1) ? ? cofa 8zd 16zd sefe b8zs fbe 091h rls2 (e1) ? crcrc casrc fasrc rsa1 rsa0 rcmf raf 092h rls3 (t1) lorcc lspc ldnc lupc lorcd lspd ldnd lupd
DS26518 8-port t1/e1/j1 transceiver 111 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 rls3 (e1) lorcc ? v52lnkc rdmac lorcd ? v52lnkd rdmad 093h rls4 resf resem rslip ? rscos 1sec timer rmf 094h rls5 ? ? rovr rhobt rpe rps rhwms rnes rls7 (t1) ? ? rrai-ci rais-ci rslc96 rfdlf bc bd 096h rls7 (e1) ? ? ? ? ? ? sa6cd saxcd 097h ? ? ? ? ? ? ? ? ? 098h rss1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 099h rss2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 09ah rss3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 09bh rss4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 c7 c6 c5 c4 c3 c2 c1 c0 09ch t1rscd1 ? ? ? ? ? ? ? ? c7 c6 c5 c4 c3 c2 c1 c0 09dh t1rscd2 ? ? ? ? ? ? ? ? 09fh riir ? rls7 rls6* rls5 rls4 rls3 rls2** rls1 0a0h rim1 rraic raisc rlosc rlofc rraid raisd rlosd rlofd ? ? ? ? ? ? ? ? 0a1h rim2 ? ? ? ? rsa1 rsa0 rcmf raf rim3 (t1) lorcc lspc ldnc lupc lorcd lspd ldnd lupd 0a2h rim3 (e1) lorcc ? v52lnkc rdmac lorcd ? v52lnkd rdmad 0a3h rim4 resf resem rslip ? rscos 1sec timer rmf 0a4h rim5 ? ? rovr rhobt rpe rps rhwms rnes rim7 (t1) ? ? rrai-ci rais-ci rslc96 rfdlf bc bd 0a6h rim7 (e1) ? ? ? ? sa6cd saxcd 0a8h rscse1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 0a9h rscse2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 0aah rscse3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 0abh rscse4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 c7 c6 c5 c4 c3 c2 c1 c0 0ach t1rupcd1 ? ? ? ? ? ? ? ? c7 c6 c5 c4 c3 c2 c1 c0 0adh t1rupcd2 ? ? ? ? ? ? ? ? c7 c6 c5 c4 c3 c2 c1 c0 0aeh t1rdncd1 ? ? ? ? ? ? ? ? c7 c6 c5 c4 c3 c2 c1 c0 0afh t1rdncd2 ? ? ? ? ? ? ? ? 0b0h rrts1 ? ? ? ? rrai rais rlos rlof rrts3 (t1) ? ? ? ? lorc lsp ldn lup 0b2h rrts3 (e1) ? ? ? ? lorc ? v52lnk rdma 0b4h rrts5 ? ps2 ps1 ps0 ? ? rhwm rne 0b5h rhpba ms rpba6 rpba5 rpba4 rpba3 rpba2 rpba1 rpba0 0b6h rhf rhd7 rhd6 rhd5 rhd4 rhd3 rhd2 rhd1 rhd0 0c0h rbcs1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 0c1h rbcs2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 0c2h rbcs3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 0c3h rbcs4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 0c4h rcbr1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1
DS26518 8-port t1/e1/j1 transceiver 112 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 0c5h rcbr2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 0c6h rcbr3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 0c7h rcbr4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25(f-bit) 0c8h rsi1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 0c9h rsi2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 0cah rsi3 ch24 ch23 ch22 ch21 ch200 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 0cbh rsi4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 0cch rgccs1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 0cdh rgccs2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 0ceh rgccs3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 0cfh rgccs4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25(f-bit) 0d0h rcice1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 0d1h rcice2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 0d2h rcice3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 0d3h rcice4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 0d4h rbpcs1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 0d5h rbpcs2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 0d6h rbpcs3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 0d7h rbpcs4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 100h tdmwe1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 101h tdmwe2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 102h tdmwe3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 103h tdmwe4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 104h tjbe1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 105h tjbe2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 106h tjbe3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 107h tjbe4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 108h tdds1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 109h tdds2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 10ah tdds3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 110h thc1 nofs teoml thr thms tfs teom tzsd tcrcd 111h thbse tbse8 tbse7 tbse6 tbse5 tbse4 tbse3 tbse2 tbse1 tabt sboc thcen thcs4 thcs3 thcs2 thcs1 thcs0 113h thc2 tabt ? thcen thcs4 thcs3 thcs2 thcs1 thcs0 118h ssie1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 119h ssie2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 11ah ssie3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 11bh ssie4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 120h tidr1 c7 c6 c5 c4 c3 c2 c1 c0 121h tidr2 c7 c6 c5 c4 c3 c2 c1 c0 122h tidr3 c7 c6 c5 c4 c3 c2 c1 c0 123h tidr4 c7 c6 c5 c4 c3 c2 c1 c0 124h tidr5 c7 c6 c5 c4 c3 c2 c1 c0 125h tidr6 c7 c6 c5 c4 c3 c2 c1 c0
DS26518 8-port t1/e1/j1 transceiver 113 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 126h tidr7 c7 c6 c5 c4 c3 c2 c1 c0 127h tidr8 c7 c6 c5 c4 c3 c2 c1 c0 128h tidr9 c7 c6 c5 c4 c3 c2 c1 c0 129h tidr10 c7 c6 c5 c4 c3 c2 c1 c0 12ah tidr11 c7 c6 c5 c4 c3 c2 c1 c0 12bh tidr12 c7 c6 c5 c4 c3 c2 c1 c0 12ch tidr13 c7 c6 c5 c4 c3 c2 c1 c0 12dh tidr14 c7 c6 c5 c4 c3 c2 c1 c0 12eh tidr15 c7 c6 c5 c4 c3 c2 c1 c0 12fh tidr16 c7 c6 c5 c4 c3 c2 c1 c0 130h tidr17 c7 c6 c5 c4 c3 c2 c1 c0 131h tidr18 c7 c6 c5 c4 c3 c2 c1 c0 132h tidr19 c7 c6 c5 c4 c3 c2 c1 c0 133h tidr20 c7 c6 c5 c4 c3 c2 c1 c0 134h tidr21 c7 c6 c5 c4 c3 c2 c1 c0 135h tidr22 c7 c6 c5 c4 c3 c2 c1 c0 136h tidr23 c7 c6 c5 c4 c3 c2 c1 c0 137h tidr24 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 138h tidr25 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 139h tidr26 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 13ah tidr27 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 13bh tidr28 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 13ch tidr29 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 13dh tidr30 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 13eh tidr31 c7 c6 c5 c4 c3 c2 c1 c0 ? ? ? ? ? ? ? ? 13fh tidr32 c7 c6 c5 c4 c3 c2 c1 c0 ch1-a ch1-b ch1-c ch1-d ch13-a ch13-b ch13-c ch13-d 140h ts1 0 0 0 0 x y x x ch2-a ch2-b ch2-c ch2-d ch14-a ch14-b ch14-c ch14-d 141h ts2 ch1-a ch1-b ch1-c ch1-d ch16-a ch16-b ch16-c ch16-d ch3-a ch3-b ch3-c ch3-d ch15-a ch15-b ch15-c ch15-d 142h ts3 ch2-a ch2-b ch2-c ch2-d ch17-a ch17-b ch17-c ch17-d ch4-a ch4-b ch4-c ch4-d ch16-a ch16-b ch16-c ch16-d 143h ts4 ch3-a ch3-b ch3-c ch3-d ch18-a ch18-b ch18-c ch18-d ch5-a ch5-b ch5-c ch5-d ch17-a ch17-b ch17-c ch17-d 144h ts5 ch4-a ch4-b ch4-c ch4-d ch19-a ch19-b ch19-c ch19-d ch6-a ch6-b ch6-c ch6-d ch18-a ch18-b ch18-c ch18-d 145h ts6 ch5-a ch5-b ch5-c ch5-d ch20-a ch20-b ch20-c ch20-d ch7-a ch7-b ch7-c ch7-d ch19-a ch19-b ch19-c ch19-d 146h ts7 ch6-a ch6-b ch6-c ch6-d ch21-a ch21-b ch21-c ch21-d 147h ts8 ch8-a ch8-b ch8-c ch8-d ch20-a ch20-b ch20-c ch20-d
DS26518 8-port t1/e1/j1 transceiver 114 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 ch7-a ch7-b ch7-c ch7-d ch22-a ch22-b ch22-c ch22-d ch9-a ch9-b ch9-c ch9-d ch21-a ch21-b ch21-c ch21-d 148h ts9 ch8-a ch8-b ch8-c ch8-d ch23-a ch23-b ch23-c ch23-d ch10-a ch10-b ch10-c ch10-d ch22-a ch22-b ch22-c ch22-d 149h ts10 ch9-a ch9-b ch9-c ch9-d ch24-a ch24-b ch24-c ch24-d ch11-a ch11-b ch11-c ch11-d ch23-a ch23-b ch23-c ch23-d 14ah ts11 ch10-a ch10-b ch10-c ch10-d ch25-a ch25-b ch25-c ch25-d ch12-a ch12-b ch12-c ch12-d ch24-a ch24-b ch24-c ch24-d 14bh ts12 ch11-a ch11-b ch11-c ch11-d ch26-a ch26-b ch26-c ch26-d ? ? ? ? ? ? ? ? 14ch ts13 ch12-a ch12-b ch12-c ch12-d ch27-a ch27-b ch27-c ch27-d ? ? ? ? ? ? ? ? 14dh ts14 ch13-a ch13-b ch13-c ch13-d ch28-a ch28-b ch28-c ch28-d ? ? ? ? ? ? ? ? 14eh ts15 ch14-a ch14-b ch14-c ch14-d ch29-a ch29-b ch29-c ch29-d ? ? ? ? ? ? ? ? 14fh ts16 ch15-a ch15-b ch15-c ch15-d ch30-a ch30-b ch30-c ch30-d 150h tcice1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 151h tcice2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 152h tcice3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 153h tcice4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 tfdl7 tfdl6 tfdl5 tfdl4 tfdl3 tfdl2 tfdl1 tfdl0 162h t1tfdl ? ? ? ? ? ? ? ? ? ? tboc5 tboc4 tboc3 tboc2 tboc1 tboc0 163h t1tboc ? ? ? ? ? ? ? ? t1tslc1 c8 c7 c6 c5 c4 c3 c2 c1 164h e1taf si 0 0 1 1 0 1 1 t1tslc2 m2 m1 s=0 s=1 s=0 c11 c10 c9 165h e1tnaf si 1 a sa4 sa5 sa6 sa7 sa8 t1tslc3 s=1 s4 s3 s2 s1 a2 a1 m3 166h e1tsiaf tsif14 tsif12 tsif10 tsif8 tsif6 tsif4 tsif2 tsif0 ? ? ? ? ? ? ? ? 167h e1tsinaf tsif15 tsif13 tsif11 tsif9 tsif7 tsif5 tsif3 tsif1 ? ? ? ? ? ? ? ? 168h e1tra traf15 traf13 traf11 traf9 traf7 traf5 traf3 traf1 ? ? ? ? ? ? ? ? 169h e1tsa4 tsa4f15 tsa4f13 tsa4f11 tsa4f9 tsa4f7 tsa4f5 tsa4f3 tsa4f1 ? ? ? ? ? ? ? ? 16ah e1tsa5 tsa5f15 tsa5f13 tsa5f11 tsa5f9 tsa5f7 tsa5f5 tsa5f3 tsa5f1 ? ? ? ? ? ? ? ? 16bh e1tsa6 tsa6f15 tsa6f13 tsa6f11 tsa6f9 tsa6f7 tsa6f5 tsa6f3 tsa6f1 ? ? ? ? ? ? ? ? 16ch e1tsa7 tsa7f15 tsa7f13 tsa7f11 tsa7f9 tsa7f7 tsa7f5 tsa7f3 tsa7f1 ? ? ? ? ? ? ? ? 16dh e1tsa8 tsa8f15 tsa8f13 tsa8f11 tsa8f9 tsa8f7 tsa8f5 tsa8f3 tsa8f1 180h tmmr frm_en init_done ? ? ? ? sftrst t1/e1 tcr1 (t1) tjc tfpt tcpt tsse gb7s tb8zs tais trai 181h tcr1 (e1) ttpt t16s tg802 tsis tsa1 thdb3 tais tcrc4
DS26518 8-port t1/e1/j1 transceiver 115 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 t1.tcr2 (t1) tfdls tslc96 tddsen fbct2 fbct1 trais ? tb7zs 182h e1.tcr2 (e1) aebe aais ara ? ? ? ? ? ? ? tcss1 tcss0 mfrs tfm ibpv tloop 183h tcr3 ? ? tcss1 tcss0 mfrs ? ibpv crc4r tclkinv tsyncinv tssyncinv tsclkm tssm tsio tsdw tsm 184h tiocr tclkinv tsyncinv tssyncinv tsclkm tssm tsio ? tsm 185h tescr tdatfmt tgclken ?? tszs tesalgn tesr tesmdm tese ualaw binv1 binv0 tjben traim taism tc1 tc0 186h tcr4 ualaw binv1 binv0 tjben ? ? ? ? 187h thfc ? ? ? ? ? ? tflwm1 tflwm0 188h tiboc ? ? ? ibosel iboen ? ? ? 189h tds0sel ? ? ? tcm4 tcm3 tcm2 tcm1 tcm0 18ah txpc ? ? ? ? ? tbpdir tbpfus tbpen 18bh tbpbs bpbse8 bpbse7 bpbse6 bpbse5 bpbse4 bpbse3 bpbse2 bpbse1 ? ? ? ? ? tsen synce resync 18eh tsyncc ? ? ? ? crc4 tsen synce resync tesf tesem tslip tslc96 ? tmf lotcc lotc 190h tls1 tesf tesem tslip ? taf tmf lotcc lotc ? ? ? tfdle tudr tmend tlwms tnfs 191h tls2 ? ? ? ? tudr tmend tlwms tnfs 192h tls3 ? ? ? ? ? ? lof lofd 19fh tiir ? ? ? ? ? tls3 tls2 tls1 tesf tesem tslip tslc96 ? tmf lotcc lotc 1a0h tim1 tesf tesem tslip ? taf tmf lotcc lotc ? ? ? tfdle tudr tmend tlwms tnfs 1a1h tim2 ? ? ? ? tudr tmend tlwms tnfs 1a2h tim3 ? ? ? ? ? ? ? lofd c7 c6 c5 c4 c3 c2 c1 c0 1ach t1tcd1 ? ? ? ? ? ? ? ? c7 c6 c5 c4 c3 c2 c1 c0 adh t1tcd2 ? ? ? ? ? ? ? ? 1b1h trts2 ? ? ? ? tempty tfull tlwm tnf 1b3h tfba ?? tfba6 tfba5 tfba4 tfb a3 tfba2 tfba1 tfba0 1b4h thf thd7 thd6 thd5 thd4 thd3 thd2 thd1 thd0 1bbh tds0m b1 b2 b3 b4 b5 b6 b7 b8 1c0h tbcs1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 1c1h tbcs2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 1c2h tbcs3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 1c3h tbcs4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 1c4h tcbr1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 1c5h tcbr2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 1c6h tcbr3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 1c7h tcbr4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25:fbit 1c8h thscs1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 1c9h thscs2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9
DS26518 8-port t1/e1/j1 transceiver 116 of 286 addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 1cah thscs3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 1cbh thscs4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 1cch tgccs1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 1cdh tgccs2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 1ceh tgccs3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 1cfh tgccs4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25(f-bit) 1d0h pcl1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 1d1h pcl2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 1d2h pcl3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 1d3h pcl4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 1d4h tbpcs1 ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 1d5h tbpcs2 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 1d6h tbpcs3 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ? ? ? ? ? ? ? ? 1d7h tbpcs4 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 * rls6 is reserved for future use. ** currently, rls2 does not create an interrupt, th erefore this bit is not used in t1 mode.
DS26518 8-port t1/e1/j1 transceiver 117 of 286 10.2.3 liu register bit map table 10-8. liu register bit map addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 1000h ltrcr ? rhpm jads1 jads0 japs1 japs0 t1j1e1s lsc 1001h ltipsr tg703 timpton timpl1 timpl0 ? l2 l1 l0 1002h lmcr tais atais lb2 lb1 lb0 tpde rpde te 1003h lrsr ? ? oeq ueq rscs tscs ocs loss 1004h lsimr jaltcim occim sccim loscim jaltsim ocdim scdim losdim 1005h llsr jaltc occ scc losc jalts ocd scd losd 1006h lrsl rsl3 rsl2 rls1 rls0 ? ? ? ? 1007h lrismr ? rimpon ? ? ? rimpm2 rimpm1 rimpm0 1008h lrcr rg703 ? ? ? rtr rmonen rsms1 rsms0 1009h? 101fh test registers ? ? ? ? ? ? ? ?
DS26518 8-port t1/e1/j1 transceiver 118 of 286 10.2.4 bert register bit map table 10-9. bert register bit map addr name bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 1100h bawc acnt7 acnt6 acnt5 acnt4 acnt3 acnt2 acnt1 acnt0 1101h brp1 rpat7 rpat6 rpat5 rpat4 rpat3 rpat2 rpat1 rpat0 1102h brp2 rpat15 rpat14 rpat13 rpat12 rpat11 rpat10 rpat9 rpat8 1103h brp3 rpat23 rpat22 rpat21 rpat20 rpat19 rpat18 rpat17 rpat16 1104h brp4 rpat31 rpat30 rpat29 rpat28 rpat27 rpat26 rpat25 rpat24 1105h bc1 tc tinv rinv ps2 ps1 ps0 lc resync 1106h bc2 eib2 eib1 eib0 sbe rpl3 rpl2 rpl1 rpl0 1107h bbc1 bbc7 bbc6 bbc5 bbc4 bbc3 bbc2 bbc1 bbc0 1108h bbc2 bbc15 bbc14 bbc13 bbc12 bbc11 bbc10 bbc9 bbc8 1109h bbc3 bbc23 bbc22 bbc21 bbc20 bbc19 bbc18 bbc17 bbc16 110ah bbc4 bbc31 bbc30 bbc29 bbc28 bbc27 bbc26 bbc25 bbc24 110bh bec1 ec7 ec6 ec5 ec4 ec3 ec2 ec1 ec0 110ch bec2 ec15 ec14 ec13 ec12 ec11 ec10 ec9 ec8 110dh bec3 ec23 ec22 ec21 ec20 ec19 ec18 ec17 ec16 110eh blsr ? bbed bbco beco bra1 bra0 brlos bsync 110fh bsim ? bbed bbco beco bra1 bra0 brlos bsync
DS26518 8-port t1/e1/j1 transceiver 119 of 286 10.3 global register definitions functions contained in the global registers include: fr amer reset, liu reset, device id, bert interrupt status, framer interrupt status, ibo configurat ion, mclk configuration, and bpclk1 configuration. the global registers bit descriptions are presented below. table 10-10. global register set address name description r/w 00f0h gtcr1 global transceiver control register 1 r/w 00f1h gfcr1 global framer control register 1 r/w 00f2h gtcr3 global transceiver control register 3 r/w 00f3h gtccr1 global transceiver clock control register 1 r/w 00f4h gtccr3 global transceiver clock control register 3 r/w 00f5h ? reserved ? 00f6h gsrr1 global liu software reset register 1 r/w 00f7h ? reserved ? 00f8h idr device identification register r 00f9h gfisr1 global framer interrupt status register 1 r 00fah gbisr1 global bert interrupt status register 1 r 00fbh glisr1 global liu interrupt status register 1 r 00fch gfimr1 global framers interrupt mask register 1 rw 00fdh gbimr1 global bert interrupt mask register 1 rw 00feh glimr1 global liu interrupt mask register 1 rw note 1: reserved registers should only be written with all zeros. note 2: the global registers are located in the framer address space. the corresponding address space for the other seven framers is ?reserved,? and should be initialized with all zeros for proper operation.
DS26518 8-port t1/e1/j1 transceiver 120 of 286 register name gtcr1 register description: global transceiver control register 1 register address: 00f0h bit # 7 6 5 4 3 2 1 0 name gpsel3 gpsel2 gpsel1 ? 528md gibo gcle gipi default 0 0 0 0 0 0 0 0 bits 7 to 5: general-purpose i/o pins select (gpsel[3:1]) table 10-11. output status control gpsel[3:1] rlf/ltc[8:1] al/rsigf/flos[8:1] 000 rlf al 001 ltc al 010 rlf rsigf 011 ltc rsigf 100 rlf flos 101 ltc flos 110 reserved reserved 111 reserved reserved bit 3: ds26528 mode (528md) 0 = normal operation. 1 = pin definitions switch to ds26528 pins to obtain pin compatibility with the ds26528. normal operation 528md rsysclk[8:2] rlf/ltc[8:2] rsysclk1 rsysclk1 clko rlf/ltc1 tsysclk[8:2] al/rsigf/flos[8:2] tsysclk1 tsysclk1 spi_sel al/rsigf/flos1 tsync/tssyncio[8: 1] tsync[8:1] (tie low?unused) tssyncio bit 2: ganged ibo enable (gibo). this bit is used to select either the internal mux for ibo operation or an external ?wire-or? operation. normally this bit should be set = 0 and the internal mux used. 0 = use internal ibo mux. 1 = externally ?wire-or? tsern and rsern for ibo operation. note: setting gibo disables the internal ibo mux. gfcr1 must be set to inform the framers of the ibo configuration. bit 1: global counter latch enable (gcle). a low-to-high transition on this bit will, when enabled, latch the framer performance monitor counters. each framer can be independently enabled to accept this input. this bit must be cleared and set again to perform another counter latch. bit 0: global interrupt pin inhibit (gipi) 0 = normal operation. interrupt pin ( intb ) will toggle low on an unmasked interrupt condition. 1 = interrupt inhibit. interrupt pin ( intb ) is forced high (inactive) when this bit is set.
DS26518 8-port t1/e1/j1 transceiver 121 of 286 register name: gfcr1 description: global framer control register 1 register address: 00f1h bit # 7 6 5 4 3 2 1 0 name iboms1 iboms0 bpclk1 bpclk0 ? rfmss tcbcs rcbcs default 0 0 0 0 0 0 0 0 bits 7 and 6: interleave bus operation mode select 1 and 0 (iboms[1:0]). these bits determine the configuration of the ibo (interleaved bus) multiplexer and inform the framers of the ibo configuration. these bits should be used in conjunction with the rx and tx ibo control regist ers within each of the framer units. these bits control channels 1 to 8. additional information concerning the ibo multiplexer is given in section 9.8.2 . these bits must be set whether using the internal ibo mux or externally ganging the pins. iboms1 iboms0 ibo mode 0 0 ibo disabled. 0 1 2 devices on bus (4.096mhz). 1 0 4 devices on bus (8.192mhz). 1 1 8 devices on bus (16.384mhz). bits 5 and 4: backplane clock select 1 and 0 (bpclk[1:0]). these bits determine the clock frequency output on the bpclk1 pin. bpclk1 bpclk0 bpclk1 frequency 0 0 2.048mhz 0 1 4.096mhz 1 0 8.192mhz 1 1 16.384mhz bit 2: receive frame/multiframe sync select (rfmss). this bit controls the function of all eight rmsyncn/rfsyncn pins. 0 = rmsync/rfsync[8:1] pins output rfsync[8:1] (receive frame sync) 1 = rmsync/rfsync[8:1] pins output rm sync[8:1] (receive multiframe sync) bit 1: transmit channel block/clock select (tcbcs). this bit controls the function of all eight tchblkn/tchclkn pins. 0 = tchblk/tchclk[8:1] pins output tchblk[8:1] (transmit channel block) 1 = tchblk/tchclk[8:1] pins output tchclk[8:1] (transmit channel clock) bit 0: receive channel block/clock select (rcbcs). this bit controls the function of all eight rchblkn/rchclkn pins. 0 = rchblk/rchclk[8:1] pins output rchblk[8:1] (receive channel block) 1 = rchblk/rchclk[8:1] pins output rchclk[8:1] (receive channel clock)
DS26518 8-port t1/e1/j1 transceiver 122 of 286 register name: gtcr3 register description: global transceiver control register 3 register address: 00f2h bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? tssynciosel tsyncsel default 0 0 0 0 0 0 0 0 bit 1: transmit system synchr onization i/o select (tssynciosel) 0 = tssyncio[8:1] are inputs on tsync/tssyncio[8:1] pins 1 = tssyncio[8:1] are output s synchronous to bpclk1. bit 0: tsyncn/tssyncion pin select (tsyncsel) 0 = tsyncn is selected for tsync/tssyncio[8:1] pins 1 = tssyncion is selected for tsync/tssyncio[8:1] pins note: if tsyncn is selected, control of tsyncn (i/o) is via the tiocr register. tssyncion is normally selected when transmit elastic stores are enabled.
DS26518 8-port t1/e1/j1 transceiver 123 of 286 register name: gtccr1 register description: global transceiver clock control register 1 register address: 00f3h bit # 7 6 5 4 3 2 1 0 name bprefsel3 bprefsel2 bprefsel1 bprefse l0 bfreqsel freqsel mps1 mps0 default 0 0 0 0 0 0 0 0 bits 7 to 4: backplane clock reference selects (bprefsel[3:0]). these bits select which reference clock source will be used for bpclk1 generation. the bpclk1 can be generated from liu?s 1 to 8 recovered clocks, an external reference, or derivatives of mclk input. this is shown in table 10-13 . see figure 9-9 for additional information. bit 3: backplane frequency select (bfreqsel). in conjunction with bprfsel[3:0], this bit identifies the reference clock frequency used by the DS26518 backplane clock generation circuit. note that the setting of this bit should match the t1e1 selection for the liu whose recove red clock is being used to generate the backplane clock. see figure 9-9 for additional information. 0 = backplane reference clock is 2.048mhz. 1 = backplane reference clock is 1.544mhz. bit 2: frequency selection (freqsel). in conjunction with the mps[1:0] bits, this bit selects the external mclk frequency of the signal input at the mclk pin of the DS26518. 0 = the external master clock is 2.048mhz or multiple thereof. 1 = the external master clock is 1.544mhz or multiple thereof. bits 1 and 0: master period select 1 and 0 (mps[1:0]). in conjunction with the freqsel bit, these bits select the external mclk frequency of the signal input at the mclk pin of the DS26518. this is shown in table 10-12 . table 10-12. master cl ock input selection freqsel mps1 mps0 mclk (mhz 50ppm) 0 0 0 2.048 0 0 1 4.096 0 1 0 8.192 0 1 1 16.384 1 0 0 1.544 1 0 1 3.088 1 1 0 6.176 1 1 1 12.352
DS26518 8-port t1/e1/j1 transceiver 124 of 286 table 10-13. backplane reference clock select bprefsel3 bprefsel2 bprefsel1 bprefsel0 bfreqsel reference clock source 0 0 0 0 0 2.048mhz rclk1 0 0 0 0 1 1.544mhz rclk1 0 0 0 1 0 2.048mhz rclk2 0 0 0 1 1 1.544mhz rclk2 0 0 1 0 0 2.048mhz rclk3 0 0 1 0 1 1.544mhz rclk3 0 0 1 1 0 2.048mhz rclk4 0 0 1 1 1 1.544mhz rclk4 0 1 0 0 0 2.048mhz rclk5 0 1 0 0 1 1.544mhz rclk5 0 1 0 1 0 2.048mhz rclk6 0 1 0 1 1 1.544mhz rclk6 0 1 1 0 0 2.048mhz rclk7 0 1 1 0 1 1.544mhz rclk7 0 1 1 1 0 2.048mhz rclk8 0 1 1 1 1 1.544mhz rclk8 1 0 0 0 0 2.048mhz derived from mclk. (refclkio is an output.) 1 0 0 0 1 1.544mhz derived from mclk. (refclkio is an output.) 1 0 0 1 0 2.048mhz external clock input at refclkio. (refclkio is an input.) 1 0 0 1 1 1.544mhz external clock input at refclkio. (refclkio is an input.)
DS26518 8-port t1/e1/j1 transceiver 125 of 286 register name: gtccr3 register description: global transceiver clock control register 3 register address: 00f4h bit # 7 6 5 4 3 2 1 0 name ? rsysclksel tsysclksel tclksel clkosel3 clkosel2 clkosel1 clkosel0 default 0 0 0 0 0 0 0 0 bit 6: rsysclkn select (rsysclksel) 0 = use rsysclkn pins for each receive system clock (channels 1?8). 1 = use bpclk1 as the master clock for all eight receive system clocks (channels 1?8). bit 5: tsysclkn sele ct (tsysclksel) 0 = use tsysclkn pins for each tr ansmit system cl ock (channels 1?8). 1 = use bpclk1 as the master clock for all eight transmit system clocks (channels 1?8). bit 4: tclkn select (tclksel) 0 = use tclkn pins for each of the transmit clock (channels 1?8). 1 = use refclkio as the master clock for all eight transmit clocks (channels 1?8). bits 3 to 0: clock out frequency select (clkosel[3:0]. clko output pin will use mclk (1.544mhz or 2.048mhz or scaled version) as its reference. the follow ing table shows how to configure for each frequency. for best jitter performance use a 2.048mhz oscillator for mclk. clkosel[3:0] clko (khz) 0000 2048 0001 4096 0010 8192 0011 16384 0100 1544 0101 3088 0110 6176 0111 12352 1000 1536 1001 3072 1010 6144 1011 12288 1100 32 1101 64 1110 128 1111 256
DS26518 8-port t1/e1/j1 transceiver 126 of 286 register name: gsrr1 register description: global liu software reset register 1 register address: 00f6h bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? lrst brst frst default 0 0 0 0 0 0 0 0 bit 2: liu software reset (lrst). liu channels 1?8 logic and registers are reset with a 0-to-1 transition in this bit. the reset is released when a zero is written to this bit. 0 = normal operation. 1 = reset liu channels 1?8. bit 1: bert software reset (brst). bert channels 1?8 logic and registers are reset with a 0-to-1 transition in this bit. the reset is released when a zero is written to this bit. 0 = normal operation. 1 = reset bert channels 1?8. bit 0: framer software reset (frst). framers 1-8 to logic and registers are reset with a 0-to-1 transition in this bit. the reset is released when a zero is written to this bit. 0 = normal operation. 1 = reset framers 1?8. register name: idr register description: device identification register register address: 00f8h bit # 7 6 5 4 3 2 1 0 name id7 id6 id5 id4 id3 id2 id1 id0 default 1 1 0 1 0 0 0 0 bits 7 to 3: device id (id[7:3]). the upper five bits of the idr are used to display the DS26518 id. table 10-14. device id codes in this product family device id7 id6 id5 id4 id3 ds26519 1 1 0 1 1 DS26518 1 1 0 1 0 ds26528 0 1 0 1 1 ds26524 0 1 1 0 0 ds26522 0 1 1 0 1 ds26521 0 1 1 1 0 bits 2 to 0: silicon revision bits (id[2:0]). the lower three bits of the idr are used to display a sequential number denoting the die revision of the chip. the initial s ilicon revision = ?000? and is incremented with each silicon revision. this value is not the same as the two-character device revision on the top brand of the device. this is due to the fact that portions of the device assembly other than the silicon ma y change, causing the device revision increment on the brand without having a revision of the s ilicon. id0 is the lsb of a decimal code that represents the chip revision.
DS26518 8-port t1/e1/j1 transceiver 127 of 286 register name: gfisr1 register description: global framer interrupt status register 1 register address: 00f9h bit # 7 6 5 4 3 2 1 0 name fis8 fis7 fis6 fis5 fis4 fis3 fis2 fis1 default 0 0 0 0 0 0 0 0 the gfisr1 register reports the framer interrupt status for the t1/e1 framers of channels 1 to 8. a logic one in the associated bit location indicates a fram er has set its interrupt signal. bit 7: framer interrupt status 8 (fis8) 0 = framer 8 has not issued an interrupt. 1 = framer 8 has issued an interrupt. bit 6: framer interrupt status 7 (fis7) 0 = framer 7 has not issued an interrupt. 1 = framer 7 has issued an interrupt. bit 5: framer interrupt status 6 (fis6) 0 = framer 6 has not issued an interrupt. 1 = framer 6 has issued an interrupt. bit 4: framer interrupt status 5 (fis5) 0 = framer 5 has not issued an interrupt. 1 = framer 5 has issued an interrupt. bit 3: framer interrupt status 4 (fis4) 0 = framer 4 has not issued an interrupt. 1 = framer 4 has issued an interrupt. bit 2: framer interrupt status 3 (fis3) 0 = framer 3 has not issued an interrupt. 1 = framer 3 has issued an interrupt. bit 1: framer interrupt status 2 (fis2) 0 = framer 2 has not issued an interrupt. 1 = framer 2 has issued an interrupt. bit 0: framer interrupt status 1 (fis1) 0 = framer 1 has not issued an interrupt. 1 = framer 1 has issued an interrupt.
DS26518 8-port t1/e1/j1 transceiver 128 of 286 register name: gbisr1 register description: global bert interrupt status register 1 register address: 00fah bit # 7 6 5 4 3 2 1 0 name bis8 bis7 bis6 bis5 bis4 bis3 bis2 bis1 default 0 0 0 0 0 0 0 0 the gbisr1 register reports the interrupt status for the t1/e1 bit error rate testers (bert) of channels 1 to 8. a logic one in the associated bit location indi cates a bert has set its interrupt signal. bit 7: bert interrupt status 8 (bis8) 0 = bert 8 has not issued an interrupt. 1 = bert 8 has issued an interrupt. bit 6: bert interrupt status 7 (bis7) 0 = bert 7 has not issued an interrupt. 1 = bert 7 has issued an interrupt. bit 5: bert interrupt status 6 (bis6) 0 = bert 6 has not issued an interrupt. 1 = bert 6 has issued an interrupt. bit 4: bert interrupt status 5 (bis5) 0 = bert 5 has not issued an interrupt. 1 = bert 5 has issued an interrupt. bit 3: bert interrupt status 4 (bis4) 0 = bert 4 has not issued an interrupt. 1 = bert 4 has issued an interrupt. bit 2: bert interrupt status 3 (bis3) 0 = bert 3 has not issued an interrupt. 1 = bert 3 has issued an interrupt. bit 1: bert interrupt status 2 (bis2) 0 = bert 2 has not issued an interrupt. 1 = bert 2 has issued an interrupt. bit 0: bert interrupt status 1 (bis1) 0 = bert 1 has not issued an interrupt. 1 = bert 1 has issued an interrupt.
DS26518 8-port t1/e1/j1 transceiver 129 of 286 register name: glisr1 register description: global liu interrupt status register 1 register address: 00fbh bit # 7 6 5 4 3 2 1 0 name lis8 lis7 lis6 lis5 lis4 lis3 lis2 lis1 default 0 0 0 0 0 0 0 0 the glisr1 register reports the liu in terrupt status for the t1/e1 lius of channels 1 to 8. a logic one in the associated bit location indicates a li u has set its interrupt signal. bit 7: liu interrupt status 8 (lis8) 0 = liu 8 has not issued an interrupt. 1 = liu 8 has issued an interrupt. bit 6: liu interrupt status 7 (lis7) 0 = liu 7 has not issued an interrupt. 1 = liu 7 has issued an interrupt. bit 5: liu interrupt status 6 (lis6) 0 = liu 6 has not issued an interrupt. 1 = liu 6 has issued an interrupt. bit 4: liu interrupt status 5 (lis5) 0 = liu 5 has not issued an interrupt. 1 = liu 5 has issued an interrupt. bit 3: liu interrupt status 4 (lis4) 0 = liu 4 has not issued an interrupt. 1 = liu 4 has issued an interrupt. bit 2: liu interrupt status 3 (lis3) 0 = liu 3 has not issued an interrupt. 1 = liu 3 has issued an interrupt. bit 1: liu interrupt status 2 (lis2) 0 = liu 2 has not issued an interrupt. 1 = liu 2 has issued an interrupt. bit 0: liu interrupt status 1 (lis1) 0 = liu 1 has not issued an interrupt. 1 = liu 1 has issued an interrupt.
DS26518 8-port t1/e1/j1 transceiver 130 of 286 register name: gfimr1 register description: global framer interrupt mask register 1 register address: 00fch bit # 7 6 5 4 3 2 1 0 name fim8 fim7 fim6 fim5 fim4 fim3 fim2 fim1 default 0 0 0 0 0 0 0 0 bit 7: framer 8 interrupt mask (fim8) 0 = interrupt masked. 1 = interrupt enabled. bit 6: framer 7 interrupt mask (fim7) 0 = interrupt masked. 1 = interrupt enabled. bit 5: framer 6 interrupt mask (fim6) 0 = interrupt masked. 1 = interrupt enabled. bit 4: framer 5 interrupt mask (fim5) 0 = interrupt masked. 1 = interrupt enabled. bit 3: framer 4 interrupt mask (fim4) 0 = interrupt masked. 1 = interrupt enabled. bit 2: framer 3 interrupt mask (fim3) 0 = interrupt masked. 1 = interrupt enabled. bit 1: framer 2 interrupt mask (fim2) 0 = interrupt masked. 1 = interrupt enabled. bit 0: framer 1 interrupt mask (fim1) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 131 of 286 register name: gbimr1 register description: global bert interrupt mask register 1 register address: 00fdh bit # 7 6 5 4 3 2 1 0 name bim8 bim7 bim6 bim5 bim4 bim3 bim2 bim1 default 0 0 0 0 0 0 0 0 bit 7: bert interrupt mask 8 (bim8) 0 = interrupt masked. 1 = interrupt enabled. bit 6: bert interrupt mask 7 (bim7) 0 = interrupt masked. 1 = interrupt enabled. bit 5: bert interrupt mask 6 (bim6) 0 = interrupt masked. 1 = interrupt enabled. bit 4: bert interrupt mask 5 (bim5) 0 = interrupt masked. 1 = interrupt enabled. bit 3: bert interrupt mask 4 (bim4) 0 = interrupt masked. 1 = interrupt enabled. bit 2: bert interrupt mask 3 (bim3) 0 = interrupt masked. 1 = interrupt enabled. bit 1: bert interrupt mask 2 (bim2) 0 = interrupt masked. 1 = interrupt enabled. bit 0: bert interrupt mask 1 (bim1) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 132 of 286 register name: glimr1 register description: global liu interrupt mask register 1 register address: 00feh bit # 7 6 5 4 3 2 1 0 name lim8 lim7 lim6 lim5 lim4 lim3 lim2 lim1 default 0 0 0 0 0 0 0 0 bit 7: liu interrupt mask 8 (lim8) 0 = interrupt masked. 1 = interrupt enabled. bit 6: liu interrupt mask 7 (lim7) 0 = interrupt masked. 1 = interrupt enabled. bit 5: liu interrupt mask 6 (lim6) 0 = interrupt masked. 1 = interrupt enabled. bit 4: liu interrupt mask 5 (lim5) 0 = interrupt masked. 1 = interrupt enabled. bit 3: liu interrupt mask 4 (lim4) 0 = interrupt masked. 1 = interrupt enabled. bit 2: liu interrupt mask 3 (lim3) 0 = interrupt masked. 1 = interrupt enabled. bit 1: liu interrupt mask 2 (lim2) 0 = interrupt masked. 1 = interrupt enabled. bit 0: liu interrupt mask 1 (lim1) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 133 of 286 10.4 framer register descriptions 10.4.1 receive register descriptions see table 10-3 for the complete framer register list. register name: rhc register description: receive hdlc control register register address: 010h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rcrcd rhr rhms rhcs4 rhcs3 rhcs2 rhcs1 rhcs0 default 0 0 0 0 0 0 0 0 bit 7: receive crc-16 display (rcrcd) 0 = do not write received crc-16 code to fifo (default). 1 = write received crc-16 code to fifo after last octet of packet. bit 6: receive hdlc reset (rhr). will reset the receive hdlc controller and flush the receive fifo. note that this bit is a acknowledged reset. the host should set this bit and the DS26518 will clear it once the reset operation is complete. the DS26518 will complete the hdlc reset within 2 frames. 0 = normal operation. 1 = reset receive hdlc controller and flush the receive fifo. bit 5: receive hdlc mapping select (rhms) 0 = receive hdlc assigned to channels. 1 = receive hdlc assigned to fdl (t1 mode), sa bits (e1 mode). bits 4 to 0: receive hdlc channel select 4 to 0 (rhcs[4:0]). these bits determine which ds0 is mapped to the hdlc controller when enabled with rhms = 0. rhcs[4:0] = all 0s selects channel 1, rhcs[4:0] = all 1s selects channel 32 (e1). a change to the receive hdlc chan nel select is acknowledged only after a receive hdlc reset (rhr).
DS26518 8-port t1/e1/j1 transceiver 134 of 286 register name: rhbse register description: receive hdlc bit suppress register register address: 011h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name bse8 bse7 bse6 bse5 bse4 bse3 bse2 bse1 default 0 0 0 0 0 0 0 0 bit 7: receive channel bit 8 suppress (bse8). msb of the channel. set to one to stop this bit from being used. bit 6: receive channel bit 7 suppress (bse7). set to one to stop this bit from being used. bit 5: receive channel bit 6 suppress (bse6). set to one to stop this bit from being used. bit 4: receive channel bit 5 suppress (bse5). set to one to stop this bit from being used. bit 3: receive channel bit 4 suppress (bse4). set to one to stop this bit from being used. bit 2: receive channel bit 3 suppress (bse3). set to one to stop this bit from being used. bit 1: receive channel bit 2 suppress (bse2). set to one to stop this bit from being used. bit 0: receive channel bit 1 suppress (bse1). lsb of the channel. set to one to stop this bit from being used.
DS26518 8-port t1/e1/j1 transceiver 135 of 286 register name: rds0sel register description: receive channel monitor select register register address: 012h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? rcm4 rcm3 rcm2 rcm1 rcm0 default 0 0 0 0 0 0 0 0 bits 4 to 0: receive channel monitor bits (rcm[4:0]). rcm0 is the lsb of a 5-bit channel select that determines which receive ds 0 channel data will appear in the rds0m register. register name: rsigc register description: receive-signaling control register register address: 013h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? rfsa1 ? rsff rsfe rsie ? ? ? casms ? rsff rsfe rsie default 0 0 0 0 0 0 0 0 bit 4 (t1 mode): receive force signaling all ones (rfsa1) 0 = do not force robbed bit signaling to all ones. 1 = force signaling bits to all ones on a per-channel basis according to the t1rsaoi1 ?3 registers. bit 4 (e1 mode): cas mode select (casms) 0 = the DS26518 will initiate a resync when two co nsecutive multiframe alignment signals have been received with an error. 1 = the DS26518 will initiate a resync when two co nsecutive multiframe alignment signals have been received with an error, or 1 multiframe has been receiv ed with all the bits in time slot 16 in state 0. alignment criteria is met when at least one bit in st ate 1 is present in the time slot 16 preceding the multiframe alignment signal first det ected (g.732 alternate criteria). bit 2: receive-signaling force freeze (rsff). freezes receive-side signaling at rsign (and rsern if receive- signaling reinsertion is enabled); will ov erride receive free ze enable (rfe). 0 = do not force a freeze event. 1 = force a freeze event. bit 1: receive-signaling freeze enable (rsfe) 0 = no freezing of receive signaling data will occur. 1 = allow freezing of receive signaling data at rs ign (and rsern if receive-signaling reinsertion is enabled). bit 0: receive-signaling integration enable (rsie) 0 = signaling changes of state reported on any change in selected channels. 1 = signaling must be stable for three multiframe s in order for a change of state to be reported.
DS26518 8-port t1/e1/j1 transceiver 136 of 286 register name: t1rcr2 (t1 mode) register description: receive control register 2 register address: 014h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? rslc96 oof2 oof1 raiie rrais default 0 0 0 0 0 0 0 0 bit 4: receive slc-96 synchronizer enable (rslc96). see section 9.9.4.4 for slc-96 details. 0 = the slc-96 synchronizer is disabled. 1 = the slc-96 synchronizer is enabled. bits 3 and 2: out of frame select bits (oof[2:1]) oof2 oof1 out of frame criteria 0 0 2/4 frame bits in error 0 1 2/5 frame bits in error 1 0 2/6 frame bits in error 1 1 2/6 frame bits in error bit 1: receive rai integration enable (raiie). the esf rai indication can be interrupted for a period not to exceed 100ms per interruption (t1.403). in esf mode, se tting raiie will cause the rai status from the DS26518 to be integrated for 200ms. 0 = rai detects when 16 consecutive patterns of 00ff appear in the fdl. rai clears when 14 or fewer patterns of 00ff hex out of 16 possible appear in the fdl. 1 = rai detects when the condition has been present for greater than 200ms. rai clears when the condition has been absent for greater than 200ms. bit 0: receive-side remote alarm select (rrais) 0 = receive framer detects t1 remote alarm. d4?zeros in bit 2 of all channels. esf?00ff pattern in fdl. 1 = receive framer detects j1 remote alarm. d4?a one in the s-bit position of frame 12. esf?all ones in fdl.
DS26518 8-port t1/e1/j1 transceiver 137 of 286 register name: e1rsaimr (e1 mode only) register description: receive sa bit interrupt mask register register address: 014h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? rsa4im rsa5i m rsa6im rsa7im rsa8im default 0 0 0 0 0 0 0 0 bit 4: sa4 change detect interrupt mask (rsa4im). this bit will enable the change detect interrupt for the sa4 bits. any change of state of the sa4 bit will then generate an interrupt in rls7.0 to indicate the change of state. 0 = interrupt masked. 1 = interrupt enabled. bit 3: sa5 change detect interrupt mask (rsa5im). this bit will enable the change detect interrupt for the sa5 bits. any change of state of the sa5 bit will then generate an interrupt in rls7.0 to indicate the change of state. 0 = interrupt masked. 1 = interrupt enabled. bit 2: sa6 change detect interrupt mask (rsa6im). this bit will enable the change detect interrupt for the sa6 bits. any change of state of the sa6 bit will then generate an interrupt in rls7.0 to indicate the change of state. 0 = interrupt masked. 1 = interrupt enabled. bit 1: sa7 change detect interrupt mask (rsa7im). this bit will enable the change detect interrupt for the sa7 bits. any change of state of the sa7 bit will then generate an interrupt in rls7.0 to indicate the change of state. 0 = interrupt masked. 1 = interrupt enabled. bit 0: sa8 change detect interrupt mask (rsa8im). this bit will enable the change detect interrupt for the sa8 bits. any change of state of the sa8 bit will then generate an interrupt in rls7.0 to indicate the change of state. 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 138 of 286 register name: t1rbocc (t1 mode only) register description: receive boc control register register address: 015h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rbr ? rbd1 rbd0 ? rbf1 rbf0 ? default 0 0 0 0 0 0 0 0 bit 7: receive boc reset (rbr). the host should set this bit to force a reset of the boc circuitry. note that this is an acknowledged reset?that is, the host needs only to set the bit and the DS26518 will clear it once the reset operation is complete (less than 250 s). modifications to the rbf[1:0] and rb d[1:0] bits will not be applied to the boc controller until a boc reset has been completed. bits 5 and 4: receive boc disintegration bits (rbd[1:0]). the boc disintegration filter sets the number of message bits that must be received without a valid boc to set the bc bit indicating that a valid boc is no longer being received. rbd1 rbd0 consecutive message bits for boc clear identification 0 0 16 0 1 32 1 0 48 1 1 64 (see note 1) bits 2 and 1: receive boc filter bits (rbf[1:0). the boc filter sets the number of consecutive patterns that must be received without error prior to an indication of a valid message. rbf1 rbf0 consecutive boc codes for valid sequence identification 0 0 none 0 1 3 1 0 5 1 1 7 (see note 1) note 1: the DS26518?s boc controller does not integrate and disintegrate c oncurrently. therefore, if the maximum integration time and the maximum disintegration time are used together, boc messages that repeat fewer than 11 times may not be detected. register name: ridr1 to ridr32 register description: receive idle code definition registers 1 to 32 register address: 020h to 03fh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 bits 7 to 0: per-channel idle code bits (c[7:0]). c0 is the lsb of the code (this bit is transmitted last). address 20h is for channel 1. address 37h is for channel 24. addr ess 3fh is for channel 32. ridr25?ridr32 are e1 mode only.
DS26518 8-port t1/e1/j1 transceiver 139 of 286 register name: t1rsaoi1, t1rsaoi2, t1rsaoi3 (t1 mode only) register description: receive-signaling all-ones insertion registers 1 to 3 register address: 038h, 039h, 03ah + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 t1rsaoi1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 t1rsaoi2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 t1rsaoi3 setting any of the ch[1:24] bits in the t1rsaoi1 to t1r saoi3 registers will cause signaling data to be replaced with logic ones as reported on rsern. the rsign signal will continue to report received signaling data. note that this feature must be enabled with control bit rsigc .4. register name: t1rdmwe1, t1rdmwe2, t1rdmwe3 register description: t1 receive digital milliwatt enable registers 1 to 3 register address: 03ch, 03dh, 03eh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 t1rdmwe1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 t1rdmwe2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 t1rdmwe3 bits 7 to 0: receive digital milliwatt enable for channels 1 to 24 (ch[1:24]) 0 = does not affect the receive data associated with this channel. 1 = replace the receive data associated with this channel with digital milliwatt code.
DS26518 8-port t1/e1/j1 transceiver 140 of 286 register name: rs1 to rs16 register description: receive-signaling registers 1 to 16 register address: 040h to 04fh + (200h x (n - 1)) : where n = 1 to 8 t1 mode: (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch1-a ch1-b ch1-c ch1-d ch13-a ch13-b ch13-c ch13-d rs1 ch2-a ch2-b ch2-c ch2-d ch14-a ch14-b ch14-c ch14-d rs2 ch3-a ch3-b ch3-c ch3-d ch15-a ch15-b ch15-c ch15-d rs3 ch4-a ch4-b ch4-c ch4-d ch16-a ch16-b ch16-c ch16-d rs4 ch5-a ch5-b ch5-c ch5-d ch17-a ch17-b ch17-c ch17-d rs5 ch6-a ch6-b ch6-c ch6-d ch18-a ch18-b ch18-c ch18-d rs6 ch7-a ch7-b ch7-c ch7-d ch19-a ch19-b ch19-c ch19-d rs7 ch8-a ch8-b ch8-c ch8-d ch20-a ch20-b ch20-c ch20-d rs8 ch9-a ch9-b ch9-c ch9-d ch21-a ch21-b ch21-c ch21-d rs9 ch10-a ch10-b ch10- c ch10-d ch22-a ch22-b ch22-c ch22-d rs10 ch11-a ch11-b ch11- c ch11-d ch23-a ch23-b ch23-c ch23-d rs11 ch12-a ch12-b ch12- c ch12-d ch24-a ch24-b ch24-c ch24-d rs12 e1 mode: (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name 0 0 0 0 x y x x rs1 ch1-a ch1-b ch1-c ch1-d ch16-a ch16-b ch16-c ch16-d rs2 ch2-a ch2-b ch2-c ch2-d ch17-a ch17-b ch17-c ch17-d rs3 ch3-a ch3-b ch3-c ch3-d ch18-a ch18-b ch18-c ch18-d rs4 ch4-a ch4-b ch4-c ch4-d ch19-a ch19-b ch19-c ch19-d rs5 ch5-a ch5-b ch5-c ch5-d ch20-a ch20-b ch20-c ch20-d rs6 ch6-a ch6-b ch6-c ch6-d ch21-a ch21-b ch21-c ch21-d rs7 ch7-a ch7-b ch7-c ch7-d ch22-a ch22-b ch22-c ch22-d rs8 ch8-a ch8-b ch8-c ch8-d ch23-a ch23-b ch23-c ch23-d rs9 ch9-a ch9-b ch9-c ch9-d ch24-a ch24-b ch24-c ch24-d rs10 ch10-a ch10-b ch10- c ch10-d ch25-a ch25-b ch25-c ch25-d rs11 ch11-a ch11-b ch11- c ch11-d ch26-a ch26-b ch26-c ch26-d rs12 ch12-a ch12-b ch12- c ch12-d ch27-a ch27-b ch27-c ch27-d rs13 ch13-a ch13-b ch13- c ch13-d ch28-a ch28-b ch28-c ch28-d rs14 ch14-a ch14-b ch14- c ch14-d ch29-a ch29-b ch29-c ch29-d rs15 ch15-a ch15-b ch15- c ch15-d ch30-a ch30-b ch30-c ch30-d rs16 in the esf framing mode, there can be up to four signaling bits per channel (a, b, c, and d). in the d4 framing mode, there are only two signaling bits per channel (a and b) . in the d4 framing mode, the framer will repeat the a and b signaling data in the c and d bit locations. therefore, when the framer is operated in d4 framing mode, the user will need to retrieve the signaling bits every 1. 5ms as opposed to 3ms for esf mode. the receive-signaling registers are frozen and not updated during a loss of sync condition. they will contain the most recent signaling information before the ?oof? occurred.
DS26518 8-port t1/e1/j1 transceiver 141 of 286 register name: lcvcr1 register description: line code violation count register 1 register address: 050h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name lcvc15 lcvc14 lcvc13 lcvc 12 lcvc11 lcvc10 lcvc9 lcvc8 default 0 0 0 0 0 0 0 0 bits 7 to 0: line code violation counter bits 15 to 8 (lcvc[15:8]). lcv15 is the msb of the 16-bit code violation count. register name: lcvcr2 register description: line code violation count register 2 register address: 051h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name lcvc7 lcvc6 lcvc5 lcvc 4 lcvc3 lcvc2 lcvc1 lcvc0 default 0 0 0 0 0 0 0 0 bits 7 to 0: line code violation counter bits 7 to 0 (lcvc[7:0]). lcv0 is the lsb of the 16-bit code violation count. register name: pcvcr1 register description: path code violation count register 1 register address: 052h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name pcvc15 pcvc14 pcvc13 pcvc12 pcvc11 pcvc10 pcvc9 pcvc8 default 0 0 0 0 0 0 0 0 bits 7 to 0: path code violation counter bits 15 to 8 (pcvc[15:8]). pcvc15 is the msb of the 16-bit path code violation count. register name: pcvcr2 register description: path code violation count register 2 register address: 053h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name pcvc7 pcvc6 pcvc5 pcvc 4 pcvc3 pcvc2 pcvc1 pcvc0 default 0 0 0 0 0 0 0 0 bits 7 to 0: path code violation counter bits 7 to 0 (pcvc[7:0]). pcvc0 is the lsb of the 16-bit path code violation count.
DS26518 8-port t1/e1/j1 transceiver 142 of 286 register name: foscr1 register description: frames out of sync count register 1 register address: 054h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name fos15 fos14 fos13 fos12 fos11 fos10 fos9 fos8 default 0 0 0 0 0 0 0 0 bits 7 to 0: frames out of sync counter bits 15 to 8 (fos[15:8]). fos15 is the msb of the 16-bit frames out of sync count. register name: foscr2 register description: frames out of sync count register 2 register address: 055h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name fos7 fos6 fos5 fos4 fos3 fos2 fos1 fos0 default 0 0 0 0 0 0 0 0 bits 7 to 0: frames out of sync counter bits 7 to 0 (fos[7:0]). fos0 is the lsb of the 16-bit frames out of sync count. register name: e1ebcr1 (e1 mode only) register description: e-bit count register 1 register address: 056h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name eb15 eb14 eb13 eb12 eb11 eb10 eb9 eb8 default 0 0 0 0 0 0 0 0 bits 7 to 0: e-bit counter bits 15 to 8 (eb[15:8]). eb15 is the msb of the 16-bit e-bit count. register name: e1ebcr2 (e1 mode only) register description: e-bit count register 2 register address: 057h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name eb7 eb6 eb5 eb4 eb3 eb2 eb1 eb0 default 0 0 0 0 0 0 0 0 bits 7 to 0: e-bit counter bits 7 to 0 (eb[7:0]). eb0 is the lsb of the 16-bit e-bit count.
DS26518 8-port t1/e1/j1 transceiver 143 of 286 register name: feacr1 register description: error count a register 1 register address: 058h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name feacr15 feacr14 feacr13 feacr1 2 feacr11 feacr10 feacr9 feacr8 default 0 0 0 0 0 0 0 0 bits 7 to 0: error count a register 1 bits 15 to 8 (feacr[15:8]). feacr15 is the msb of the 16-bit far end a counter. register name: feacr2 register description: error count a register 2 register address: 059h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name feacr7 feacr6 feacr5 feacr4 feacr3 feacr2 feacr1 feacr0 default 0 0 0 0 0 0 0 0 bits 7 to 0: error count a register 2 bits 7 to 0 (feacr[7:0]). feacr0 is the lsb of the 16-bit far end a counter. register name: febcr1 register description: error count b register 1 register address: 05ah + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name febcr15 febcr14 febcr13 febcr1 2 febcr11 febcr10 febcr9 febcr8 default 0 0 0 0 0 0 0 0 bits 7 to 0: error count b register 1 bits 15 to 8 (febcr[15:8]). febcr15 is the msb of the 16-bit far end error b counter. register name: febcr2 register description: error count b register 2 register address: 05bh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name febcr7 febcr6 febcr5 febcr4 febcr3 febcr2 febcr1 febcr0 default 0 0 0 0 0 0 0 0 bits 7 to 0: error count b register 2 bits 7 to 0 (febcr[7:0]). febcr0 is the lsb of the 16-bit far end error b counter.
DS26518 8-port t1/e1/j1 transceiver 144 of 286 register name: rds0m register description: receive ds0 monitor register register address: 060h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name b1 b2 b3 b4 b5 b6 b7 b8 default 0 0 0 0 0 0 0 0 bits 7 to 0: receive ds0 channel bits (b[1:8]). receive channel data that has been selected by the receive channel monitor select register ( rds0sel ). b8 is the lsb of the ds0 channel (last bit to be received).
DS26518 8-port t1/e1/j1 transceiver 145 of 286 register name: t1rfdl (t1 mode) register description: receive fdl register register address: 062h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rfdl7 rfdl6 rfdl5 rfd l4 rfdl3 rfdl2 rfdl1 rfdl0 default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for e1 mode. see e1rrts7 . bit 7: receive fdl bit 7 (rfdl7). msb of the received fdl code. bit 6: receive fdl bit 6 (rfdl6). bit 5: receive fdl bit 5 (rfdl5). bit 4: receive fdl bit 4 (rfdl4). bit 3: receive fdl bit 3 (rfdl3). bit 2: receive fdl bit 2 (rfdl2). bit 1: receive fdl bit 1 (rfdl1). bit 0: receive fdl bit 0 (rfdl0). lsb of the received fdl code. register name: e1rrts7 (e1 mode) register description: receive real-time status register 7 register address: 062h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name csc5 csc4 csc3 csc2 csc0 crc4sa cassa fassa default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for t1 mode. see t1rfdl . all bits in this register are real-time (not latched). bits 7 to 3: crc-4 sync counter bits (csc[5:2] and csc0). the crc-4 sync counter increments each time the 8ms crc-4 multiframe search times out. the counter is cleared when the framer has successfully obtained synchronization at the crc-4 leve l. the counter can also be cleared by disabling the crc-4 mode ( rcr1 .3 = 0). this counter is useful for determining the amount of time the framer has been searching for synchronization at the crc-4 level. itu-t g.706 suggests t hat if synchronization at the crc-4 level cannot be obtained within 400 ms, then the search should be abandoned and proper action taken. the crc-4 sync counter will saturate (not rollover). csc0 is the lsb of the 6?bit counter. (note: csc1 is omitted to allow resolution to > 400ms using 5 bits.) bit 2: crc-4 mf sync active (crc4sa). set while the synchronizer is se arching for the crc-4 mf alignment word. bit 1: cas mf sync active (cassa). set while the synchronizer is searching for the cas mf alignment word. bit 0: fas sync active (fassa). set while the synchronizer is search ing for alignment at the fas level.
DS26518 8-port t1/e1/j1 transceiver 146 of 286 register name: t1rboc (t1 mode) register description: receive boc register register address: 63h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? rboc5 rboc4 rboc3 rboc2 rboc1 rboc0 default 0 0 0 0 0 0 0 0 bit 5: boc bit 5 (rboc5) bit 4: boc bit 4 (rboc4) bit 3: boc bit 3 (rboc3) bit 2: boc bit 2 (rboc2) bit 1: boc bit 1 (rboc1) bit 0: boc bit 0 (rboc0) the t1rboc register always contains the last valid boc received. the receive fdl register ( t1rfdl ) reports the incoming facility data link (fdl) or the incoming fs bi ts. the lsb is received first. in d4 framing mode, rfdl updates on multiframe boundaries and reports the six fs bits in rfdl[5:0].
DS26518 8-port t1/e1/j1 transceiver 147 of 286 register name: t1rslc1, t1rslc2, t1rslc3 (t1 mode) register description: receive slc96 data link registers register address: 064h, 065h, 066h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name c8 c7 c6 c5 c4 c3 c2 c1 t1rslc1 m2 m1 s=0 s=1 s=0 c11 c10 c9 t1rslc2 s=1 s4 s3 s2 s1 a2 a1 m3 t1rslc3 note: these registers have an alternate definition for e1 mode. see e1raf , e1rnaf , and e1rsiaf . register name: e1raf (e1 mode) register description: e1 receive align frame register register address: 064h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name si 0 0 1 1 0 1 1 default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for t1 mode. see t1rslc1 . bit 7: international bit (si) bit 6: frame alignment signal bit (0) bit 5: frame alignment signal bit (0) bit 4: frame alignment signal bit (1) bit 3: frame alignment signal bit (1) bit 2: frame alignment signal bit (0) bit 1: frame alignment signal bit (1) bit 0: frame alignment signal bit (1)
DS26518 8-port t1/e1/j1 transceiver 148 of 286 register name: e1rnaf (e1 mode) register description: e1 receive non-align frame register register address: 065h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name si 1 a sa4 sa5 sa6 sa7 sa8 default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for t1 mode. see t1rslc2 . bit 7: international bit (si) bit 6: frame non-alignment signal bit (1) bit 5: remote alarm (a) bit 4: additional bit 4 (sa4) bit 3: additional bit 5 (sa5) bit 2: additional bit 6 (sa6) bit 1: additional bit 7 (sa7) bit 0: additional bit 8 (sa8) register name: e1rsiaf (e1 mode) register description: received si bits of the align frame register address: 066h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name sif14 sif12 sif10 sif8 sif6 sif4 sif2 sif0 default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for t1 mode. see t1rslc3 . bit 7: si bit of frame 14 (sif14) bit 6: si bit of frame 12 (sif12) bit 5: si bit of frame 10 (sif10) bit 4: si bit of frame 8 (sif8) bit 3: si bit of frame 6 (sif6) bit 2: si bit of frame 4 (sif4) bit 1: si bit of frame 2 (sif2) bit 0: si bit of frame 0 (sif0)
DS26518 8-port t1/e1/j1 transceiver 149 of 286 register name: e1rsinaf (e1 mode only) register description: receive si bits of the non-align frame register register address: 067h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name sif15 sif13 sif11 sif9 sif7 sif5 sif3 sif1 default 0 0 0 0 0 0 0 0 bit 7: si bit of frame 15 (sif15) bit 6: si bit of frame 13 (sif13) bit 5: si bit of frame 11 (sif11) bit 4: si bit of frame 9 (sif9) bit 3: si bit of frame 7 (sif7) bit 2: si bit of frame 5 (sif5) bit 1: si bit of frame 3 (sif3) bit 0: si bit of frame 1 (sif1) register name: e1rra (e1 mode only) register description: receive remote alarm register register address: 068h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rraf15 rraf13 rraf11 rraf9 rraf7 rraf5 rraf3 rraf1 default 0 0 0 0 0 0 0 0 bit 7: remote alarm bit of frame 15 (rraf15) bit 6: remote alarm bit of frame 13 (rraf13) bit 5: remote alarm bit of frame 11 (rraf11) bit 4: remote alarm bit of frame 9 (rraf9) bit 3: remote alarm bit of frame 7 (rraf7) bit 2: remote alarm bit of frame 5 (rraf5) bit 1: remote alarm bit of frame 3 (rraf3) bit 0: remote alarm bit of frame 1 (rraf1)
DS26518 8-port t1/e1/j1 transceiver 150 of 286 register name: e1rsa4 (e1 mode only) register description: received sa4 bits register register address: 069h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rsa4f15 rsa4f13 rsa4f11 rsa4f 9 rsa4f7 rsa4f5 rsa4f3 rsa4f1 default 0 0 0 0 0 0 0 0 bit 7: sa4 bit of frame 15 (rsa4f15) bit 6: sa4 bit of frame 13 (rsa4f13) bit 5: sa4 bit of frame 11 (rsa4f11) bit 4: sa4 bit of frame 9 (rsa4f9) bit 3: sa4 bit of frame 7 (rsa4f7) bit 2: sa4 bit of frame 5 (rsa4f5) bit 1: sa4 bit of frame 3 (rsa4f3) bit 0: sa4 bit of frame 1 (rsa4f1) register name: e1rsa5 (e1 mode only) register description: received sa5 bits register register address: 06ah + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rsa5f15 rsa5f13 rsa5f11 rsa5f 9 rsa5f7 rsa5f5 rsa5f3 rsa5f1 default 0 0 0 0 0 0 0 0 bit 7: sa5 bit of frame 15 (rsa5f15) bit 6: sa5 bit of frame 13 (rsa5f13) bit 5: sa5 bit of frame 11 (rsa5f11) bit 4: sa5 bit of frame 9 (rsa5f9) bit 3: sa5 bit of frame 7 (rsa5f7) bit 2: sa5 bit of frame 5 (rsa5f5) bit 1: sa5 bit of frame 3 (rsa5f3) bit 0: sa5 bit of frame 1 (rsa5f1)
DS26518 8-port t1/e1/j1 transceiver 151 of 286 register name: e1rsa6 (e1 mode only) register description: received sa6 bits register register address: 06bh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rsa6f15 rsa6f13 rsa6f11 rsa6f 9 rsa6f7 rsa6f5 rsa6f3 rsa6f1 default 0 0 0 0 0 0 0 0 bit 7: sa6 bit of frame 15 (rsa6f15) bit 6: sa6 bit of frame 13 (rsa6f13) bit 5: sa6 bit of frame 11 (rsa6f11) bit 4: sa6 bit of frame 9 (rsa6f9) bit 3: sa6 bit of frame 7 (rsa6f7) bit 2: sa6 bit of frame 5 (rsa6f5) bit 1: sa6 bit of frame 3 (rsa6f3) bit 0: sa6 bit of frame 1 (rsa6f1) register name: e1rsa7 (e1 mode only) register description: received sa7 bits register register address: 06ch + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rsa7f15 rsa7f13 rsa7f11 rsa7f 9 rsa7f7 rsa7f5 rsa7f3 rsa7f1 default 0 0 0 0 0 0 0 0 bit 7: sa7 bit of frame 15 (rsa4f15) bit 6: sa7 bit of frame 13 (rsa7f13) bit 5: sa7 bit of frame 11 (rsa7f11) bit 4: sa7 bit of frame 9 (rsa7f9) bit 3: sa7 bit of frame 7 (rsa7f7) bit 2: sa7 bit of frame 5 (rsa7f5) bit 1: sa7 bit of frame 3 (rsa7f3) bit 0: sa7 bit of frame 1 (rsa7f1)
DS26518 8-port t1/e1/j1 transceiver 152 of 286 register name: e1rsa8 (e1 mode only) register description: received sa8 bits register register address: 06dh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rsa8f15 rsa8f13 rsa8f11 rsa8f 9 rsa8f7 rsa8f5 rsa8f3 rsa8f1 default 0 0 0 0 0 0 0 0 bit 7: sa8 bit of frame 15 (rsa8f15) bit 6: sa8 bit of frame 13 (rsa8f13) bit 5: sa8 bit of frame 11 (rsa8f11) bit 4: sa8 bit of frame 9 (rsa8f9) bit 3: sa8 bit of frame 7 (rsa8f7) bit 2: sa8 bit of frame 5 (rsa8f5) bit 1: sa8 bit of frame 3 (rsa8f3) bit 0: sa8 bit of frame 1 (rsa8f1) register name: sabits register description: received sax bits register register address: 06eh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? sa4 sa5 sa6 sa7 sa8 default 0 0 0 0 0 0 0 0 this register indicates the last received sax bi t. this can be used in conjunction with the rls7 register to determine which sax bits have changed. the user can program which sa bit positions should be monitored via the e1rsaimr register, and when a change is detected through an interrupt in rls7 .0, the user can determine which bit has changed by reading this register and comparing it with previous known values. bit 4: last received sa4 bit (sa4) bit 3: last received sa5 bit (sa4) bit 2: last received sa6 bit (sa5) bit 1: last received sa7 bit (sa7) bit 0: last received sa8 bit (sa8)
DS26518 8-port t1/e1/j1 transceiver 153 of 286 register name: sa6code register description: received sa6 codeword register register address: 06fh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? sa6n sa6n sa6n sa6n default 0 0 0 0 0 0 0 0 this register will report the received sa6 codeword per ets 300 233. the bits are monitored on a submultiframe asynchronous basis, so the pattern reported could be one of multiple patterns that would represent a valid codeword. the table below indicates which patterns reported in this register correspond to a given valid sa6 codeword. bits 3 to 0: sa6 codeword bit (sa6n) valid sa6 code possible reported patterns sa6_8 1000, 0100, 0010, 0001 sa6_a 1010, 0101 sa6_c 110, 0110, 0011, 1001 sa6_e 1110, 0111, 1011, 1101 sa6_f 1111 register name: rmmr register description: receive master mode register register address: 080h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name frm_en init_done ? ? ? ? sftrst t1/e1 default 0 0 0 0 0 0 0 0 bit 7: framer enable (frm_en). this bit must be set to the desired state before writing init_done. 0 = framer disabled?held in low-power state. 1 = framer enabled?all features active. bit 6: initialization done (init_done). the user must set this bit once he has written the configur ation registers. the host is required to write or clea r all device registers prior to setting this bit. once init_done is set, the DS26518 will check the frm_en bit and, if enabled, will begin operation based on the initial configuration. bit 1: soft reset (sftrst). level sensitive ?soft? reset. should be taken high, then low to reset the receiver. 0 = normal operation. 1 = reset the receiver. note: this reset does not clear the registers. bit 0: receiver t1/e1 mode select (t1/e1). sets operating mode for receiver only! this bit must be set to the desired state before writing init_done. 0 = t1 operation. 1 = e1 operation.
DS26518 8-port t1/e1/j1 transceiver 154 of 286 register name: rcr1 (t1 mode) register description: receive control register 1 register address: 081h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name synct rb8zs rfm arc syncc rjc synce resync default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for e1 mode. see rcr1 . bit 7: sync time (synct) 0 = qualify 10 bits. 1 = qualify 24 bits. bit 6: receive b8zs enable (rb8zs) 0 = b8zs disabled. 1 = b8zs enabled. bit 5: receive frame mode select (rfm) 0 = esf framing mode. 1 = d4 framing mode. bit 4: auto resync criteria (arc) 0 = resync on oof or los event. 1 = resync on oof only. bit 3: sync criteria (syncc) in d4 framing mode: 0 = search for ft pattern, then search for fs pattern. 1 = cross couple ft and fs pattern. in esf framing mode: 0 = search for fps pattern only. 1 = search for fps and verify with crc-6. bit 2: receive japanese crc-6 enable (rjc) 0 = use ansi:at&t:itu-t crc-6 calculation (normal operation). 1 = use japanese standard jt?g704 crc-6 calculation. bit 1: sync enable (synce) 0 = auto resync enabled. 1 = auto resync disabled. bit 0: resynchronize (resync). when toggled from low to high, a resynchr onization of the receive-side framer is initiated. must be cleared and se t again for a subsequent resync.
DS26518 8-port t1/e1/j1 transceiver 155 of 286 register name: rcr1 (e1 mode) register description: receive control register 1 register address: 081h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? rhdb3 rsigm rg802 rcrc4 frc synce resync default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for t1 mode. see rcr1 . bit 6: receive hdb3 enable (rhdb3) 0 = hdb3 disabled. 1 = hdb3 enabled (decoded per o.162). bit 5: receive signaling mode select (rsigm) 0 = cas signaling mode. 1 = ccs signaling mode. bit 4: receive g.802 enable (rg802). see figure 11-30 for details. 0 = do not force rchblkn high during bit 1 of time slot 26. 1 = force rchblkn high during bit 1 of time slot 26. bit 3: receive crc-4 enable (rcrc4) 0 = crc-4 disabled. 1 = crc-4 enabled. bit 2: frame resync criteria (frc) 0 = resync if fas received in error three consecutive times. 1 = resync if fas or bit 2 of non-fas is received in error three consecutive times. bit 1: sync enable (synce) 0 = auto resync enabled. 1 = auto resync disabled. bit 0: resynchronize (resync). when toggled from low to high, a resynchr onization of the receive-side framer is initiated. must be cleared and se t again for a subsequent resync.
DS26518 8-port t1/e1/j1 transceiver 156 of 286 register name: t1ribcc (t1 mode) register description: receive in-band code control register register address: 082h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? rup2 rup1 rup0 rdn2 rdn1 rdn0 default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for e1 mode. see e1rcr2 . bits 5 to 3: receive up code length definition bits (rup[2:0]) rup2 rup1 rup0 length selected 0 0 0 1 bits 0 0 1 2 bits 0 1 0 3 bits 0 1 1 4 bits 1 0 0 5 bits 1 0 1 6 bits 1 1 0 7 bits 1 1 1 8 : 16 bits bits 2 to 0: receive down code length definition bits (rdn[2:0]) rdn2 rdn1 rdn0 length selected 0 0 0 1 bits 0 0 1 2 bits 0 1 0 3 bits 0 1 1 4 bits 1 0 0 5 bits 1 0 1 6 bits 1 1 0 7 bits 1 1 1 8 : 16 bits register name: e1rcr2 (e1 mode) register description: receive control register 2 register address: 082h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? ? rlosa default 0 0 0 0 0 0 0 0 note: this register has an alternate definition for t1 mode. see t1ribcc . bit 0: receive loss of signal alternate criteria (rlosa). defines the criteria for a loss of signal condition. 0 = los declared upon 255 consecutive zeros (125 s). 1 = los declared upon 2048 consecutive zeros (1ms).
DS26518 8-port t1/e1/j1 transceiver 157 of 286 register name: rcr3 register description: receive control register 3 register address: 083h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ualaw rserc binv1 binv0 ? plb flb default 0 0 0 0 0 0 0 0 bit 6: u-law or a-law digital milliwatt code select (ualaw) 0 = u-law code is inserted based on t1rdmwe1 ?3 or e1rdmwe1 ?4 registers. 1 = a-law code is inserted based on t1rdmwe1 ?3 or e1rdmwe1 ?4 registers. bit 5: rsern control (rserc) 0 = allow rsern to output data as received under all conditions (normal operation). 1 = force rsern to one under loss of frame alignment conditions. bits 4 and 3: receive bit inversion (binv[1:0]) 00 = no inversion. 01 = invert framing. 10 = invert signaling. 11 = invert payload. bit 1: payload loopback (plb) 0 = loopback disabled. 1 = loopback enabled. when plb is enabled, the following will occur: 1) data will be transmitted on ttipn and tringn synchronous with rclkn instead of tclkn. 2) all of the receive-side signal s will continue to operate normally. 3) the tchclkn and tchblkn signals are forced low. 4) data at the tsern, tdatan, and tsign pins is ignored. in a plb situation, the DS26518 will loop the 192 bits (248 for e1) of payload data (with bpvs corrected) from the receive section back to the transmit section. the transmitter will fo llow the frame alignm ent provided by the receiver. the receive frame boundary is automatically fed into the transmit se ction, such that the transmit frame position is locked to the receiver (i.e., tsyncn is sourced from rsyncn). the fps framing pattern, crc-6 calculation, and the fdl bits (fas word, si, sa, e bits, and crc-4 for e1) are not looped back, they are reinserted by the DS26518 (i.e., the transmit se ction will modify the payload as if it was input at tsern). bit 0: framer loopback (flb) 0 = loopback disabled 1 = loopback enabled this loopback is useful in testing and debugging applicatio ns. in flb, the DS26518 will loop data from the transmit side back to the receive side. when flb is enabled, the following will occur: 1) (t1 mode) an unframed all-ones code will be transmitted at ttipn and tringn. (e1 mode) normal data will be transmitted at ttipn and tringn. 2) data at rtipn and rringn will be ignored. 3) all receive-side signals will take on timing synchronous with tc lkn instead of rclkn. note that it is not acceptable to have rclkn tied to tclkn during this loopback because this will cause an unstable condition.
DS26518 8-port t1/e1/j1 transceiver 158 of 286 register name: e1rdmwe1, e1rdmwe2, e1rdmwe3, e1rdmwe4 register description: e1 receive digital milliwatt enable registers 1 to 4 register address: 000h, 001h, 002h, 003h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 e1rdmwe1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 e1rdmwe2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 e1rdmwe3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 e1rdmwe4 bits 7 to 0: e1 receive digital milliwatt enable for channels 1 to 32 (ch[1:32]) 0 = do not affect the receive data associated with this channel. 1 = replace the receive data associated with this channel with digital milliwatt code. register name: tdmwe1, tdmwe2, tdmwe3, td mwe4 (t1 and e1 modes) register description: transmit digital milliwatt enable registers 1 to 4 register address: 100h, 101h, 102h, 103h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tdmwe1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tdmwe2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tdmwe3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 tdmwe4 bits 7 to 0: transmit digital milliwatt enable for channels 1 to 32 (ch[1:32]) 0 = do not affect the transmit data associated with this channel. 1 = replace the transmit data associated with this channel with digital milliwatt code.
DS26518 8-port t1/e1/j1 transceiver 159 of 286 register name: riocr register description: receive i/o configuration register register address: 084h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rclkinv rsyncinv h100en rsclkm rsms rsio rsms2 rsms1 rclkinv rsyncinv h100en rsclkm ? rsio rsms2 rsms1 default 0 0 0 0 0 1 0 0 bit 7: rclkn invert (rclkinv) 0 = no inversion. 1 = invert rclkn. bit 6: rsyncn invert (rsyncinv) 0 = no inversion. 1 = invert rsyncn as either input or output. bit 5: h.100 sync mode (h100en). see section 9.8.3 for more information. 0 = normal operation. 1 = rsyncn and tssyncion signals are shifted. bit 4: rsysclkn mode select (rsclkm) 0 = if rsysclkn is 1.544mhz. 1 = if rsysclkn is 2.048mhz or ibo enabled. bit 3: rsyncn multiframe skip control (rsms) (t1 mode only). useful in framing format conversions from d4 to esf. this function is not available when the receive-si de elastic store is enabled. rsyncn must be set to output multiframe pulses. 0 = rsyncn will output a pulse at every multiframe. 1 = rsyncn will output a pulse at every other multiframe. bit 2: rsyncn i/o select (rsio). ( note: this bit must be set to zero when elastic store is disabled.) the default value for this bit is a logic 1 so that the default state of rsyncn is as an input. 0 = rsyncn is an output. 1 = rsyncn is an input (only valid if elastic store enabled). bit 1: rsyncn mode select 2 (rsms2) t1: rsyncn pin must be programmed in the output frame mode. 0 = do not pulse double wide in signaling frames. 1 = do pulse double wide in signaling frames. e1: rsyncn pin must be programmed in the output multiframe mode. 0 = rsyncn outputs cas multiframe boundaries. 1 = rsyncn outputs crc-4 multiframe boundaries. in e1 mode, rsms2 also selects which multiframe signal is available at the rmsy ncn pin, regardless of the configuration for rsyncn. when rsms2 = 0, rmsyncn outputs cas multiframe boundaries; when rsms2 = 1, rmsyncn outputs crc-4 multiframe boundaries. bit 0: rsync mode select 1 (rsms1). selects frame or multiframe pulse when rsyncn pin is in output mode. in input mode (elastic store must be enabled) multiframe mode is only useful when receive signaling reinsertion is enabled. 0 = frame mode. 1 = multiframe mode.
DS26518 8-port t1/e1/j1 transceiver 160 of 286 register name: rescr register description: receive elastic store control register register address: 085h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rdatfmt rgclken ? rszs resalgn resr resmdm rese default 0 0 0 0 0 0 0 0 bit 7: receive channel data format (rdatfmt) 0 = 64kbps (data contained in all 8 bits). 1 = 56kbps (data contained in 7 out of the 8 bits). bit 6: receive gapped clock enable (rgclken) 0 = rchclkn functions normally. 1 = enable gapped bit clock output on rchclkn. note: rgpcken and rdatfmt are not associated with the elastic store and will be explained in the fractional support section. bit 4: receive slip zone select (rszs). this bit determines the minimum distance allowed between the elastic store read and write pointers before forcing a controlled slip . this bit is only applies during t1 to e1 or e1 to t1 conversion applications. 0 = force a slip at 9 bytes or less of separation (used for clustered blank channels). 1 = force a slip at 2 bytes or less of separation (u sed for distributed blank channels and minimum delay mode). bit 3: receive elastic store align (resalgn). setting this bit from a zero to a one will force the receive elastic store?s write/read pointers to a minimum separation of half a frame. no action will be taken if the pointer separation is already greater or equal to half a frame. if pointer separation is less than half a frame, the command will be executed and the data will be disrupted. should be toggled after rsysclkn ha s been applied and is stable. must be cleared and set again for a subsequent align. bit 2: receive elastic store reset (resr). setting this bit from a zero to a one will force the read pointer into the same frame that the write pointer is ex iting, minimizing the delay through t he elastic store. if this command should place the pointers within the slip zone (see bit 4), then an immediate slip will occur and the pointers will move back to opposite frames. should be toggled after rsysclkn has been applied and is stable. do not leave this bit set high. bit 1: receive elastic store minimum delay mode (resmdm) 0 = elastic stores operate at full two-frame depth. 1 = elastic stores operate at 32-bit depth. bit 0: receive elastic store enable (rese) 0 = elastic store is bypassed. 1 = elastic store is enabled.
DS26518 8-port t1/e1/j1 transceiver 161 of 286 register name: ercnt register description: error counter configuration register register address: 086h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name 1secs mcus mecu ecus eams fsbe moscrf lcvcrf 1secs mcus mecu ecus eams ? ? lcvcrf default 0 0 0 0 0 0 0 0 bit 7: one-second select (1secs). this bit allows for synchronization of the error counter updates between multiple ports. when ercnt.3 = 0, setting this bit (on a sp ecific framer) will update the framer?s error counters on the transition of the one-second timer from framer 1. no te that this bit should always be clear for framer 1. 0 = use the one-second timer that is internal to the framer. 1 = use the one-second timer from framer 1 to latch updates. bit 6 : manual counter update select (mcus). when manual update mode is enabled with eams, this bit can be used to allow the incoming latch_cnt signal to latch all counters. useful for synchronously latching counters of multiple DS26518 cores located on the same die. 0 = mecu is used to manually latch counters. 1 = counters are latched on the rising edge of the latch_cnt signal. bit 5: manual error counter update (mecu). when enabled by ercnt .3, the changing of this bit from a 0 to a 1 allows the next clock cycle to load the error counter re gisters with the latest counts and reset the counters. the user must wait a minimum of 250 s before reading the error count regi sters to allow for proper update. bit 4: error counter update select (ecus) t1 mode: 0 = update error counters once a second. 1 = update error counters every 42ms (333 frames). e1 mode: 0 = update error counters once a second. 1 = update error counters every 62.5ms (500 frames). bit 3: error accumulation mode select (eams) 0 = automatic updating of error counters enabled. the state of ercnt .4 determines accumulation time (timed update). 1 = user toggling of ercnt.5 determines accumulation time (manual update). bit 2: pcvcr fs-bit error report enable (fsbe) (t1 mode only) 0 = do not report bit errors in fs-bit position; only ft-bit position. 1 = report bit errors in fs-bit position as well as ft-bit position. bit 1: multiframe out of sync count register function select (moscrf) (t1 mode only) 0 = count errors in the framing bit position. 1 = count the number of multiframes out of sync. bit 0: t1 line code violation count register function select (lcvcrf) 0 = do not count excessive zeros. 1 = count excessive zeros.
DS26518 8-port t1/e1/j1 transceiver 162 of 286 register name: rhfc register description: receive hdlc fifo control register register address: 087h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? rfhwm1 rfhwm0 default 0 0 0 0 0 0 0 0 bits 1 and 0 : receive fifo high watermark select (rfhwm[1:0] rfhwm1 rfhwm0 receive fifo watermark 0 0 4 bytes 0 1 16 bytes 1 0 32 bytes 1 1 48 bytes register name: riboc register description: receive interleave bus operation control register register address: 088h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ibosel iboen ? ? ? default 0 0 0 0 0 0 0 0 bit 4: interleave bus operation select (ibosel). this bit selects channel or frame interleave mode. 0 = channel interleave 1 = frame interleave bit 3: interleave bus operation enable (iboen) 0 = interleave bus operation disabled. 1 = interleave bus operation enabled.
DS26518 8-port t1/e1/j1 transceiver 163 of 286 register name: t1rscc (t1 mode only) register description: in-band receive spare control register register address: 089h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? rsc2 rsc1 rsc0 default 0 0 0 0 0 0 0 0 bits 2 to 0: receive spare code length definition bits (rsc[2:0]) rsc2 rsc1 rsc0 length selected 0 0 0 1 bits 0 0 1 2 bits 0 1 0 3 bits 0 1 1 4 bits 1 0 0 5 bits 1 0 1 6 bits 1 1 0 7 bits 1 1 1 8 : 16 bits register name: rxpc register description: receive expansion port control register register address: 08ah + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? rbpdir rbpfus rbpen ? ? ? ? ? rbpdir ? rbpen default 0 0 0 0 0 0 0 0 bit 2: receive bert port direction control (rbpdir) 0 = normal (line) operation. rx bert port receives data from the receive framer. 1 = system (backplane) operation. rx bert port rece ives data from the transmit path. the transmit path enters the receive bert on the line side of the elastic store (if enabled). bit 1: receive bert port framed/unfra med select (rbpfus) (t1 mode only) 0 = the DS26518?s receive bert will not clock data from the f-bit position (framed). 1 = the DS26518?s receive bert will clock dat a from the f-bit position (unframed). bit 0: receive bert port enable (rbpen) 0 = receive bert port is not active. 1 = receive bert port is active.
DS26518 8-port t1/e1/j1 transceiver 164 of 286 register name: rbpbs register description: receive bert port bit suppress register register address: 08bh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name bpbse8 bpbse7 bpbse6 bpbse5 bpbse4 bpbse3 bpbse2 bpbse1 default 0 0 0 0 0 0 0 0 bit 7: receive channel bit 8 suppress (bpbse8). msb of the channel. set to one to stop this bit from being used. bit 6: receive channel bit 7 suppress (bpbse7). set to one to stop this bit from being used. bit 5: receive channel bit 6 suppress (bpbse6). set to one to stop this bit from being used. bit 4: receive channel bit 5 suppress (bpbse5). set to one to stop this bit from being used. bit 3: receive channel bit 4 suppress (bpbse4). set to one to stop this bit from being used. bit 2: receive channel bit 3 suppress (bpbse3). set to one to stop this bit from being used. bit 1: receive channel bit 2 suppress (bpbse2). set to one to stop this bit from being used. bit 0: receive channel bit 1 suppress (bpbse1). lsb of the channel. set to one to stop this bit from being used.
DS26518 8-port t1/e1/j1 transceiver 165 of 286 register name: rls1 register description: receive latched status register 1 register address: 090h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rraic raisc rlosc rlof c rraid raisd rlosd rlofd default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can create interrupts. bit 7: receive remote alarm indication condition clear (rraic). falling edge detect of rrai. set when a rrai condition has cleared. bit 6: receive alarm indicati on signal condition clear (raisc). falling edge detect of rais. set when a rais condition has cleared. bit 5: receive loss of signal condition clear (rlosc). falling edge detect of rlos. set when an rlos condition has cleared. bit 4: receive loss of frame condition clear (rlofc). falling edge detect of rlof. set when an rlof condition has cleared. bit 3: receive remote alarm indication condition detect (rraid). rising edge detect of rrai. set when a remote alarm is received at rringn and rtipn. bit 2: receive alarm indication signal condition detect (raisd). rising edge detect of rais.set when an unframed all-ones code is received at rringn and rtipn. bit 1: receive loss of signal condition detect (rlosd). rising edge detect of rlos. set when 192 consecutive zeros have been detec ted at rringn and rtipn. bit 0: receive loss of frame condition detect (rlofd). rising edge detect of rlof. set when the DS26518 has lost synchronized to the received data stream.
DS26518 8-port t1/e1/j1 transceiver 166 of 286 register name: rls2 (t1 mode) register description: receive latched status register 2 register address: 091h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ?- ? cofa 8zd 16zd sefe b8zs fbe default 0 0 0 0 0 0 0 0 note: all bits in these register are latched. th is register does not create interrupts. see rls2 for e1 mode. bit 5: change of frame alignment event (cofa). set when the last resync resulted in a change of frame or multiframe alignment. bit 4: eight zero detect event (8zd). set when a string of at least eight consecutive zeros (regardless of the length of the string) have been re ceived at rringn and rtipn. bit 3: sixteen zero detect event (16zd). set when a string of at least sixt een consecutive ze ros (regardless of the length of the string) have been received at rringn and rtipn. bit 2: severely errored framing event (sefe). set when 2 out of 6 framing bits (ft or fps) are received in error. bit 1: b8zs codeword detect event (b8zs). set when a b8zs codeword is detected at rringn and rtipn independent of whether the b8zs mode is selected or not. useful for automatically setting the line coding. bit 0: frame bit error event (fbe). set when a ft (d4) or fps (esf) fr aming bit is received in error. register name: rls2 (e1 mode) register description: e1 receive latched status register 2 register address: 091h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? crcrc casrc fasrc rsa1 rsa0 rcmf raf default 0 0 0 0 0 0 0 0 note: all bits in this register are latched. bits 0 to 3 can ca use interrupts. there is no asso ciated real-time register. see rls2 for t1 mode. bit 6: crc resync criteria met event (crcrc). set when 915:1000 codewords are received in error. bit 5: cas resync criteria met event (casrc). set when 2 consecutive cas mf alignment words are received in error. bit 4: fas resync criteria met event (fasrc). set when 3 consecutive fas words are received in error. bit 3: receive signaling all ones event (rsa1). set when the contents of time slot 16 contains fewer than three zeros over 16 consecutive frames. this alarm is not disabled in the ccs signaling mode. bit 2: receive signaling all zeros event (rsa0). set when over a full mf, time slot 16 contains all zeros. bit 1: receive crc-4 multiframe event (rcmf). set on crc-4 multiframe boundaries; will continue to be set every 2ms on an arbitrary boundar y if crc-4 is disabled. bit 0: receive align frame event (raf). set approximately every 250 s to alert the host that si and sa bits are available in the raf and rnaf registers.
DS26518 8-port t1/e1/j1 transceiver 167 of 286 register name: rls3 (t1 mode) register description: receive latched status register 3 register address: 092h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name lorcc lspc ldnc lupc lorcd lspd ldnd lupd default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can create interrupts. see rls3 for e1 mode. bit 7: loss of receive clock condition clear (lorcc). falling edge detect of lorc. set when an lorc condition was detected and then removed. bit 6: spare code detected condition clear (lspc). falling edge detect of lsp. set when a spare-code match condition was detected and then removed. bit 5: loop down code detected condition clear (ldnc). falling edge detect of ldn. set when a loop-down condition was detected and then removed bit 4: loop up code detected condition clear (lupc). falling edge detect of lup. set when a loop-up condition was detected and then removed. bit 3: loss of receive clock condition detect (lorcd). rising edge detect of lorc. set when the rclkn pin has not transitioned for one channel time. bit 2: spare code detected condition detect (lspd). rising edge detect of lsp. set when the spare code as defined in the t1rscd1 : t1rscd2 registers is being received. bit 1: loop down code detected condition detect (ldnd). rising edge detect of ldn. set when the loop down code as defined in the t1rdncd1 : t1rdncd2 register is being received. bit 0: loop up code detected condition detect (lupd). rising edge detect of lup. set when the loop up code as defined in the t1rupcd1 : t1rupcd2 register is being received.
DS26518 8-port t1/e1/j1 transceiver 168 of 286 register name: rls3 (e1 mode) register description: receive latched status register 3 register address: 092h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name lorcc ? v52lnkc rdmac lorcd ? v52lnkd rdmad default 0 0 0 0 0 0 0 0 note: all bits in this register are la tched and can create interrupts. see rls3 for t1 mode. bit 7: loss of receive clock clear (lorcc). change of state indication. set when an lorc condition has cleared (falling edge detect of lorc). bit 5: v5.2 link detected clear (v52lnkc). change of state indication. set when a v52lnk condition has cleared (falling edge detect of v52lnk). bit 4: receive distant mf alarm clear (rdmac). change of state indication. set when an rdma condition has cleared (falling edge detect of rdma). bit 3: loss of receive clock detect (lorcd). change of state indication. set when the rclkn pin has not transitioned for one channel time (rising edge detect of lorc). bit 1: v5.2 link detect (v52lnkd). change of state indication. set on detection of a v5.2 link identification signal. (g.965). this is the rising edge detect of v52lnk. bit 0: receive distant mf alarm detect (rdmad). change of state indication. set when bit-6 of time slot 16 in frame 0 has been set for two consecutive multiframes. this alarm is not disabled in the ccs signaling mode. this is the rising edge detect of rdma.
DS26518 8-port t1/e1/j1 transceiver 169 of 286 register name: rls4 register description: receive latched status register 4 register address: 093h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name resf resem rslip ? rscos 1sec timer rmf default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can create interrupts. bit 7: receive elastic store full event (resf). set when the receive elastic store buffer fills and a frame is deleted. bit 6: receive elastic store empty event (resem). set when the receive elastic store buffer empties and a frame is repeated. bit 5: receive elastic store slip occurrence event (rslip). set when the receive elastic store has either repeated or deleted a frame. bit 3: receive signaling change of state event (rscos). set when any channel selected by the receive signaling change of state interrupt enable registers ( rscse1 through rscse3) changes signaling state. bit 2: one-second timer (1sec). set on every one-second interval based on rclkn. bit 1: timer event (timer). this status bit indicates that the performance monitor counters have been updated and are available to be read by the hos t. the error counter update interval as determined by the settings in the error counter configuration register ( ercnt ). t1: set on increments of 1 second or 42ms based on rclkn, or a manual latch event. e1: set on increments of 1 second or 62.5ms based on rclkn, or a manual latch event. bit 0: receive multiframe event (rmf) t1 mode: set every 1.5ms on d4 mf boundaries or every 3ms on esf mf boundaries. e1 mode: set every 2.0ms on receive cas multiframe boun daries to alert host the signaling data is available. continues to set on an arbitrary 2.0m s boundary when cas signaling is not enabled.
DS26518 8-port t1/e1/j1 transceiver 170 of 286 register name: rls5 register description: receive latched status register 5 (hdlc) register address: 094h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? rovr rhobt rpe rps rhwms rnes default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can cause interrupts . bit 5: receive fifo overrun (rovr). set when the receive hdlc controller has terminated packet reception because the fifo buffer is full. bit 4: receive hdlc opening byte event (rhobt). set when the next byte available in the receive fifo is the first byte of a message. bit 3: receive packet end event (rpe). set when the hdlc controller detects either the finish of a valid message (i.e., crc check complete) or when the controller has experienced a message fault such as a crc checking error, or an overrun condition, or an abort has been seen. this is a latched bit and will be cleared when read. bit 2: receive packet start event (rps). set when the hdlc controller detects an opening byte. this is a latched bit and will be cleared when read. bit 1: receive fifo above high watermark set event (rhwms). set when the receive 64-byte fifo crosses the high watermark as defined by the re ceive hdlc fifo control register ( rhfc ). rising edge detect of rhwm. bit 0: receive fifo not empty set event (rnes). set when the receive fifo has transitioned from ?empty? to ?not empty? (at least one byte has been put into the fifo). rising edge detect of rne.
DS26518 8-port t1/e1/j1 transceiver 171 of 286 register name: rls7 (t1 mode) register description: receive latched status register 7 register address: 096h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? rrai-ci rais-ci rslc96 rfdlf bc bd default 0 0 0 0 0 0 0 0 note: all bits in this register are la tched and can create interrupts. see rls7 for e1 mode. bit 5: receive rai-ci detect (rrai-ci). set when an rai-ci pattern has been det ected by the receiver. this bit is active in esf framing mode only, and will set only if an rai condition is being detected ( rrts1 .3). when the host reads (and clears) this bit, it will set again each time the rai-ci pattern is detec ted (approximately every 1.1 seconds). bit 4: receive ais-ci detect (rais-ci). set when an ais-ci pattern has been detected by the receiver. this bit will set only if an ais condition is being detected ( rrts1 .2). this is a latched bit that must be cleared by the host, and will set again each time the ais-ci pattern is detected (approximately every 1.2 seconds). bit 3: receive slc-96 alignment event (rslc96). set when a valid slc-96 alignment pattern is detected in the fs bit stream, and the t1rslc1 ?3 registers have data available for retrieval. see section 9.9.4.4 for more information. bit 2: receive fdl register full event (rfdlf). set when the 8-bit t1rfdl register is full. useful for slc-96 operation, or manual extraction of fdl data bits. see section 9.9.5.4 for more information. bit 1: boc clear event (bc). set when a valid boc is no longer detected (with the disintegration filter applied). bit 0: boc detect event (bd). set when a valid boc has been detected (with the boc filter applied). register name: rls7 (e1 mode) register description: receive latched status register 7 register address: 096h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? sa6cd saxcd default 0 0 0 0 0 0 0 0 note: all bits in this register are la tched and can create interrupts. see rls7 for t1 mode. bit 1: sa6 codeword detect (sa6cd). set when a valid codeword (per ets 300 233) is detected in the sa6 bit positions. bit 0: sax bit change detect (saxcd). set when a bit change is detected in the sax bit position. the enabled sax bits are selected by the e1rsaimr register.
DS26518 8-port t1/e1/j1 transceiver 172 of 286 register name: rss1, rss2, rss3, rss4 register description: receive-signaling status registers 1 to 4 register address: 098h, 099h, 09ah, 09bh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1* rss1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rss2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17* rss3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 rss4 (e1 mode only) note: status bits in this register are latched. when a channel?s signaling data changes state, the respecti ve bit in registers rss1?4 will be set and latched. the rscos bit ( rls4 .3) will be set if the channel was also enabled by setting the appropriate bit in rscse1 ?4. the intb signal will go low if enabl ed by the interrupt mask bit rim4 .3. the bit will remain set until read. * note that in e1 cas mode, the lsb of rss1 would typically represent the cas alignment bits, and the lsb of rss3 represents reserved bits and t he distant multiframe alarm.
DS26518 8-port t1/e1/j1 transceiver 173 of 286 register name: t1rscd1 (t1 mode only) register description: receive spare code definition register 1 register address: 09ch + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 note: writing this register resets t he detector?s integration period. bit 7: receive spare code definition bit 7 (c7). first bit of the repeating pattern. bit 6: receive spare code definition bit 6 (c6). a don?t care if a 1-bit length is selected. bit 5: receive spare code definition bit 5 (c5). a don?t care if a 1- or 2-bit length is selected. bit 4: receive spare code definition bit 4 (c4). a don?t care if a 1- to 3-bit length is selected. bit 3: receive spare code definition bit 3 (c3). a don?t care if a 1- to 4-bit length is selected. bit 2: receive spare code definition bit 2 (c2). a don?t care if a 1- to 5-bit length is selected. bit 1: receive spare code definition bit 1 (c1). a don?t care if a 1- to 6-bit length is selected. bit 0: receive spare code definition bit 0 (c0). a don?t care if a 1- to 7-bit length is selected. register name: t1rscd2 (t1 mode only) register description: receive spare code definition register 2 register address: 09dh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 bit 7: receive spare code definition bit 7 (c7). a don?t care if a 1- to 7-bit length is selected. bit 6: receive spare code definition bit 6 (c6). a don?t care if a 1- to 7-bit length is selected. bit 5: receive spare code definition bit 5 (c5). a don?t care if a 1- to 7-bit length is selected. bit 4: receive spare code definition bit 4 (c4). a don?t care if a 1- to 7-bit length is selected. bit 3: receive spare code definition bit 3 (c3). a don?t care if a 1- to 7-bit length is selected. bit 2: receive spare code definition bit 2 (c2). a don?t care if a 1- to 7-bit length is selected. bit 1: receive spare code definition bit 1 (c1). a don?t care if a 1- to 7-bit length is selected. bit 0: receive spare code definition bit 0 (c0). a don?t care if a 1- to 7-bit length is selected.
DS26518 8-port t1/e1/j1 transceiver 174 of 286 register name: riir register description: receive interrupt information register register address: 9fh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? rls7 rls6* rls5 rls4 rls3 rls2** rls1 default 0 0 0 0 0 0 0 0 * rls6 is reserved for future use. ** currently rls2 does not create an interrupt, therefore this bit is not used in t1 mode. the receive interrupt information register indicates wh ich of the DS26518 status registers are generating an interrupt. when an interrupt occurs, the hos t can read riir to quickly identify wh ich of the receive status registers is (are) causing the in terrupt(s). the receive interrupt information register bits will clear once the appropriate interrupt has been serviced and cleared, as long as no addi tional, unmasked interrupt condition is present in the associated status register. status bits that have been masked via the receive interrupt mask (rimx) registers will also be masked from the riir register. register name: rim1 register description: receive interrupt mask register 1 register address: 0a0h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rraic raisc rlosc rlof c rraid raisd rlosd rlofd default 0 0 0 0 0 0 0 0 bit 7: receive remote alarm indication condition clear (rraic) 0 = interrupt masked. 1 = interrupt enabled. bit 6: receive alarm indicati on signal condition clear (raisc) 0 = interrupt masked. 1 = interrupt enabled. bit 5: receive loss of signal condition clear (rlosc) 0 = interrupt masked. 1 = interrupt enabled. bit 4: receive loss of frame condition clear (rlofc) 0 = interrupt masked. 1 = interrupt enabled. bit 3 : receive remote alarm i ndication condition detect (rraid) 0 = interrupt masked. 1 = interrupt enabled. bit 2: receive alarm indication signal condition detect (raisd) 0 = interrupt masked. 1 = interrupt enabled. bit 1: receive loss of signal condition detect (rlosd) 0 = interrupt masked. 1 = interrupt enabled. bit 0: receive loss of frame condition detect (rlofd) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 175 of 286 register name: rim2 (e1 mode only) register description: e1 receive interrupt mask register 2 register address: 0a1h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? rsa1 rsa0 rcmf raf default 0 0 0 0 0 0 0 0 bit 3: receive-signaling all ones event (rsa1) 0 = interrupt masked. 1 = interrupt enabled. bit 2: receive-signaling all zeros event (rsa0) 0 = interrupt masked. 1 = interrupt enabled. bit 1: receive crc-4 multiframe event (rcmf) 0 = interrupt masked. 1 = interrupt enabled. bit 0: receive align frame event (raf) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 176 of 286 register name: rim3 (t1 mode) register description: receive interrupt mask register 3 register address: 0a2h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name lorcc lspc ldnc lupc lorcd lspd ldnd lupd default 0 0 0 0 0 0 0 0 note: see rim3 for e1 mode. bit 7: loss of receive clock condition clear (lorcc) 0 = interrupt masked. 1 = interrupt enabled. bit 6: spare code detected condition clear (lspc) 0 = interrupt masked. 1 = interrupt enabled. bit 5: loop down code detected condition clear (ldnc) 0 = interrupt masked. 1 = interrupt enabled. bit 4: loop up code detected condition clear (lupc) 0 = interrupt masked. 1 = interrupt enabled. bit 3: loss of receive clock condition detect (lorcd) 0 = interrupt masked 1 = interrupt enabled bit 2: spare code detected condition detect (lspd) 0 = interrupt masked. 1 = interrupt enabled. bit 1 : loop down code detected condition detect (ldnd) 0 = interrupt masked. 1 = interrupt enabled. bit 0: loop up code detected condition detect (lupd) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 177 of 286 register name: rim3 (e1 mode) register description: e1 receive interrupt mask register 3 register address: 0a2h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name lorcc ? v52lnkc rdmac lorcd ? v52lnkd rdmad default 0 0 0 0 0 0 0 0 note: see rim3 for t1 mode. bit 7: loss of receive clock clear (lorcc) 0 = interrupt masked. 1 = interrupt enabled. bit 5: v5.2 link detected clear (v52lnkc) 0 = interrupt masked. 1 = interrupt enabled. bit 4: receive distant mf alarm clear (rdmac) 0 = interrupt masked. 1 = interrupt enabled. bit 3: loss of receive clock detect (lorcd) 0 = interrupt masked. 1 = interrupt enabled. bit 1: v5.2 link detect (v52lnkd) 0 = interrupt masked. 1 = interrupt enabled. bit 0: receive distant mf alarm detect (rdmad) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 178 of 286 register name: rim4 register description: receive interrupt mask register 4 register address: 0a3h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name resf resem rslip ? rscos 1sec timer rmf default 0 0 0 0 0 0 0 0 bit 7: receive elastic store full event (resf) 0 = interrupt masked. 1 = interrupt enabled. bit 6: receive elastic store empty event (resem) 0 = interrupt masked. 1 = interrupt enabled. bit 5: receive elastic store slip occurrence event (rslip) 0 = interrupt masked. 1 = interrupt enabled. bit 3: receive signaling change of state event (rscos) 0 = interrupt masked. 1 = interrupt enabled. bit 2: one-second timer (1sec) 0 = interrupt masked. 1 = interrupt enabled. bit 1: timer event (timer) 0 = interrupt masked. 1 = interrupt enabled. bit 0: receive multiframe event (rmf) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 179 of 286 register name: rim5 register description: receive interrupt mask 5 (hdlc) register address: 0a4h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? rovr rhobt rpe rps rhwms rnes default 0 0 0 0 0 0 0 0 bit 5: receive fifo overrun (rovr) 0 = interrupt masked. 1 = interrupt enabled. bit 4: receive hdlc opening byte event (rhobt) 0 = interrupt masked. 1 = interrupt enabled. bit 3: receive packet end event (rpe) 0 = interrupt masked. 1 = interrupt enabled. bit 2: receive packet start event (rps) 0 = interrupt masked. 1 = interrupt enabled. bit 1: receive fifo above high watermark set event (rhwms) 0 = interrupt masked. 1 = interrupt enabled. bit 0: receive fifo not empty set event (rnes) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 180 of 286 register name: rim7 (t1 mode) register description: receive interrupt mask register 7 (boc:fdl) register address: 0a6h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? rrai-ci rais-ci rslc96 rfdlf bc bd default 0 0 0 0 0 0 0 0 note: see rim7 for e1 mode . bit 5: receive rai-ci (rrai-ci) 0 = interrupt masked. 1 = interrupt enabled. bit 4: receive ais-ci (rais-ci) 0 = interrupt masked. 1 = interrupt enabled. bit 3: receive slc-96 (rslc96) 0 = interrupt masked. 1 = interrupt enabled. bit 2: receive fdl register full (rfdlf) 0 = interrupt masked. 1 = interrupt enabled. bit 1: boc clear event (bc) 0 = interrupt masked. 1 = interrupt enabled. bit 0: boc detect event (bd) 0 = interrupt masked. 1 = interrupt enabled. register name: rim7 (e1 mode) register description: receive interrupt mask register 7 (boc:fdl) register address: 0a6h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? sa6cd saxcd default 0 0 0 0 0 0 0 0 note: see rim7 for t1 mode. bit 1: sa6 codeword detect (sa6cd). this bit will enable the interrupt generated when a valid codeword (per ets 300 233) is detected in the sa6 bits. 0 = interrupt masked. 1 = interrupt enabled. bit 0: sax change detect (saxcd). this bit will enable the interrupt generated when a change of state is detected in any of the unmasked sax bit positions. t he masked or unmasked sax bits are selected by the e1rsaimr register. 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 181 of 286 register name: rscse1, rscse2, rscse3, rscse4 register description: receive-signaling change of state enable registers 1 to 4 register address: 0a8h, 0a9h, 0aah, 0abh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 rscse1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rscse2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 rscse3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 rscse4 (e1 mode only) setting any of the ch[1:32] bits in the rsc se1 to rscse4 registers will cause rscos ( rls4 .3) to be set when that channel?s signaling data changes state.
DS26518 8-port t1/e1/j1 transceiver 182 of 286 register name: t1rupcd1 (t1 mode only) register description: receive up code definition register 1 register address: 0ach + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 note: writing this register resets t he detector?s integration period. bit 7: receive up code definition bit 7 (c7). first bit of the repeating pattern. bit 6: receive up code definition bit 6 (c6). a don?t care if a 1-bit length is selected. bit 5: receive up code definition bit 5 (c5). a don?t care if a 1- or 2-bit length is selected. bit 4: receive up code definition bit 4 (c4). a don?t care if a 1- to 3-bit length is selected. bit 3: receive up code definition bit 3 (c3). a don?t care if a 1- to 4-bit length is selected. bit 2: receive up code definition bit 2 (c2). a don?t care if a 1- to 5-bit length is selected. bit 1: receive up code definition bit 1 (c1). a don?t care if a 1- to 6-bit length is selected. bit 0: receive up code definition bit 0 (c0). a don?t care if a 1- to 7-bit length is selected. register name: t1rupcd2 (t1 mode only) register description: receive up code definition register 2 register address: 0adh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 bit 7: receive up code definition bit 7 (c7). a don?t care if a 1- to 7-bit length is selected. bit 6: receive up code definition bit 6 (c6). a don?t care if a 1- to 7-bit length is selected. bit 5: receive up code definition bit 5 (c5). a don?t care if a 1- to 7-bit length is selected. bit 4: receive up code definition bit 4 (c4). a don?t care if a 1- to 7-bit length is selected. bit 3: receive up code definition bit 3 (c3). a don?t care if a 1- to 7-bit length is selected. bit 2: receive up code definition bit 2 (c2). a don?t care if a 1- to 7-bit length is selected. bit 1: receive up code definition bit 1 (c1). a don?t care if a 1- to 7-bit length is selected. bit 0: receive up code definition bit 0 (c0). a don?t care if a 1- to 7-bit length is selected.
DS26518 8-port t1/e1/j1 transceiver 183 of 286 register name: t1rdncd1 (t1 mode only) register description: receive down code definition register 1 register address: 0aeh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 note: writing this register resets t he detector?s integration period. bit 7: receive down code definition bit 7 (c7). first bit of the repeating pattern. bit 6: receive down code definition bit 6 (c6). a don?t care if a 1-bit length is selected. bit 5: receive down code definition bit 5 (c5). a don?t care if a 1- or 2-bit length is selected. bit 4: receive down code definition bit 4 (c4). a don?t care if a 1- to 3-bit length is selected. bit 3: receive down code definition bit 3 (c3). a don?t care if a 1- to 4-bit length is selected. bit 2: receive down code definition bit 2 (c2). a don?t care if a 1- to 5-bit length is selected. bit 1: receive down code definition bit 1 (c1). a don?t care if a 1- to 6-bit length is selected. bit 0: receive down code definition bit 0 (c0). a don?t care if a 1- to 7-bit length is selected. register name: t1rdncd2 (t1 mode only) register description: receive down code definition register 2 register address: 0afh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 bit 7: receive down code definition bit 7 (c7). a don?t care if a 1- to 7-bit length is selected. bit 6: receive down code definition bit 6 (c6). a don?t care if a 1- to 7-bit length is selected. bit 5: receive down code definition bit 5 (c5). a don?t care if a 1- to 7-bit length is selected. bit 4: receive down code definition bit 4 (c4). a don?t care if a 1- to 7-bit length is selected. bit 3: receive down code definition bit 3 (c3). a don?t care if a 1- to 7-bit length is selected. bit 2: receive down code definition bit 2 (c2). a don?t care if a 1- to 7-bit length is selected. bit 1: receive down code definition bit 1 (c1). a don?t care if a 1- to 7-bit length is selected. bit 0: receive down code definition bit 0 (c0). a don?t care if a 1- to 7-bit length is selected.
DS26518 8-port t1/e1/j1 transceiver 184 of 286 register name: rrts1 register description: receive real-time status register 1 register address: 0b0h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? rrai rais rlos rlof default 0 0 0 0 0 0 0 0 note: all bits in this register are real-time (not latched). bit 3: receive remote alarm indication condition (rrai). set when a remote alarm is received at rringn and rtipn. bit 2: receive alarm indicat ion signal condition (rais). set when an unframed all-ones code is received at rringn and rtipn. bit 1: receive loss of signal condition (rlos). set when 192 consecutive zeros have been detected at rringn and rtipn. bit 0: receive loss of frame condition (rlof). set when the DS26518 is not synchronized to the received data stream.
DS26518 8-port t1/e1/j1 transceiver 185 of 286 register name: rrts3 (t1 mode) register description: receive real-time status register 3 register address: 0b2h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? lorc lsp ldn lup default 0 0 0 0 0 0 0 0 note: all bits in this register are real-time (not latched). see rrts3 for e1 mode. bit 3: loss of receive clock condition (lorc). set when the rclkn pin has not transitioned for one channel time. bit 2: spare code detected condition (lsp). set when the spare code as defined in the t1rscd1 : t1rscd2 registers is being received. bit 1: loop-down code detected condition (ldn). set when the loop-down code as defined in the t1rdncd1 : t1rdncd2 register is being received. bit 0: loop-up code detected condition (lup). set when the loop-up code as defined in the t1rupcd1 : t1rupcd2 register is being received. register name: rrts3 (e1 mode) register description: receive real-time status register 3 register address: 0b2h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? lorc ? v52lnk rdma default 0 0 0 0 0 0 0 0 note: all bits in this register are real-time (not latched). see rrts3 for t1 mode. bit 3: loss of receive clock condition (lorc). set when the rclkn pin has not transitioned for one channel time. bit 1: v5.2 link detected condition (v52lnk). set on detection of a v5.2 link identification signal (g.965). bit 0: receive distant mf alarm condition (rdma). set when bit-6 of time slot 16 in frame 0 has been set for two consecutive multiframes. this alarm is not disabled in the ccs signaling mode.
DS26518 8-port t1/e1/j1 transceiver 186 of 286 register name: rrts5 register description: receive real-time status register 5 (hdlc) register address: 0b4h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ps2 ps1 ps0 ? ? rhwm rne default 0 0 0 0 0 0 0 0 note: all bits in this register are real time. bits 6 to 4: receive packet status (ps[2:0]) . these are real-time bits indicating the status as of the last read of the receive fifo. ps2 ps1 ps0 packet status 0 0 0 in progress: end of message has not yet been reached. 0 0 1 packet ok: packet ended with correct crc codeword. 0 1 0 crc error: a closing flag was detected, preceded by a corrupt crc codeword. 0 1 1 abort: packet ended because an abort signal was detected (7 or more ones in a row). 1 0 0 overrun: hdlc controller terminated reception of packet because receive fifo is full. bit 1: receive fifo above high watermark condition (rhwm). set when the receive 64-byte fifo fills beyond the high watermark as defined by the re ceive hdlc fifo control register (rhfc). this is a real-time bit. bit 0: receive fifo not empty condition (rne). set when the receive 64-byte fifo has at least one byte available for a read. this is a real-time bit. register name: rhpba register description: receive hdlc packet bytes available register register address: 0b5h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ms rpba6 rpba5 rpba4 rpba3 rpba2 rpba1 rpba0 default 0 0 0 0 0 0 0 0 bit 7: message status (ms) 0 = bytes indicated by rpba0 th rough rpba6 are the end of a mess age. host must check the hdlc status register for details. 1 = bytes indicated by rpba0 th rough rpba6 are the beginning or c ontinuation of a message. the host does not need to check the hdlc status. the ms bit will return to a value of ?1? when the rx hdlc fifo is empty. bits 6 to 0: receive fifo packet bytes available count (rpba[6:0]). rpba0 is the lsb.
DS26518 8-port t1/e1/j1 transceiver 187 of 286 register name: rhf register description: receive hdlc fifo register register address: 0b6h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rhd7 rhd6 rhd5 rhd4 rhd3 rhd2 rhd1 rhd0 default 0 0 0 0 0 0 0 0 bit 7: receive hdlc data bit 7 (rhd7). msb of a hdlc packet data byte. bit 6: receive hdlc data bit 6 (rhd6) bit 5: receive hdlc data bit 5 (rhd5) bit 4: receive hdlc data bit 4 (rhd4) bit 3: receive hdlc data bit 3 (rhd3) bit 2: receive hdlc data bit 2 (rhd2) bit 1: receive hdlc data bit 1 (rhd1) bit 0: receive hdlc data bit 0 (rhd0). lsb of a hdlc packet data byte. register name: rbcs1, rbcs2, rbcs3, rbcs4 register description: receive blank channel select registers 1 to 4 register address: 0c0h, 0c1h, 0c2h, 0c3h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 rbcs1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rbcs2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 rbcs3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 rbcs4 (e1 mode only) bits 7 to 0: receive blank channel select for channels 1 to 32 (ch[1:32]) 0 = do not blank this channel (channel data is available on rsern). 1 = data on rsern is forced to all ones for this channel. note that when two or more sequential channels are chosen to be blanked, the receive-slip zone select bit should be set to zero. if the blank channels are distributed (such as 1, 5, 9, 13, 17, 21, 25, 29), then the rszs bit can be set to one, which may provide a lower occurrence of slips in certain applications.
DS26518 8-port t1/e1/j1 transceiver 188 of 286 register name: rcbr1, rcbr2, rcbr3, rcbr4 register description: receive channel blocking registers 1 to 4 register address: 0c4h, 0c5h, 0c6h, 0c7h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 rcbr1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rcbr2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 rcbr3 ch32 ch31 ch30 ch 29 ch28 ch27 ch26 ch25 (f-bit) rcbr4 (e1 mode only)* bits 7 to 0: channel blocking control bits for receive channels 1 to 32 (ch[1:32]) 0 = force the rchblkn pin to remain low during this channel time. 1 = force the rchblkn pin high during this channel time. *note that rcbr4 has two functions: when 2.048mhz backplane mode is selected, this regi ster allows the user to enable the channel blocking signal for any of the 32 possible backplane channels. when 1.544mhz backplane mode is selected, the lsb of this register determi nes whether or not the rchblkn signal will pulse high during the f-bit time. in this mode rcbr4.1 to rcbr4.7 should be set to 0. rcbr4.0 = 0, do not pulse rchblkn during the f-bit. rcbr4.0 = 1, pulse rchblkn during the f-bit. register name: rsi1, rsi2, rsi3, rsi4 register description: receive-signaling reinsertion enable registers 1 to 4 register address: 0c8h, 0c9h, 0cah, 0cbh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 rsi1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rsi2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 rsi3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 rsi4 (e1 mode only) setting any of the ch[1:24] bits in the rsi1 through rsi4 registers will cause signaling data to be reinserted for the associated channel. rsi4 is used for 2.048mhz backplane operation.
DS26518 8-port t1/e1/j1 transceiver 189 of 286 register name: rgccs1, rgccs2, rgccs3, rgccs4 register description: receive gapped clock channel select registers 1 to 4 register address: 0cch, 0cdh, 0ceh, 0cfh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 rgccs1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rgccs2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 rgccs3 ch32 ch31 ch30 ch 29 ch28 ch27 ch26 ch25 (f-bit) rgccs4 (e1 mode only)* bits 7 to 0: gapped clock channel select bits for receive channels 1 to 32(ch[1:32]) 0 = no clock is present on rchclkn during this channel time. 1 = force a clock on rchclkn during this channel time. the clock will be synchronous with rclkn if the elastic store is disabled, and synchronous with rsysclkn if the elastic store is enabled. * note that rgccs4 has two functions: when 2.048mhz backplane mode is selected, this regi ster allows the user to enable the gapped clock on rchclkn for any of the 32 possible backplane channels. when 1.544mhz backplane mode is selected, the lsb of this register determines w hether or not a clock is generated on rchclkn during the f-bit time: rgccs4.0 = 0, do not generat e a clock during the f-bit. rgccs4.0 = 1, generate a clock during the f-bit. in this mode rgccs4.1 to rgccs4.7 should be set to 0. register name: rcice1, rcice2, rcice3, rcice4 register description: receive channel idle code enable registers 1 to 4 register address: 0d0h, 0d1h, 0d2h, 0d3h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 rcice1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rcice2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 rcice3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 rcice4 (e1 mode only) bits 7 to 0: receive channels 1 to 32 code insertion control bits (ch[1:32]) 0 = do not insert data from the idle code array into the receive data stream. 1 = insert data from the idle code array into the receive data stream.
DS26518 8-port t1/e1/j1 transceiver 190 of 286 register name: rbpcs1, rbpcs2, rbpcs3, rbpcs4 register description: receive bert port channel select registers 1 to 4 register address: 0d4h, 0d5h, 0d6h, 0d7h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 rbpcs1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 rbpcs2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 rbpcs3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 rbpcs4 (e1 mode only) bits 7 to 0: bert port channel select receive channels 1 to 32 (ch[1:32]) 0 = do not enable the receive bert clock for the associated channel time, or map the selected channel data out of the receive bert port. 1 = enable receive bert clock for the associated channel time, and allow mapping of the selected channel data out of the receive bert port. multiple or all channels may be selected simultaneously.
DS26518 8-port t1/e1/j1 transceiver 191 of 286 10.4.2 transmit register descriptions register name: thc1 register description: transmit hdlc control register 1 register address: 110h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name nofs teoml thr thms tfs teom tzsd tcrcd default 0 0 0 0 0 0 0 0 bit 7: number of flags select (nofs) 0 = send one flag between consecutive messages. 1 = send two flags between consecutive messages. bit 6: transmit end of message and loop (teoml). to loop on a message, should be set to a one just before the last data byte of an hdlc packet is written into the transmit fifo. the message w ill repeat until t he user clears this bit or a new message is written to the transmit fifo. if the host clears the bit, the looping message will complete then flags will be transmitted until new message is written to the fifo. if the host terminates the loop by writing a new message to the fifo the loop will termin ate, one or two flags will be transmitted and the new message will start. if not disabled via tcrcd, the transmi tter will automatically append a two-byte crc code to the end of all messages. bit 5: transmit hdlc reset (thr). will reset the transmit hdlc controlle r and flush the transmit fifo. an abort followed by 7eh or ffh flags/idle will be transmitted until a new pa cket is initiated by writing new data into the fifo. this is an acknowledged reset, that is, the host ne ed only to set the bit and the DS26518 will clear it once the reset operation is complete. total time for the reset is less than 250 s. 0 = normal operation. 1 = reset transmit hdlc controller and flush the transmit fifo. bit 4: transmit hdlc mapping select (thms) 0 = transmit hdlc assigned to channels. 1 = transmit hdlc assigned to fdl (t1 mode), sa bits (e1 mode). this mode must be enabled with t1.tcr2 .7. bit 3: transmit flag /idle select (tfs). this bit selects the inter-message fill character after the closing and before the opening flags (7eh). 0 = 7eh 1 = ffh bit 2: transmit end of message (teom). should be set to a one just before the last data byte of an hdlc packet is written into the transmit fifo at thf. if not dis abled via tcrcd, the transmitter will automatically append a two byte crc code to the end of the message. bit 1: transmit zero stuffer defeat (tzsd). the zero stuffer function automatica lly inserts a zero in the message field (between the flags) after five consecutive ones to prevent the emulation of a fl ag or abort sequence by the data pattern. the receiver automatica lly removes (de-stuffs) any zero after five ones in the message field. 0 = enable the zero stuffer (normal operation). 1 = disable the zero stuffer. bit 0: transmit crc defeat (tcrcd). a two-byte crc code is autom atically appended to the outbound message. this bit can be used to disable the crc function. 0 = enable crc generation (normal operation). 1 = disable crc generation.
DS26518 8-port t1/e1/j1 transceiver 192 of 286 register name: thbse register description: transmit hdlc bit suppress register address: 111h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tbse8 tbse7 tbse6 tbse5 tbse4 tbse3 tbse2 tbse1 default 0 0 0 0 0 0 0 0 bit 7: transmit bit 8 suppress (tbse8). msb of the channel. set to one to stop this bit from being used. bit 6: transmit bit 7 suppress (tbse7). set to one to stop this bit from being used. bit 5: transmit bit 6 suppress (tbse6). set to one to stop this bit from being used. bit 4: transmit bit 5 suppress (tbse5). set to one to stop this bit from being used. bit 3: transmit bit 4 suppress (tbse4). set to one to stop this bit from being used. bit 2: transmit bit 3 suppress (tbse3). set to one to stop this bit from being used. bit 1: transmit bit 2 suppress (tbse2). set to one to stop this bit from being used. bit 0: transmit bit 1 suppress (tbse1). lsb of the channel. set to one to stop this bit from being used. register name: thc2 register description: transmit hdlc control register 2 register address: 113h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tabt sboc thcen thcs4 thcs3 thcs2 thcs1 thcs0 tabt ? thcen thcs4 thcs3 thcs2 thcs1 thcs0 default 0 0 0 0 0 0 0 0 bit 7: transmit abort (tabt). a 0-to-1 transition will cause the fifo contents to be dumped and one feh abort to be sent followed by 7eh or ffh flags/idle until a new packet is initiated by writing new data into the fifo. must be cleared and set again for a subsequent abort to be sent. bit 6: send boc (sboc) (t1 mode only). set = 1 to transmit the boc code placed in bits 0 to 5 of the t1tboc register. bit 5: transmit hdlc c ontroller enable (thcen) 0 = transmit hdlc controller is not enabled 1 = transmit hdlc controller is enabled bits 4 to 0: transmit hdlc channel select (thcs[4:0]). determines which dso channel will carry the hdlc message if enabled. changes to this value are acknowledged only upon a transmit hdlc controller reset (thr at thc1 .5).
DS26518 8-port t1/e1/j1 transceiver 193 of 286 register name: e1tsacr register description: e1 transmit sa-bit control register register address: 114h + (200h x (n - 1)) : where n = 1 to 8, for ports 1 to 8 bit # 7 6 5 4 3 2 1 0 name siaf sinaf ra sa4 sa5 sa6 sa7 sa8 default 0 0 0 0 0 0 0 0 bit 7: international bit in ali gn frame insertion control bit (siaf) 0 = do not insert data from the e1tsiaf register into the transmit data stream. 1 = insert data from the e1tsiaf register into the transmit data stream. bit 6: international bit in non-align frame insertion control bit (sinaf) 0 = do not insert data from the e1tsinaf register into the transmit data stream. 1 = insert data from the e1tsinaf register into the transmit data stream. bit 5: remote alarm insertion control bit (ra) 0 = do not insert data from the e1tra register into the transmit data stream. 1 = insert data from the e1tra register into the transmit data stream. bit 4: additional bit 4 insertion control bit (sa4) 0 = do not insert data from the e1tsa4 register into the transmit data stream. 1 = insert data from the e1tsa4 register into the transmit data stream. bit 3: additional bit 5 insertion control bit (sa5) 0 = do not insert data from the e1tsa5 register into the transmit data stream. 1 = insert data from the e1tsa5 register into the transmit data stream. bit 2: additional bit 6 insertion control bit (sa6) 0 = do not insert data from the e1tsa6 register into the transmit data stream. 1 = insert data from the e1tsa6 register into the transmit data stream. bit 1: additional bit 7 insertion control bit (sa7) 0 = do not insert data from the e1tsa7 register into the transmit data stream. 1 = insert data from the e1tsa7 register into the transmit data stream. bit 0: additional bit 8 insertion control bit (sa8) 0 = do not insert data from the e1tsa8 register into the transmit data stream. 1 = insert data from the e1tsa8 register into the transmit data stream.
DS26518 8-port t1/e1/j1 transceiver 194 of 286 register name: ssie1, ssie2, ssie3, ssie4 register description: software-signaling insertion enable registers 1 to 4 register address: 118h, 119h, 11ah, 11bh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 ssie1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 ssie2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 ssie3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 ssie4 (e1 mode only) bits 7 to 0: software-signaling insertion enable for channels 1 to 32 (ch[1:32]). these bits determine which channels are to have signaling inserted fo rm the transmit signaling registers. 0 = do not source signaling data from the ts registers for this channel. 1 = source signaling data from the ts registers for this channel. register name: tidr1 to tidr32 register description: transmit idle code definition registers 1 to 32 register address: 120h to 13fh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 bits 7 to 0: per-channel idle code bits (c[7:0]). c0 is the lsb of the code (this bi t is transmitted last). address 120h is for channel 1, address 13fh is for channel 32. tidr25:tidr32 are e1 mode.
DS26518 8-port t1/e1/j1 transceiver 195 of 286 register name: ts1 to ts16 register description: transmit-signaling registers register address: 140h to 14fh + (200h x (n - 1)) : where n = 1 to 8 t1 mode: (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch1-a ch1-b ch1-c ch1-d ch13-a ch13-b ch13-c ch13-d ts1 ch2-a ch2-b ch2-c ch2-d ch14-a ch14-b ch14-c ch14-d ts2 ch3-a ch3-b ch3-c ch3-d ch15-a ch15-b ch15-c ch15-d ts3 ch4-a ch4-b ch4-c ch4-d ch16-a ch16-b ch16-c ch16-d ts4 ch5-a ch5-b ch5-c ch5-d ch17-a ch17-b ch17-c ch17-d ts5 ch6-a ch6-b ch6-c ch6-d ch18-a ch18-b ch18-c ch18-d ts6 ch7-a ch7-b ch7-c ch7-d ch19-a ch19-b ch19-c ch19-d ts7 ch8-a ch8-b ch8-c ch8-d ch20-a ch20-b ch20-c ch20-d ts8 ch9-a ch9-b ch9-c ch9-d ch21-a ch21-b ch21-c ch21-d ts9 ch10-a ch10-b ch10- c ch10-d ch22-a ch22-b ch22-c ch22-d ts10 ch11-a ch11-b ch11- c ch11-d ch23-a ch23-b ch23-c ch23-d ts11 ch12-a ch12-b ch12- c ch12-d ch24-a ch24-b ch24-c ch24-d ts12 note: in d4 framing mode, the c and d bits are not used. e1 mode: (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name 0 0 0 0 x y x x ts1 ch1-a ch1-b ch1-c ch1-d ch16-a ch16-b ch16-c ch16-d ts2 ch2-a ch2-b ch2-c ch2-d ch17-a ch17-b ch17-c ch17-d ts3 ch3-a ch3-b ch3-c ch3-d ch18-a ch18-b ch18-c ch18-d ts4 ch4-a ch4-b ch4-c ch4-d ch19-a ch19-b ch19-c ch19-d ts5 ch5-a ch5-b ch5-c ch5-d ch20-a ch20-b ch20-c ch20-d ts6 ch6-a ch6-b ch6-c ch6-d ch21-a ch21-b ch21-c ch21-d ts7 ch7-a ch7-b ch7-c ch7-d ch22-a ch22-b ch22-c ch22-d ts8 ch8-a ch8-b ch8-c ch8-d ch23-a ch23-b ch23-c ch23-d ts9 ch9-a ch9-b ch9-c ch9-d ch24-a ch24-b ch24-c ch24-d ts10 ch10-a ch10-b ch10- c ch10-d ch25-a ch25-b ch25-c ch25-d ts11 ch11-a ch11-b ch11- c ch11-d ch26-a ch26-b ch26-c ch26-d ts12 ch12-a ch12-b ch12- c ch12-d ch27-a ch27-b ch27-c ch27-d ts13 ch13-a ch13-b ch13- c ch13-d ch28-a ch28-b ch28-c ch28-d ts14 ch14-a ch14-b ch14- c ch14-d ch29-a ch29-b ch29-c ch29-d ts15 ch15-a ch15-b ch15- c ch15-d ch30-a ch30-b ch30-c ch30-d ts16
DS26518 8-port t1/e1/j1 transceiver 196 of 286 register name: tcice1, tcice2, tcice3, tcice4 register description: transmit channel idle code enable registers 1 to 4 register address: 150h, 151h, 152h, 153h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tcice1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tcice2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tcice3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 tcice4 (e1 mode only) the transmit channel idle code enable registers (tci ce1?4) are used to determine which of the 24 t1 channels (or 32 e1 channels) from the backplane should be overwritten with the code placed in the transmit idle code definition register ( tidr1 ?32). bits 7 to 0: transmit channels 1 to 32 code insertion control bits (ch[1:32]) 0 = do not insert data from the idle code array into the transmit data stream. 1 = insert data from the idle code array into the transmit data stream. register name: tjbe1, tjbe2, tjbe3, tjbe4 register description: transmit jammed bit eight stuffing registers 1 to 4 register address: 104h, 105h, 106h, 107h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tjbe1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tjbe2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tjbe3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 tjbe4 the transmit jammed bit eight stuffing registers (tjbe 1?4) select which of the 24 t1 channels (or 32 e1 channels) to insert jammed bit eight st uffing. these registers are enabled by tcr4 .tjben. bits 7 to 0: transmit channels 1 to 32 ja mmed bit eight stuffing control bits (ch[1:32]) 0 = do not affect data in this channel. 1 = replace the channel with tjbes if the channel is all zeros.
DS26518 8-port t1/e1/j1 transceiver 197 of 286 register name: tdds1, tdds2, tdds3 register description: transmit dds zero code registers 1 to 3 register address: 108h, 109h, 10ah + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tdds1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tdds2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tdds3 the transmit dds zero code registers (tdds1?3) select wh ich of the 24 t1 channels to insert dds zero code stuffing. these registers are enabled by t1.tcr2 .tddsen. bits 7 to 0: transmit channels 1 to 24 dds zero code control bits (ch[1:32]) 0 = do not affect data in this channel. 1 = replace the channel with dds zero code stuffing if the channel is all zeros. register name: tfrid register description: transmit firmware revision id register register address: 161h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name fr7 fr6 fr5 fr4 fr3 fr2 fr1 fr0 default 0 0 0 0 0 0 0 0 bits 7 to 0: firmware revision (fr[7:0]). this read-only register reports the transmitter firmware revision. register name: t1tfdl register description: transmit fdl register register address: 162h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tfdl7 tfdl6 tfdl5 tfdl4 tfdl3 tfdl2 tfdl1 tfdl0 default 0 0 0 0 0 0 0 0 note: also used to insert fs fram ing pattern in d4 framing mode. the transmit fdl register (t1tfdl) c ontains the facility data link (fdl) in formation that is to be inserted on a byte basis into the outgoing t1 data stream. the lsb is transmitted first. in d4 mode, only the lower six bits are used. bit 7: transmit fdl bit 7 (tfdl7). msb of the transmit fdl code. bit 6: transmit fdl bit 6 (tfdl6) bit 5: transmit fdl bit 5 (tfdl5) bit 4: transmit fdl bit 4 (tfdl4) bit 3: transmit fdl bit 3 (tfdl3) bit 2: transmit fdl bit 2 (tfdl2) bit 1: transmit fdl bit 1 (tfdl1) bit 0: transmit fdl bit 0 (tfdl0). lsb of the transmit fdl code.
DS26518 8-port t1/e1/j1 transceiver 198 of 286 register name: t1tboc register description: transmit boc register register address: 163h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? tboc5 tboc4 tboc3 tboc2 tboc1 tboc0 default 0 0 0 0 0 0 0 0 bit 5: transmit boc bit 5 (tboc5). msb of the transmit boc code. bit 4: transmit boc bit 4 (tboc4) bit 3: transmit boc bit 3 (tboc3) bit 2: transmit boc bit 2 (tboc2) bit 1: transmit boc bit 1 (tboc1) bit 0: transmit boc bit 0 (tboc0). lsb of the transmit boc code.
DS26518 8-port t1/e1/j1 transceiver 199 of 286 register name: t1tslc1, t1tslc2, t1tslc3 (t1 mode) register description: transmit slc-96 data link registers 1 to 3 register address: 164h, 165h, 166h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name c8 c7 c6 c5 c4 c3 c2 c1 t1tslc1 m2 m1 s=0 s=1 s=0 c11 c10 c9 t1tslc2 s=1 s4 s3 s2 s1 a2 a1 m3 t1tslc3 note: see e1taf , e1tnaf , and e1tsiaf for e1 mode. register name: e1taf (e1 mode) register description: transmit align frame register register address: 164h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name si 0 0 1 1 0 1 1 default 0 0 0 1 1 0 1 1 bit 7: international bit (si) bit 6: frame alignment signal bit (0) bit 5: frame alignment signal bit (0) bit 4: frame alignment signal bit (1) bit 3: frame alignment signal bit (1) bit 2: frame alignment signal bit (0) bit 1: frame alignment signal bit (1) bit 0: frame alignment signal bit (1) register name: e1tnaf (e1 mode) register description: transmit non-align frame register register address: 165h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name si 1 a sa4 sa5 sa6 sa7 sa8 default 0 1 0 0 0 0 0 0 bit 7: international bit (si) bit 6: frame non-alignment signal bit (1) bit 5: remote alarm (used to transmit the alarm) (a) bit 4: additional bit 4 (sa4) bit 3: additional bit 5 (sa5) bit 2: additional bit 6 (sa6) bit 1: additional bit 7 (sa7) bit 0: additional bit 8 (sa8)
DS26518 8-port t1/e1/j1 transceiver 200 of 286 register name: e1tsiaf (e1 mode) register description: transmit si bits of the align frame register register address: 166h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tsif14 tsif12 tsif10 tsif8 tsif6 tsif4 tsif2 tsif0 default 0 0 0 0 0 0 0 0 bit 7: si bit of frame 14 (tsif14) bit 6: si bit of frame 12 (tsif12) bit 5: si bit of frame 10 (tsif10) bit 4: si bit of frame 8 (tsif8) bit 3: si bit of frame 6 (tsif6) bit 2: si bit of frame 4 (tsif4) bit 1: si bit of frame 2 (tsif2) bit 0: si bit of frame 0 (tsif0) register name: e1tsinaf (e1 mode only) register description: transmit si bits of th e non-align frame register register address: 167h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tsif15 tsif13 tsif11 tsif9 tsif7 tsif5 tsif3 tsif1 default 0 0 0 0 0 0 0 0 bit 7: si bit of frame 15 (tsif15) bit 6: si bit of frame 13 (tsif13) bit 5: si bit of frame 11 (tsif11) bit 4: si bit of frame 9 (tsif9) bit 3: si bit of frame 7 (tsif7) bit 2: si bit of frame 5 (tsif5) bit 1: si bit of frame 3 (tsif3) bit 0: si bit of frame 1 (tsif1)
DS26518 8-port t1/e1/j1 transceiver 201 of 286 register name: e1tra (e1 mode only) register description: transmit remote alarm register register address: 168h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name traf15 traf13 traf11 traf9 traf7 traf5 traf3 traf1 default 0 0 0 0 0 0 0 0 bit 7: remote alarm bit of frame 15 (traf15) bit 6: remote alarm bit of frame 13 (traf13) bit 5: remote alarm bit of frame 11 (traf11) bit 4: remote alarm bit of frame 9 (traf9) bit 3: remote alarm bit of frame 7 (traf7) bit 2: remote alarm bit of frame 5 (traf5) bit 1: remote alarm bit of frame 3 (traf3) bit 0: remote alarm bit of frame 1 (traf1) register name: e1tsa4 (e1 mode only) register description: transmit sa4 bits register register address: 169h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tsa4f15 tsa4f13 tsa4f11 tsa4f 9 tsa4f7 tsa4f5 tsa4f3 tsa4f1 default 0 0 0 0 0 0 0 0 bit 7: sa4 bit of frame 15 (tsa4f15) bit 6: sa4 bit of frame 13 (tsa4f13) bit 5: sa4 bit of frame 11 (tsa4f11) bit 4: sa4 bit of frame 9 (tsa4f9) bit 3: sa4 bit of frame 7 (tsa4f7) bit 2: sa4 bit of frame 5 (tsa4f5) bit 1: sa4 bit of frame 3 (tsa4f3) bit 0: sa4 bit of frame 1 (tsa4f1)
DS26518 8-port t1/e1/j1 transceiver 202 of 286 register name: e1tsa5 (e1 mode only) register description: transmit sa5 bits register register address: 16ah + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tsa5f15 tsa5f13 tsa5f11 tsa5f 9 tsa5f7 tsa5f5 tsa5f3 tsa5f1 default 0 0 0 0 0 0 0 0 bit 7: sa5 bit of frame 15 (tsa5f15) bit 6: sa5 bit of frame 13 (tsa5f13) bit 5: sa5 bit of frame 11 (tsa5f11) bit 4: sa5 bit of frame 9 (tsa5f9) bit 3: sa5 bit of frame 7 (tsa5f7) bit 2: sa5 bit of frame 5 (tsa5f5) bit 1: sa5 bit of frame 3 (tsa5f3) bit 0: sa5 bit of frame 1 (tsa5f1) register name: e1tsa6 (e1 mode only) register description: transmit sa6 bits register register address: 16bh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tsa6f15 tsa6f13 tsa6f11 tsa6f 9 tsa6f7 tsa6f5 tsa6f3 tsa6f1 default 0 0 0 0 0 0 0 0 bit 7: sa6 bit of frame 15 (tsa6f15) bit 6: sa6 bit of frame 13 (tsa6f13) bit 5: sa6 bit of frame 11 (tsa6f11) bit 4: sa6 bit of frame 9 (tsa6f9) bit 3: sa6 bit of frame 7 (tsa6f7) bit 2: sa6 bit of frame 5 (tsa6f5) bit 1: sa6 bit of frame 3 (tsa6f3) bit 0: sa6 bit of frame 1 (tsa6f1)
DS26518 8-port t1/e1/j1 transceiver 203 of 286 register name: e1tsa7 (e1 mode only) register description: transmit sa7 bits register register address: 16ch + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tsa7f15 tsa7f13 tsa7f11 tsa7f 9 tsa7f7 tsa7f5 tsa7f3 tsa7f1 default 0 0 0 0 0 0 0 0 bit 7: sa7 bit of frame 15 (tsa4f15) bit 6: sa7 bit of frame 13 (tsa7f13) bit 5: sa7 bit of frame 11 (tsa7f11) bit 4: sa7 bit of frame 9 (tsa7f9) bit 3: sa7 bit of frame 7 (tsa7f7) bit 2: sa7 bit of frame 5 (tsa7f5) bit 1: sa7 bit of frame 3 (tsa7f3) bit 0: sa7 bit of frame 1 (tsa7f1) register name: e1tsa8 (e1 mode only) register description: transmit sa8 bits register register address: 16dh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tsa8f15 tsa8f13 tsa8f11 tsa8f 9 tsa8f7 tsa8f5 tsa8f3 tsa8f1 default 0 0 0 0 0 0 0 0 bit 7: sa8 bit of frame 15 (tsa8f15) bit 6: sa8 bit of frame 13 (tsa8f13) bit 5: sa8 bit of frame 11 (tsa8f11) bit 4: sa8 bit of frame 9 (tsa8f9) bit 3: sa8 bit of frame 7 (tsa8f7) bit 2: sa8 bit of frame 5 (tsa8f5) bit 1: sa8 bit of frame 3 (tsa8f3) bit 0: sa8 bit of frame 1 (tsa8f1)
DS26518 8-port t1/e1/j1 transceiver 204 of 286 register name: tmmr register description: transmit master mode register register address: 180h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name frm_en init_done ? ? ? ? sftrst t1/e1 default 0 0 0 0 0 0 0 0 bit 7: framer enable (frm_en). this bit must be set to the desired state before writing init_done. 0 = framer disabled?held in low-power state. 1 = framer enabled?all features active. bit 6: initialization done (init_done). the user must set this bit once he has written the configur ation registers. the host is required to write or clea r all device registers prior to setting this bit. once init_done is set, the DS26518 will check the frm_en bit and, if enabled, will begin operation based on the initial configuration. bit 1: soft reset (sftrst). level sensitive ?soft? reset. should be ta ken high, then low to reset the transceiver. 0 = normal operation. 1 = reset the transceiver. note: this reset does not clear the registers. bit 0: transmitter t1/e1 mode select (t1/e1). sets operating mode for transmitter only! this bit must be written with the desired value prior to setting init_done. 0 = t1 operation. 1 = e1 operation.
DS26518 8-port t1/e1/j1 transceiver 205 of 286 register name: tcr1 (t1 mode) register description: transmit control register 1 register address: 181h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tjc tfpt tcpt tsse gb7s tb8zs tais trai default 0 0 0 0 0 0 0 0 note: see tcr1 for e1 mode. bit 7: transmit japanese crc-6 enable (tjc) 0 = use ansi/at&t:itu-t crc-6 calculation (normal operation). 1 = use japanese standard jt?g704 crc-6 calculation. bit 6: transmit f-bit pass through (tfpt) 0 = f bits sourced internally. 1 = f bits sampled at tsern ( t1.tcr2 .7 tfdls must be programmed to 0). bit 5: transmit crc pass through (tcpt) 0 = source crc-6 bits internally. 1 = crc-6 bits sampled at tsern during f-bit time. bit 4: transmit software signaling enable (tsse). this function is enabled by tb7zs ( t1.tcr2 .0). 0 = do not source signaling data from the ts1 ?16 registers regardless of the ssie1 ?4 registers. the ssie1 ?4 registers still define which channels are to have b7 stuffing performed. 1 = source signaling data as enabled by the ssie1 ?4 registers. bit 3: global bit 7 stuffing (gb7s). this function is enabled by tb7zs ( t1.tcr2 .0). 0 = allow the ssie1 ?4 registers to determine which channels cont aining all zeros are to be bit 7 stuffed. 1 = force bit 7 stuffing in all zero byte channels of that port, regardless of how the ssie1 ?4 registers are programmed. bit 2: transmit b8zs enable (tb8zs) 0 = b8zs disabled. 1 = b8zs enabled. bit 1: transmit alarm indication signal (tais) 0 = transmit data normally. 1 = transmit an unframed all-ones code at ttipn and tringn. bit 0: transmit remote alarm indication (trai) 0 = do not transmit remote alarm. 1 = transmit remote alarm.
DS26518 8-port t1/e1/j1 transceiver 206 of 286 register name: tcr1 (e1 mode) register description: transmit control register 1 register address: 181h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ttpt t16s tg802 tsis tsa1 thdb3 tais tcrc4 default 0 0 0 0 0 0 0 0 note: see tcr1 for t1 mode. bit 7: transmit time slot 0 pass through (ttpt) 0 = fas bits/sa bits/remote alarm sourced internally from the e1taf and e1tnaf registers. 1 = fas bits/sa bits/remote alarm sourced from tsern. bit 6: transmit time slot 16 data select (t16s). see section 9.9.4 on software signaling. 0 = time slot 16 determined by the ssie1 ?4 and thscs1 ?4 registers. 1 = source time slot 16 from ts1 ?16 registers. bit 5: transmit g.802 enable (tg802). see section 11.4 . 0 = do not force tchblkn high during bit 1 of time slot 26. 1 = force tchblkn high during bit 1 of time slot 26. bit 4: transmit international bit select (tsis) 0 = sample si bits at tsern pin. 1 = source si bits from e1taf and e1tnaf registers (in this mode, tcr1 .7 must be set to 0). bit 3: transmit signaling all ones (tsa1) 0 = normal operation. 1 = force time slot 16 in every frame to all ones. bit 2: transmit hdb3 enable (thdb3) 0 = hdb3 disabled. 1 = hdb3 enabled. bit 1: transmit ais (tais) 0 = transmit data normally. 1 = transmit an unframed all-ones code at ttipn and tringn. bit 0: transmit crc-4 enable (tcrc4) 0 = crc-4 disabled. 1 = crc-4 enabled.
DS26518 8-port t1/e1/j1 transceiver 207 of 286 register name: t1.tcr2 (t1 mode) register description: transmit control register 2 register address: 182h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tfdls tslc96 tddsen fbct2 fbct1 trais ? tb7zs default 0 0 0 0 0 0 0 0 note: see e1.tcr2 for e1 mode. bit 7: tfdl register select (tfdls) 0 = source fdl or fs bits from the internal tfdl register or the slc-96 data formatter ( t1.tcr2 .6). 1 = source fdl or fs bits from the internal hdlc controller. bit 6: transmit slc-96 (tslc96). set this bit to a one in slc-96 framing applications. must be set to source the slc-96 alignment pattern and data from the t1tslc1 ?3 registers. see section 9.9.4.3 for details. 0 = slc-96 insertion disabled. 1 = slc-96 insertion enabled. bit 5: transmit dds zero suppression enable (tddsen) 0 = no dds stuffing. 1 = dds stuffing enabled. force zero code 10011000 in all zero byte channels based on the channel select registers tdds1 ?3. bit 4: f-bit corruption type 2 (fbct2). setting this bit high enables the corruption of one ft (d4 framing mode) or fps (esf framing mode) bit in every 128 ft or fps bits as long as the bit remains set. bit 3: f-bit corruption type 1 (fbct1). a low-to-high transition of this bit causes the next three consecutive ft (d4 framing mode) or fps (esf framing mode) bits to be corrupted causing the remote end to experience a loss of synchronization. bit 2: transmit rai select (trais) 0 = transmit rai is t1. d4?zeros in bit 2 of all channels. esf?00ff pattern in the fdl. 1 = transmit rai is j1. d4?a one in the s-bit position of frame 12. esf?all ones in fdl. note: this bit only selects the type of remote alarm to send. to enable transmission of remote alarm, set tcr1 .trai. bit 0: transmit-side bit 7 zero suppression enable (tb7zs) 0 = no stuffing occurs. 1 = force bit 7 to a one as determined by the gb7s bit at tcr1 .3.
DS26518 8-port t1/e1/j1 transceiver 208 of 286 register name: e1.tcr2 (e1 mode) register description: transmit control register 2 register address: 182h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name aebe aais ara ? ? ? ? ? default 0 0 0 0 0 0 0 0 note: see t1.tcr2 for t1 mode. bit 7: automatic e-bit enable (aebe) 0 = e-bits not automatically set in the transmit direction. 1 = e-bits automatically set in the transmit direction. bit 6: automatic ais generation (aais) 0 = disabled 1 = enabled bit 5: automatic remote alarm generation (ara) 0 = disabled 1 = enabled
DS26518 8-port t1/e1/j1 transceiver 209 of 286 register name: tcr3 register description: transmit control register 3 register address: 183h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? tcss1 tcss0 mfrs tfm ibpv tloop ? ? tcss1 tcss0 mfrs ? ibpv crc4 default 0 0 0 0 0 0 0 0 bits 5 and 4 : transmit clock s ource select 1 and 0 (tcss[1:0]) tcss1 tcss0 transmit clock source 0 0 the tclkn pin is always t he source of transmit clock. 0 1 switch to the clock present at rclkn when the si gnal at the tclkn pin fails to transition after 1 channel time. 1 0 reserved. 1 1 use the signal present at rclkn as the transm it clock. the tclkn pin is ignored (loop time). bit 3: multiframe reference select (mfrs). this bit selects the source for the transmit formatter multiframe boundary. 0 = normal operation. transmit multiframe boundary is determined by 'line-side' counters referenced to tsyncn when tsyncn is an input. free-running when tsyncn is an output. 1 = pass-forward operation. tx multiframe boundary determined by 'system-side' counters referenced to tssyncion (input mode3), which is then passed forw ard to the line side clock domain. this mode can only be used when the transmit elastic store is enabled with a synchronous backplane (i.e., no frame slips allowed). this mode must be used to allow tx hardwar e signaling insertion while the tx elastic store is enabled. bit 2: transmit frame mode select (tfm) (t1 mode only) 0 = esf framing mode. 1 = d4 framing mode. bit 1: insert bpv (ibpv). a 0-to-1 transition on this bit will cause a single bipolar violation (bpv) to be inserted into the transmit data stream. once this bit has been t oggled from a 0 to a 1, the device waits for the next occurrence of three consecutive ones to insert the bpv. this bit must be cleared and set again for a subsequent error to be inserted. bit 0 (t1 mode): transmit loop code enable (tloop). see section 9.9.15 for details. 0 = transmit data normally. 1 = replace normal transmitted data with repeating code as defined in registers t1tcd1 and t1tcd2 . bit 0 (e1 mode): crc- 4 recalculate (crc4r) 0 = transmit crc-4 generation and in sertion operates in normal mode. 1 = transmit crc-4 generation ope rates according to g.706 intermediate path recalculation method.
DS26518 8-port t1/e1/j1 transceiver 210 of 286 register name: tiocr register description: transmit i/o configuration register register address: 184h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tclkinv tsyncinv tssyncinv tsclkm tssm tsio tsdw tsm tclkinv tsyncinv tssyncinv tsclkm tssm tsio ? tsm default 0 0 0 0 0 0 0 0 bit 7: tclkn invert (tclkinv) 0 = no inversion. 1 = invert. bit 6: tsyncn invert (tsyncinv) 0 = no inversion. 1 = invert. bit 5: tssyncion (input mode only) invert (tssyncinv) 0 = no inversion. 1 = invert. bit 4: tsysclkn mode select (tsclkm) 0 = if tsysclkn is 1.544mhz. 1 = if tsysclkn is 2.048/4.096/8.192m hz or ibo enabled (see section 9.8.2 for details on ibo function). bit 3: tssyncion mode select (tssm). selects frame or multiframe mode for the tssyncion pin. 0 = frame mode. 1 = multiframe mode. bit 2: tsyncn i/o select (tsio) 0 = tsyncn is an input. 1 = tsyncn is an output. bit 1: tsyncn double-wide (tsdw) (t1 mode only) ( note: this bit must be set to zero when tsm = 1 or when tsio = 0.) 0 = do not pulse double-wide in signaling frames. 1 = do pulse double-wide in signaling frames. bit 0: tsyncn mode select (tsm). selects frame or multiframe mode for the tsyncn pin. 0 = frame mode. 1 = multiframe mode.
DS26518 8-port t1/e1/j1 transceiver 211 of 286 register name: tescr register description: transmit elastic store control register register address: 185h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tdatfmt tgclken ? tszs tesalgn tesr tesmdm tese default 0 0 0 0 0 0 0 0 note: bits 6 and 7 are used for fractional backplane support. see section 9.8.5 . bit 7: transmit channel data format (tdatfmt) 0 = 64kbps (data contained in all 8 bits). 1 = 56kbps (data contained in 7 out of the 8 bits). bit 6: transmit gapped clock enable (tgclken) 0 = tchclk functions normally. 1 = enable gapped bit clock output on tchclkn. bit 4: transmit slip zone select (tszs). this bit determines the minimum distance allowed between the elastic store read and write pointers before forcing a controlled slip. this bit is only applies during t1 to e1 or e1 to t1 conversion applications. 0 = force a slip at 9 bytes or less of separation (used for clustered blank channels). 1 = force a slip at 2 bytes or less of se paration (used for distributed blank channels). bit 3: transmit elastic store align (tesalgn). setting this bit from a zero to a one will force the transmit elastic store?s write/read pointers to a minimum separation of half a frame. no action will be taken if the pointer separation is already greater or equal to half a frame. if pointer separati on is less than half a frame, the command will be executed and the data will be disrupted. should be toggl ed after tsysclkn has been a pplied and is stable. must be cleared and set again for a subsequent align. bit 2: transmit elastic store reset (tesr). setting this bit from a zero to a one will force the read pointer into the same frame that the write pointer is exiting, minimi zing the delay through the elastic store. if this command should place the pointers within the slip zone (see bit 4), then an immediate slip will occur and the pointers will move back to opposite frames. should be toggled after tsysclkn has been app lied and is stable. do not leave this bit set high. bit 1: transmit elastic stor e minimum delay mode (tesmdm) 0 = elastic stores operate at full two-frame depth. 1 = elastic stores operate at 32-bit depth. bit 0: transmit elastic store enable (tese) 0 = elastic store is bypassed. 1 = elastic store is enabled.
DS26518 8-port t1/e1/j1 transceiver 212 of 286 register name: tcr4 register description: transmit control register 4 register address: 186h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ualaw binv1 binv0 tjben traim taism tc1 tc0 ualaw binv1 binv0 tjben ? ? ? ? default 0 0 0 0 0 0 0 0 bit 7: u-law or a-law digital milliwatt code select (ualaw) 0 = u-law code is inserted based on tdmwex registers. 1 = a-law code is inserted based on tdmwex registers. bits 6 and 5: transmit bit inversion (binv[1:0]) 00 = no inversion. 01 = invert framing. 10 = invert signaling. 11 = invert payload. bit 4: transmit jammed bit 8 suppression enable (tjben) 0 = no stuffing enabled. 1 = jammed bit 8 suppression enabled. this forces bit 8 to a one as determined by tjbe1 ?4 registers and bit 7 to a one in t1 signaling frames. bits 3: transmit rai mode (traim) (t1 mode only). determines the pattern sent when trai ( tcr1 .0) is activated in esf frame mode only. 0 = transmit normal rai when tcr1 .rai = 1 1 = if t1 esf mode, transmit rai-ci (t1.403) when tcr1 .rai = 1 bits 2 : transmit ais mode (taism) (t1 mode only). determines the pattern sent when tais ( tcr1 .1) is activated. 0 = transmit normal ais (unframed all ones) upon activation with tcr1 .1. 1 = transmit ais-ci (t1.403) upon activation with tcr1 .1. bits 1 and 0 : transmit code length de finition bits (tc[1:0]) (t1 mode only) tc1 tc0 length selected 0 0 5 bits 0 1 6 bits : 3 bits 1 0 7 bits 1 1 16 bits : 8 bits : 4 bits : 2 bits : 1 bit
DS26518 8-port t1/e1/j1 transceiver 213 of 286 register name: thfc register description: transmit hdlc fifo control register register address: 187h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? tflwm1 tflwm0 default 0 0 0 0 0 0 0 0 bits 1 and 0: transmit hdlc fifo low watermark select (tflwm[1:0]) tflwm1 tflwm0 transmit fifo watermark 0 0 4 bytes 0 1 16 bytes 1 0 32 bytes 1 1 48 bytes register name: tiboc register description: transmit interleave bus operation control register register address: 188h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ibosel iboen ? ? ? default 0 0 0 0 0 0 0 0 bit 4: interleave bus operation select (ibosel). this bit selects channel or frame interleave mode. 0 = channel interleave. 1 = frame interleave. bit 3: interleave bus operation enable (iboen) 0 = interleave bus operation disabled. 1 = interleave bus operation enabled. register name: tds0sel register description: transmit ds0 channel monitor select register register address: 189h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? tcm4 tcm3 tcm2 tcm1 tcm0 default 0 0 0 0 0 0 0 0 bits 4 to 0: transmit channel monitor bits (tcm[4:0]). tcm0 is the lsb of a 5-bit channel select that determines which transmit channel data will appear in the tds0m register. channels 1 through 32 are represented by a 5-bit bcd code from 0 to 31. tcm[0:4] = all 0s selects channel 1, tcm[0:4] = 11111 selects channel 32.
DS26518 8-port t1/e1/j1 transceiver 214 of 286 register name: txpc register description: transmit expansion port control register register address: 18ah + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? tbpdir tbpfus tbpen default 0 0 0 0 0 0 0 0 bit 2: transmit bert port direction control (tbpdir) 0 = normal (line) operation. transmit bert port sources data into the transmit path. 1 = system (backplane) operation. transmit bert por t sources data into the receive path (rsern). in this mode, the data from the bert is muxed into the receive path. bit 1: transmit bert port framed/unframed select (tbpfus) 0 = the DS26518?s transmit bert will not clock data into the f-bit position (framed). 1 = the DS26518?s transmit bert will clock data into the f-bit position (unframed). bit 0: transmit bert port enable (tbpen) 0 = transmit bert port is not active. 1 = transmit bert port is active.
DS26518 8-port t1/e1/j1 transceiver 215 of 286 register name: tbpbs register description: transmit bert port bit suppress register register address: 18bh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name bpbse8 bpbse7 bpbse6 bpbse5 bpbse4 bpbse3 bpbse2 bpbse1 default 0 0 0 0 0 0 0 0 bit 7: transmit channel bit 8 suppress (bpbse8). msb of the channel. set to one to stop this bit from being used. bit 6: transmit channel bit 7 suppress (bpbse7). set to one to stop this bit from being used. bit 5: transmit channel bit 6 suppress (bpbse6). set to one to stop this bit from being used. bit 4: transmit channel bit 5 suppress (bpbse5). set to one to stop this bit from being used. bit 3: transmit channel bit 4 suppress (bpbse4). set to one to stop this bit from being used. bit 2: transmit channel bit 3 suppress (bpbse3). set to one to stop this bit from being used. bit 1: transmit channel bit 2 suppress (bpbse2). set to one to stop this bit from being used. bit 0: transmit channel bit 1 suppress (bpbse1). lsb of the channel. set to one to stop this bit from being used. register name: tsyncc register description: transmit synchronizer control register register address: 18eh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? tsen synce resync ? ? ? ? crc4 tsen synce resync default 0 0 0 0 0 0 0 0 bit 3: crc-4 enable (crc4) (e1 mode only) 0 = do not search for the crc-4 multiframe word. 1 = search for the crc-4 multiframe word. bit 2: transmit synchronizer enable (tsen) 0 = transmit synchronizer disabled. 1 = transmit synchronizer enabled. bit 1: sync enable (synce) 0 = auto resync enabled. 1 = auto resync disabled. bit 0: resynchronize (resync). when toggled from low to high, a resync hronization of the transmit-side framer is initiated. must be cleared and set again for a subsequent resync.
DS26518 8-port t1/e1/j1 transceiver 216 of 286 register name: tls1 register description: transmit latched status register 1 register address: 190h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tesf tesem tslip tslc96 ? tmf lotcc lotc tesf tesem tslip ? taf tmf lotcc lotc default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can cause interrupts. bit 7: transmit elastic store full event (tesf). set when the transmit elastic store buffer fills and a frame is deleted. bit 6: transmit elastic store empty event (tesem). set when the transmit elastic store buffer empties and a frame is repeated. bit 5: transmit elastic store slip occurrence event (tslip). set when the transmit elastic store has either repeated or deleted a frame. bit 4: transmit slc-96 multiframe event (tslc96) (t1 mode only). when enabled by t1.tcr2 .6, this bit will set once per slc-96 multiframe (72 frames) to al ert the host that new data may be written to the t1tslc1 ?3 registers. see section 9.9.4.3 for more information. bit 3: transmit align frame event (taf) (e1 mode only). set every 250 s to alert the host that the e1taf and e1tnaf registers need to be updated. bit 2: transmit multiframe event (tmf). in t1 mode, this bit is set every 1.5ms on d4 mf boundaries or every 3ms on esf mf boundaries. in e1 operation, this but is set every 2ms (regardless if crc-4 is enabled) on transmit multiframe boundaries. used to alert the host that signaling data needs to be updated. bit 1: loss of transmit clock condition clear (lotcc). set when the lotc condition has cleared (a clock has been sensed at the tclkn pin). bit 0: loss of transmit clock condition (lotc). set when the tclkn pin has not transitioned for approximately 3 clock periods. will force the lotc pin high if enabled. this bit can be cleared by the hos t even if the condition is still present. the lotc pin will remain high while the conditi on exists, even if the host has cleared the status bit. if enabled by tim1 .0, the intb pin will transition low when this bit is set, and transition high when this bit is cleared (if no other unmasked interrupt conditions exist).
DS26518 8-port t1/e1/j1 transceiver 217 of 286 register name: tls2 register description: transmit latched status register 2 (hdlc) register address: 191h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? tfdle tudr tmend tlwms tnfs ? ? ? ? tudr tmend tlwms tnfs default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can create interrupts. bit 4: transmit fdl register empty (tfdle) (t1 mode only). set when the tfdl register has shifted out all 8 bits. useful if the user wants to manually use the tfdl register to send messages, instead of using the hdlc or boc controller circuits. bit 3: transmit fifo underrun event (tudr). set when the transmit fifo empt ies out without having seen the tmend bit set. an abort is automatically sent. bit 2: transmit message end event (tmend). set when the transmit hdlc controller has finished sending a message. bit 1: transmit fifo below low watermark set condition (tlwms). set when the transmit 64-byte fifo empties beyond the low watermark as defined by the transmit low watermark bits (tlwm), rising edge detect of tlwm. bit 0: transmit fifo not full set condition (tnfs). set when the transmit 64-byte fifo has at least one empty byte available for write. rising edge detect of tnf. indicates change of state from full to not full. register name: tls3 register description: transmit latched status register 3 (synchronizer) register address: 192h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? lof lofd default 0 0 0 0 0 0 0 0 note: some bits in this register are latched and can create interrupts. bit 1: loss of frame (lof). a real-time bit that indicates that the tr ansmit synchronizer is searching for the sync pattern in the incoming data stream. bit 0: loss of frame synchronization detect (lofd). this latched bit is set when the transmit synchronizer is searching for the sync pattern in the incoming data stream.
DS26518 8-port t1/e1/j1 transceiver 218 of 286 register name: tiir register description: transmit interrupt information register register address: 19fh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? tls3 tls2 tls1 default 0 0 0 0 0 0 0 0 the interrupt information register provides an indication of which status registers are generating an interrupt. when an interrupt occurs, the host can read ti ir to quickly identify which of the tr ansmit status registers are causing the interrupt(s). these are real-time registers in that the bits will clear once the appropriate interrupt has been serviced and cleared. bit 2: transmit latched status register 3 interrupt status (tls3) 0 = no interrupt pending. 1 = interrupt pending. bit 1: transmit latched status register 2 interrupt status (tls2) 0 = no interrupt pending. 1 = interrupt pending. bit 0: transmit latched status register 1 interrupt status (tls1) 0 = no interrupt pending. 1 = interrupt pending.
DS26518 8-port t1/e1/j1 transceiver 219 of 286 register name: tim1 register description: transmit interrupt mask register 1 register address: 1a0h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tesf tesem tslip tslc96 ? tmf lotcc lotc tesf tesem tslip ? taf tmf lotcc lotc default 0 0 0 0 0 0 0 0 bit 7: transmit elastic store full event (tesf) 0 = interrupt masked. 1 = interrupt enabled. bit 6: transmit elastic store empty event (tesem) 0 = interrupt masked. 1 = interrupt enabled. bit 5: transmit elastic store slip occurrence event (tslip) 0 = interrupt masked. 1 = interrupt enabled. bit 4: transmit slc96 multiframe event (tslc96) (t1 mode only) 0 = interrupt masked. 1 = interrupt enabled. bit 3: transmit align frame event (taf) (e1 mode only) 0 = interrupt masked. 1 = interrupt enabled. bit 2: transmit multiframe event (tmf) 0 = interrupt masked. 1 = interrupt enabled. bit 1: loss of transmit clock clear condition (lotcc) 0 = interrupt masked. 1 = interrupt enabled. bit 0: loss of transmit clock condition (lotc) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 220 of 286 register name: tim2 register description: transmit interrupt mask register 2 register address: 1a1h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? tfdle tudr tmend tlwms tnfs ? ? ? ? tudr tmend tlwms tnfs default 0 0 0 0 0 0 0 0 bit 4: transmit fdl register empty (tfdle) (t1 mode only) 0 = interrupt masked. 1 = interrupt enabled. bit 3: transmit fifo underrun event (tudr) 0 = interrupt masked. 1 = interrupt enabled. bit 2: transmit message end event (tmend) 0 = interrupt masked. 1 = interrupt enabled. bit 1: transmit fifo below low watermark set condition (tlwms) 0 = interrupt masked. 1 = interrupt enabled. bit 0: transmit fifo not full set condition (tnfs) 0 = interrupt masked. 1 = interrupt enabled. register name: tim3 register description: transmit interrupt mask register 3 (synchronizer) register address: 1a2h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? ? ? ? lofd default 0 0 0 0 0 0 0 0 bit 0: loss of frame synchronization detect (lofd) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 221 of 286 register name: t1tcd1 (t1 mode only) register description: transmit code definition register 1 register address: 1ach + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 bit 7: transmit code definition bit 7 (c7). first bit of the repeating pattern. bit 6: transmit code definition bit 6 (c6) bit 5: transmit code definition bit 5 (c5) bit 4: transmit code definition bit 4 (c4) bit 3: transmit code definition bit 3 (c3) bit 2: transmit code definition bit 2 (c2). a don?t care if a 5-bit length is selected. bit 1: transmit code definition bit 1 (c1). a don?t care if a 5- or 6-bit length is selected. bit 0: transmit code definition bit 0 (c0). a don?t care if a 5-, 6-, or 7-bit length is selected. register name: t1tcd2 (t1 mode only) register description: transmit code definition register 2 register address: 1adh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name c7 c6 c5 c4 c3 c2 c1 c0 default 0 0 0 0 0 0 0 0 bit 7: transmit code definition bit 7 (c7). a don?t care if a 5-, 6-, or 7-bit length is selected. bit 6: transmit code definition bit 6 (c6). a don?t care if a 5-, 6-, or 7-bit length is selected. bit 5: transmit code definition bit 5 (c5). a don?t care if a 5-, 6-, or 7-bit length is selected. bit 4: transmit code definition bit 4 (c4). a don?t care if a 5-, 6-, or 7-bit length is selected. bit 3: transmit code definition bit 3 (c3). a don?t care if a 5-, 6-, or 7-bit length is selected. bit 2: transmit code definition bit 2 (c2). a don?t care if a 5-, 6-, or 7-bit length is selected. bit 1: transmit code definition bit 1 (c1). a don?t care if a 5-, 6-, or 7-bit length is selected. bit 0: transmit code definition bit 0 (c0). a don?t care if a 5-, 6-, or 7-bit length is selected.
DS26518 8-port t1/e1/j1 transceiver 222 of 286 register name: trts2 register description: transmit real-time status register 2 (hdlc) register address: 1b1h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? ? ? tempty tfull tlwm tnf default 0 0 0 0 0 0 0 0 note: all bits in this register are real time. bit 3: transmit fifo empty (tempty). a real-time bit that is set high when the fifo is empty. bit 2: transmit fifo full (tfull). a real-time bit that is set high when the fifo is full. bit 1: transmit fifo below low watermark condition (tlwm). set when the transmit 64-byte fifo empties beyond the low watermark as defined by t he transmit low watermark bits (tlwm). bit 0: transmit fifo not full condition (tnf). set when the transmit 64-byte fifo has at least one byte available. register name: tfba register description: transmit hdlc fifo buffer available register register address: 1b3h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? tfba6 tfba5 tfba4 tfba3 tfba2 tfba1 tfba0 default 0 0 0 0 0 0 0 0 bits 6 to 0: transmit fifo bytes available (tfba6 to tfba0). tfba0 is the lsb. register name: thf register description: transmit hdlc fifo register register address: 1b4h + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name thd7 thd6 thd5 thd4 thd3 thd2 thd1 thd0 default 0 0 0 0 0 0 0 0 bit 7: transmit hdlc data bit 7 (thd7). msb of an hdlc packet data byte. bit 6: transmit hdlc data bit 6 (thd6) bit 5: transmit hdlc data bit 5 (thd5) bit 4: transmit hdlc data bit 4 (thd4) bit 3: transmit hdlc data bit 3 (thd3) bit 2: transmit hdlc data bit 2 (thd2) bit 1: transmit hdlc data bit 1 (thd1) bit 0: transmit hdlc data bit 0 (thd0). lsb of an hdlc packet data byte.
DS26518 8-port t1/e1/j1 transceiver 223 of 286 register name: tds0m register description: transmit ds0 monitor register register address: 1bbh + (200h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name b1 b2 b3 b4 b5 b6 b7 b8 default 0 0 0 0 0 0 0 0 bits 7 to 0: transmit ds0 channel bits (b[1:8]). transmit channel data that has been selected by the tds0sel register. b8 is the lsb of the ds0 channel (last bit to be transmitted). register name: tbcs1, tbcs2, tbcs3, tbcs4 register description: transmit blank channel select registers 1 to 4 register address: 1c0h, 1c1h, 1c2h, 1c3h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 named ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tbcs1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tbcs2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tbcs3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 tbcs4 (e1 mode only) bits 7 to 0: transmit blank channel select for channels 1 to 32 (ch[1:32]) 0 = transmit tsern data from this channel. 1 = ignore tsern data from this channel. note that when two or more sequential channels are chosen to be ignored, the receive slip zone select bit should be set to zero. if the ignore channels are distributed (such as 1, 5, 9, 13, 17, 21, 25, 29) then the rszs bit can be set to one, which may provide a lower occurrence of slips in certain applications.
DS26518 8-port t1/e1/j1 transceiver 224 of 286 register name: tcbr1, tcbr2, tcbr3, tcbr4 register description: transmit channel blocking registers 1 to 4 register address: 1c4h, 1c5h, 1c6h, 1c7h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tcbr1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tcbr2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tcbr3 ch32 ch31 ch30 ch 29 ch28 ch27 ch26 ch25 (f-bit) tcbr4 (e1 mode only)* bits 7 to 0: transmit channels 1 to 32 channel blocking control bits (ch[1:32]). 0 = force the tchblkn pin to remain low during this channel time. 1 = force the tchblkn pin high during this channel time. * note that tcbr4 has two functions: when 2.048mhz backplane mode is selected, this regi ster allows the user to enable the channel blocking signal for any of the 32 possible backplane channels. when 1.544mhz backplane mode is selected, the lsb of this register determi nes whether or not the tchblkn signal will pulse high during the f-bit time: tcbr4.0 = 0, do not pulse tchblkn during the f-bit. tcbr4.0 = 1, pulse tchblkn during the f-bit. in this mode tcbr4.1 to tcbr4.7 should be set to 0. register name: thscs1, thscs2, thscs3, thscs4 register description: transmit hardware-signaling channel select registers 1 to 4 register address: 1c8h, 1c9h, 1cah, 1cbh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 thscs1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 thscs2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 thscs3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 thscs4 (e1 mode only)* bits 7 to 0: transmit hardware-signaling cha nnel select for channels 1 to 32 (ch[1:32]). these bits determine which channels have signaling data inserted from the tsign pin into the tsern pcm data. 0 = do not source signaling data from the tsign pin for this channel. 1 = source signaling data from the tsign pin for this channel. * note that thscs4 is only used in 2.048mhz backplane applications.
DS26518 8-port t1/e1/j1 transceiver 225 of 286 register name: tgccs1, tgccs2, tgccs3, tgccs4 register description: transmit gapped clock channel select registers 1 to 4 register address: 1cch, 1cdh, 1ceh, 1cfh + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tgccs1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tgccs2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tgccs3 ch32 ch31 ch30 ch 29 ch28 ch27 ch26 ch25 (f-bit) tgccs4 (e1 mode only)* bits 7 to 0: transmit channels 1 to 32 gapped clock channel select bits (ch[1:32]) 0 = no clock is present on tchclk during this channel time 1 = force a clock on tchclk during this channel time . the clock will be synchronous with tclkn if the elastic store is disabled, and synchronous with tsysclkn if the elastic store is enabled. * note that tgccs4 has two functions: when 2.048mhz backplane mode is selected, this regi ster allows the user to enable the gapped clock on tchclk for any of the 32 possible backplane channels. when 1.544mhz backplane mode is selected, the lsb of this register determines w hether or not a clock is generated on tchclk during the f-bit time: tgccs4.0 = 0, do not generate a clock during the f-bit. tgccs4.0 = 1, generate a clock during the f-bit. in this mode tgccs4.1 to tgccs4.7 should be set to 0. register name: pcl1, pcl2, pcl3, pcl4 register description: per-channel loopback enable registers 1 to 4 register address: 1d0h, 1d1h, 1d2h, 1d3h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # 7 6 5 4 3 2 1 0 name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 pcl1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 pcl2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 pcl3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 pcl4 (e1 mode only) bits 7 to 0: per-channel loopback enable for channels 1 to 32 (ch[1:32]) 0 = loopback disabled. 1 = enable loopback. source data from the corresponding receive channel.
DS26518 8-port t1/e1/j1 transceiver 226 of 286 register name: tbpcs1, tbpcs2, tbpcs3, tbpcs4 register description: transmit bert port channel select registers register address: 1d4h, 1d5h, 1d6h, 1d7h + (200h x (n - 1)) : where n = 1 to 8 (msb) (lsb) bit # name ch8 ch7 ch6 ch5 ch4 ch3 ch2 ch1 tbpcs1 ch16 ch15 ch14 ch13 ch12 ch11 ch10 ch9 tbpcs2 ch24 ch23 ch22 ch21 ch20 ch19 ch18 ch17 tbpcs3 ch32 ch31 ch30 ch29 ch28 ch27 ch26 ch25 tbpcs4 (e1 mode only) setting any of the ch[1:32] bits in the tbpcs1 to t bpcs4 registers will enable the transmit bert clock for the associated channel time, and allow mapping of the selected channel data out of the receive bert port. multiple or all channels may be selected simultaneously.
DS26518 8-port t1/e1/j1 transceiver 227 of 286 10.5 liu register definitions table 10-15. liu register set address name description r/w 1000h ltrcr liu transmit receive control register r/w 1001h ltipsr liu transmit impedance and pulse shape selection register r/w 1002h lmcr liu maintenance control register r/w 1003h lrsr liu real status register r 1004h lsimr liu status interrupt mask register r/w 1005h llsr liu latched status register r/w 1006h lrsl liu receive signal level register r 1007h lrismr liu receive impedance and sensit ivity monitor register r/w 1008h lrcr liu receive control register r/w 1009h?101fh ? reserved ? note: reserved registers should only be written with all zeros.
DS26518 8-port t1/e1/j1 transceiver 228 of 286 register name: ltrcr register description: liu transmit receive control register register addresses: 1000h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? rhpm jads1 jads0 japs1 japs0 t1j1e1s lsc default 0 0 0 0 0 0 0 0 bit 6: receive hitless protection mode (rhpm). 0 = normal operation using software for hitless protection (rimpon). 1 = hitless protection switching mode using txenable pin. if the txenable pin is low and this bit is set to one, the receive liu will present a high impedance to the line, overriding the receive impedance selection register bits lrismr . rimpm[2:0]. bits 5 and 4 : jitter attenuator depth select (jads[1:0]) jads1 jads0 function 0 0 jitter attenuator fifo depth 128 bits. 0 1 jitter attenuator fifo depth 64 bits. 1 0 jitter attenuator fifo depth 32 bits. 1 1 jitter attenuator fifo depth 16 bits (used for delay sens itive applications). bits 3 and 2: jitter attenuator position select (japs[1:0]). these bits are used to select the position of the jitter attenuator. japs1 japs0 function 0 0 jitter attenuator in the receive path. 0 1 jitter attenuator in the transmit path. 1 0 jitter attenuator disabled. 1 1 jitter attenuator disabled. bit 1: t1j1e1 selection (t1j1e1s). this bit configures the liu for e1 or t1/j1 operation. 0 = e1 1 = t1 or j1 bit 0: los selection criteria (lsc). this bit is used for liu los selection criteria. e1 mode 0 = g.775 1 = ets 300 233 t1/j1 mode 0 = t1.231 1 = t1.231
DS26518 8-port t1/e1/j1 transceiver 229 of 286 register name: ltipsr register description: liu transmit impedance and pulse shape selection register register address: 1001h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tg703 timpton timpl1 timpl0 ? l2 l1 l0 default 0 0 0 0 0 0 0 0 bit 7: transmit g.703 synchronization clock (tg703) 0 = normal transmitter mode. 1 = g.703 2.048mhz clock transmitted on ttipn and tringn. bit 6: transmit impedance on (timpton) 0 = disable transmit terminating impedance. 1 = enable transmit terminating impedance. bits 5 and 4: transmit load impedance 1 and 0 (timpl[1:0]). these bits are used to select the transmit load impedance. these must be set to match the cable impedance. even if the internal load impedance is turned off (via timptoff); the external cable impedance has to be spec ified for optimum operation. for j1 applications, use 110 . see table 10-16 . bits 2 to 0: line build-out select 2 to 0 (l[2:0]) . used to select the transmit waveshape. the waveshape has a voltage level and load impedance associated with it once t he t1/j1 or e1 selection is made by settings in the ltrcr register. see table 10-17 . table 10-16. transmit loa d impedance selection timpl1 timplo impedance selection 0 0 75 0 1 100 1 0 110 1 1 120 table 10-17. transmit pulse shape selection l2 l1 l0 mode impedance nominal voltage 0 0 0 e1 75 2.37v 0 0 1 e1 120 3.0v l2 l1 l0 mode cable length max allowed cable loss 0 0 0 t1/j1 dsx-1/0db csu, 0ft?133ft abam 100 0.6db 0 0 1 t1/j1 dsx-1, 133ft?266ft abam 100 1.2db 0 1 0 t1/j1 dsx-1, 266ft?399ft abam 100 1.8db 0 1 1 t1/j1 dsx-1, 399ft?533ft abam 100 2.4db 1 0 0 t1/j1 dsx-1, 533ft?655ft abam 100 3.0db 1 0 1 t1/j1 -7.5db csu ? 1 1 0 t1/j1 -15db csu ? 1 1 1 t1/j1 -22.5db csu ?
DS26518 8-port t1/e1/j1 transceiver 230 of 286 register name: lmcr register description: liu maintenance control register register address: 1002h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tais atais lb2 lb1 lb0 tpde rpde te default 0 0 0 0 0 0 0 0 bit 7: manual transmit ais (tais). alarm indication signal (ais) is sent using mclk as the reference clock. the transmit data coming from the framer is ignored. 0 = tais is disabled. 1 = output an unframed all-ones pa ttern (ais) at ttipn and tringn. bit : automatic transmit ais (atais) 0 = atais is disabled. 1 = automatically transmit ais on the occurrence of an liu los. bits 5 to 3: loopback selection (lb[2:0]. see figure 9-26 for more details on each loopback. lb2 lb1 lb0 loopback selection 0 0 0 no loopback selected 0 0 1 remote loopback 2 (includes jitter attenuator) 0 1 0 analog loopback 0 1 1 remote loopback 1 (no jitter attenuator) 1 0 0 local loopback (includes jitter attenuator) 1 0 1 dual loopback?remote loopback 1 and local loopback (jitter attenuator is included in local loopback) 1 1 0 reserved 1 1 1 reserved bit 2: transmit power-down enable (tpde) 0 = transmitter power enabled. 1 = transmitter powered down. ttipn/tringn outputs are high impedance. bit 1: receiver power-down enable ( rpde) 0 = receiver power enabled. 1 = receiver powered down. bit 0: transmit enable (te). this function is overridden by the txenable pin. 0 = ttipn/tringn outputs are high impedance. 1 = ttipn/tringn outputs enabled.
DS26518 8-port t1/e1/j1 transceiver 231 of 286 register name: lrsr register description: liu real status register register address: 1003h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? ? oeq ueq rscs tscs ocs loss default 0 0 0 0 0 0 0 0 bit 5: over equalized (oeq). the equalizer is over equalized. this can happen if there very large unexpected resistive loss. this could result if monitor mode is used and the device is not placed in monitor mode. this indicator provides more qualitative information to the receive loss indicators. bit 4: under equalized (ueq). the equalizer is under equalized. a signal with a very high resistive gain is being applied. this indicator provides more qualitativ e information to the receive loss indicators. bit 3: receive short-ci rcuit status (rscs). a real-time bit set when the liu detects that the rtipn and rringn inputs are short-circuited. the load resistance has to be 25 (typically) or less for short circuit detection. bit 2: transmit short-circuit status (tscs). a real-time bit set when the liu detects that the ttipn and tringn outputs are short-circuit ed. the load resistance has to be 25 (typically) or less for short circuit detection. bit 1: open-circuit status (ocs). a real-time bit that is set when the liu detects that the ttipn and tringn outputs are open-circuited. bit 0: loss of signal status ( loss). a real-time bit that is set when the liu detects an los condition at rtipn and rringn.
DS26518 8-port t1/e1/j1 transceiver 232 of 286 register name: lsimr register description: liu status interrupt mask register register address: 1004h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name jaltcim occim sccim loscim jaltsim ocdim scdim losdim default 0 0 0 0 0 0 0 0 bit 7: jitter attenuator limit trip clear interrupt mask (jaltcim) 0 = interrupt masked. 1 = interrupt enabled. bit 6: open-circuit clear interrupt mask (occim) 0 = interrupt masked. 1 = interrupt enabled. bit 5: short-circuit clear interrupt mask (sccim) 0 = interrupt masked. 1 = interrupt enabled. bit 4: loss of signal clear interrupt mask (loscim) 0 = interrupt masked. 1 = interrupt enabled. bit 3: jitter attenuator limit trip set interrupt mask (jaltsim) 0 = interrupt masked. 1 = interrupt enabled. bit 2: open-circuit detect interrupt mask (ocdim) 0 = interrupt masked. 1 = interrupt enabled. bit 1: short-circuit detect interrupt mask (scdim) 0 = interrupt masked. 1 = interrupt enabled. bit 0 : loss of signal detect interrupt mask (losdim) 0 = interrupt masked. 1 = interrupt enabled.
DS26518 8-port t1/e1/j1 transceiver 233 of 286 register name: llsr register description: liu latched status register register address: 1005h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name jaltc occ scc losc jalts ocd scd losd default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can create interrupts. bit 7: jitter attenuator limit trip clear (jaltc). this latched bit is set when a ja limit trip condition was detected and then removed. bit 6: open-circuit clear (occ). this latched bit is set when an open circuit condition was detected at ttipn and tringn and then removed. bit 5: short-circuit clear (scc). this latched bit is set when a short circuit condition was detected at ttipn and tringn and then removed. bit 4: loss of signal clear (losc). this latched bit is set when a loss of signal condition was detected at rtipn and rringn and then removed. bit 3: jitter attenuator limit trip set (jalts). this latched bit is set when the jitter attenuator trip condition is detected. bit 2: open-circuit detect (ocd). this latched bit is set when open-circuit condition is detected at ttipn and tringn. this bit is not functional in t1 csu operating modes (t1 lbo 5, lbo 6, and lbo 7). bit 1: short-circuit detect (scd). this latched bit is set when short-circuit condition is detected at ttipn and tringn. this bit is not functional in t1 csu operating modes (t1 lbo 5, lbo 6, and lbo 7). bit 0: loss of signal detect (losd). this latched bit is set when an los condition is detected at rtipn and rringn.
DS26518 8-port t1/e1/j1 transceiver 234 of 286 register name: lrsl register description: liu receive signal level register register address: 1006h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rsl3 rsl2 rls1 rls0 ? ? ? ? default 0 0 0 0 0 0 0 0 bits 7 to 4: receiver signal level 3 to 0 (rsl[3:0]). real-time receive signal level as shown in table 10-18 . note that the range of signal levels r eported the rsl[3:0] is limited by the equal izer gain limit (egl) in short-haul applications. table 10-18. receive level indication rsl3 rsl2 rsl1 rsl0 receive level ds1/e1 (db) 0 0 0 0 > -2.5 0 0 0 1 -2.5 to -5 0 0 1 0 -5 to -7.5 0 0 1 1 -7.5 to -10 0 1 0 0 -10 to -12.5 0 1 0 1 -12.5 to -15 0 1 1 0 -15 to -17.5 0 1 1 1 -17.5 to -20 1 0 0 0 -20 to -22.5 1 0 0 1 -22.5 to 25 1 0 1 0 -25 to -27.5 1 0 1 1 -27.5 to -30 1 1 0 0 -30 to -32.5 1 1 0 1 -32.5 to -35 1 1 1 0 -35 to -37.5 1 1 1 1 < -37.5
DS26518 8-port t1/e1/j1 transceiver 235 of 286 register name: lrismr register description: liu receive impedance and sensitivity monitor register register address: 1007h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? rimpon ? ? ? rimpm2 rimpm1 rimpm0 default 0 0 0 0 0 0 0 0 bit 6: receive internal im pedance match on (rimpon) 0 = receive internal impedance termination is disabled (high impedance). 1 = receive internal impedance termination is enabled. bits 2 to 0: receive impedance selection (rimpm[2:0]). these bits are used to select the receive impedance termination. they must be set according to the cable impe dance even if internal termination resistance is disabled (rimpon = 0). see table 10-19 . table 10-19. receive impedance selection rimpon rimprm[2:0] receive impedance selected ( ) 0 x00 75 external termination (no internal impedance match) 0 x01 100 external termination (no internal impedance match) 0 x10 110 external termination (no internal impedance match) 0 x11 120 external termination (no internal impedance match) 1 000 75 , with external 120 resistor 1 001 100 , with external 120 resistor 1 010 110 , with external 120 resistor 1 011 120 , with external 120 resistor 1 100 75 internal termination 1 101 100 internal termination 1 110 110 internal termination 1 111 120 internal termination
DS26518 8-port t1/e1/j1 transceiver 236 of 286 register name: lrcr register description: liu receive control register register address: 1008h + (20h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rg703 ? ? ? rtr rmonen rsms1 rsms0 default 0 0 0 0 0 0 0 0 bit 7: receive g.703 clock (rg703). if this bit is set, the receiver expects a 2.048mhz or 1.544mhz clock from the rtipn/rringn, based on the selection of t1 (1.544) or e1 (2.048) mode in the ltrcr register. bit 3: receiver turns ratio (rtr) 0 = receive transformer turns ratio is 1:1. 1 = receive transformer turns ratio is 2:1. this opt ion should only be used in short-haul applications. note: internal impedance match is not available for this mode. bit 2: receiver monitor mode enable (rmonen) 0 = disable receive monitor mode. 1 = enable receive monitor mode. resistive gain is added with the maximum sensitivity. the receiver sensitivity is determined by rsms1 and rsms0. bits 1 and 0: receiver sensitivity/monitor gain select (rsms[1:0]). these bits are used to select the receiver sensitivity level and additional gain in monitoring applic ations. the monitor mode (rmonen) adds resistive gain to compensate for the signal loss caus ed by the isolation resistors. see table 10-20 and table 10-21 . table 10-20. receiver sensitivity sel ection with monitor mode disabled rmonen rsms[1:0] receiver monitor mode gain (db) receiver sensitivity (max cable loss allowed) (db) 0 00 0 12 0 01 0 20 0 10 0 30 0 11 0 36 for t1; 43 for e1 table 10-21. receiver sensitivity sel ection with monitor mode enabled rmonen rsms[1:0] receiver monitor mode gain (db) receiver sensitivity (max cable loss allowed) (db) 1 00 14 30 1 01 20 22.5 1 10 26 17.5 1 11 32 12
DS26518 8-port t1/e1/j1 transceiver 237 of 286 10.6 bert register definitions table 10-22. bert register set address name description r/w 1100h bawc bert alternating word count rate register r 1101h brp1 bert repetitive patte rn set register 1 r/w 1102h brp2 bert repetitive patte rn set register 2 r/w 1103h brp3 bert repetitive patte rn set register 3 r/w 1104h brp4 bert repetitive patte rn set register 4 r/w 1105h bc1 bert control register 1 r/w 1106h bc2 bert control register 2 r/w 1107h bbc1 bert bit count register 1 r 1108h bbc2 bert bit count register 2 r 1109h bbc3 bert bit count register 3 r 110ah bbc4 bert bit count register 4 r 110bh bec1 bert error count register 1 r 110ch bec2 bert error count register 2 r 110dh bec3 bert error count register 3 r 110eh blsr bert latched status register r 110fh bsim bert status interrupt mask register r/w register name: bawc register description: bert alternating word count rate register register address: 1100h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name acnt7 acnt6 acnt5 acnt 4 acnt3 acnt2 acnt1 acnt0 default 0 0 0 0 0 0 0 0 bits 7 to 0: alternating word count rate bits 7 to 0 (acnt[7:0]). when the bert is programmed in the alternating word mode, the words will repeat for the count l oaded into this register then flip to the other word and again repeat for the number of times loaded into this regist er. acnt0 is the lsb of the 8-bit alternating word count rate counter.
DS26518 8-port t1/e1/j1 transceiver 238 of 286 register name: brp1 register description: bert repetitive pattern set register 1 register address: 1101h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rpat7 rpat6 rpat5 rpat 4 rpat3 rpat2 rpat1 rpat0 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert repetitive pattern set bits 7 to 0 (rpat[7:0]). rpat0 is the lsb of the 32-bit repetitive pattern. register name: brp2 register description: bert repetitive pattern set register 2 register address: 1102h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rpat15 rpat14 rpat13 rpat 12 rpat11 rpat10 rpat9 rpat8 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert repetitive pattern set bits 15 to 8 (rpat[15:8]) register name: brp3 register description: bert repetitive pattern set register 3 register address: 1103h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rpat23 rpat22 rpat21 rpat 20 rpat19 rpat18 rpat17 rpat16 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert repetitive pattern set bits 23 to 16 (rpat[23:16]) register name: brp4 register description: bert repetitive pattern set register 4 register address: 1104h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name rpat31 rpat30 rpat29 rpat 28 rpat27 rpat26 rpat25 rpat24 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert repetitive pattern set bits 31 to 24 (rpat[31:24]). rpat31 is the msb of the 32-bit repetitive pattern.
DS26518 8-port t1/e1/j1 transceiver 239 of 286 register name: bc1 register description: bert control register 1 register address: 1105h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name tc tinv rinv ps2 ps1 ps0 lc resync default 0 0 0 0 0 0 0 0 bit 7: transmit pattern load (tc). a low-to-high transition loads the pattern generator with the pattern that is to be generated. this bit should be toggled from low to high whenever the host wishes to load a new pattern. must be cleared and set again for a subsequent loads. bit 6:transmit invert data enable (tinv) 0 = do not invert the outgoing data stream. 1 = invert the outgoing data stream. bit 5:receive invert data enable (rinv). 0 = do not invert the incoming data stream. 1 = invert the incoming data stream. bits 4 to 2: pattern select bits 2 to 0 (ps[2:0]). these bits select data pattern used by the transmit and receive circuits. see table 10-23 . table 10-23. bert pattern select ps2 ps1 ps0 pattern definition 0 0 0 pseudorandom 2e7?1. 0 0 1 pseudorandom 2e11?1. 0 1 0 pseudorandom 2e15?1. 0 1 1 pseudorandom pattern qrss. a 2 20 - 1 pattern with 14 consecutive zero restriction. 1 0 0 repetitive pattern. 1 0 1 alternating word pattern. 1 1 0 modified 55 octet (daly) pattern. the daly patte rn is a repeating 55 octet pattern that is byte-aligned into the active ds0 time slots. the pattern is defined in an atis (alliance for telecommunications industry solutions) committee t1 technical report number 25 (november 1993). 1 1 1 pseudorandom 2e-9-1. bit 1: load bit and error counters (lc). a low-to-high transition latches the current bit and error counts into the registers bbc1, bbc2, bbc3, bbc4 and bec1, bec2, bec3 and clears the internal count. this bit should be toggled from low to high whenever the host wishes to begin a new acquisition period. must be cleared and set again for a subsequent loads. bit 0: force resynchronization (resync). a low-to-high transition will force the receive bert synchronizer to resynchronize to the incoming data stream. this bit should be toggled from low to high whenever the host wishes to acquire synchronization on a new pattern. must be cleared and set again for a subsequent resynchronization.
DS26518 8-port t1/e1/j1 transceiver 240 of 286 register name: bc2 register description: bert control register 2 register address: 1106h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name eib2 eib1 eib0 sbe rpl3 rpl2 rpl1 rpl0 default 0 0 0 0 0 0 0 0 bits 7 to 5: error insert bits 2 to 0 (eib[2:0]). will automatically insert bit errors at the prescribed rate into the generated data pattern. can be used for verifying error detection features. see table 10-24 . table 10-24. bert error insertion rate eib2 eib1 eib0 error rate inserted 0 0 0 no errors automatically inserted 0 0 1 10e-1 0 1 0 10e-2 0 1 1 10e-3 1 0 0 10e-4 1 0 1 10e-5 1 1 0 10e-6 1 1 1 10e-7 bit 4: single bit error insert (sbe). a low-to-high transition will create a si ngle bit error. must be cleared and set again for a subsequent bit error to be inserted. bits 3 to 0: repetitive pattern length select 3 to 0 (rpl[3:0]). rpl0 is the lsb and rpl3 is the msb of a nibble that describes the how long the repetitive pattern is. the valid range is 17 (0000) to 32 (1111). these bits are ignored if the receive bert is programmed for a ps eudorandom pattern. to create repetitive patterns fewer than 17 bits in length, the user must set the length to an in teger number of the desired length that is less than or equal to 32. for example, to create a 6-bit pattern, the user can set the length to 18 (0001) or to 24 (0111) or to 30 (1101). see table 10-25 . table 10-25. bert repetitive pattern length select length (bits) rpl3 rpl2 rpl1 rpl0 17 0 0 0 0 18 0 0 0 1 19 0 0 1 0 20 0 0 1 1 21 0 1 0 0 22 0 1 0 1 23 0 1 1 0 24 0 1 1 1 25 1 0 0 0 26 1 0 0 1 27 1 0 1 0 28 1 0 1 1 29 1 1 0 0 30 1 1 0 1 31 1 1 1 0 32 1 1 1 1
DS26518 8-port t1/e1/j1 transceiver 241 of 286 register name: bbc1 register description: bert bit count register 1 register address: 1107h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name bbc7 bbc6 bbc5 bbc 4 bbc3 bbc2 bbc1 bbc0 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert bit counter bits 7 to 0 (bbc[7:0]). bbc0 is the lsb of the 32-bit counter. register name: bbc2 register description: bert bit count register 2 register address: 1108h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name bbc15 bbc14 bbc13 bbc 12 bbc11 bbc10 bbc9 bbc8 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert bit counter bits 15 to 8 (bbc[15:8]). register name: bbc3 register description: bert bit count register 3 register address: 1109h + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name bbc23 bbc22 bbc21 bbc 20 bbc19 bbc18 bbc17 bbc16 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert bit counter bits 23 to 16 (bbc[23:16]). register name: bbc4 register description: bert bit count register 4 register address: 110ah + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name bbc31 bbc30 bbc29 bbc 28 bbc27 bbc26 bbc25 bbc24 default 0 0 0 0 0 0 0 0 bits 7 to 0: bert bit counter bits 31 to 24 (bbc[31:24]). bbc31 is the msb of the 32-bit counter.
DS26518 8-port t1/e1/j1 transceiver 242 of 286 register name: bec1 register description: bert error count register 1 register address: 110bh + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ec7 ec6 ec5 ec4 ec3 ec2 ec1 ec0 default 0 0 0 0 0 0 0 0 bits 7 to 0: error counter bits 7 to 0 (ec[7:0]). ec0 is the lsb of the 24-bit counter. register name: bec2 register description: bert error count register 2 register address: 110ch + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ec15 ec14 ec13 ec12 ec11 ec10 ec9 ec8 default 0 0 0 0 0 0 0 0 bits 7 to 0: error counter bits 15 to 8 (ec[15:8]) register name: bec3 register description: bert error count register 3 register address: 110dh + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ec23 ec22 ec21 ec20 ec19 ec18 ec17 ec16 default 0 0 0 0 0 0 0 0 bits 7 to 0: error counter bits 23 to 16 (ec[23:16]). ec23 is the msb of the 24-bit counter.
DS26518 8-port t1/e1/j1 transceiver 243 of 286 register name: blsr register description: bert latched status register register address: 110eh + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? bbed bbco beco bra1 bra0 brlos bsync default 0 0 0 0 0 0 0 0 note: all bits in this register are latched and can create interrupts. bit 6: bert bit error detected event (bbed). a latched bit that is set when a bit error is detected. the receive bert must be in synchronization for it to detect bit errors. bit 5: bert bit counter overflow event (bbco). a latched bit that is set when the 32-bit bert bit counter (bbc) overflows. bit 4: bert error counter overflow event (beco). a latched bit that is set when the 24-bit bert error counter (bec) overflows. bit 3: bert receive all-ones condition (bra1). a latched bit that is set wh en 32 consecutive ones are received. bit 2: bert receive all-zeros condition (bra0). a latched bit that is set when 32 consecutive zeros are received. bit 1: bert receive loss of synchronization condition (brlos). a latched bit that is set whenever the receive bert begins searching for a pattern. bit 0: bert in synchronization condition (bsync). will be set when the incoming pattern matches for 32 consecutive bit positions.
DS26518 8-port t1/e1/j1 transceiver 244 of 286 register name: bsim register description: bert status interrupt mask register register address: 110fh + (10h x (n - 1)) : where n = 1 to 8 bit # 7 6 5 4 3 2 1 0 name ? bbed bbco beco bra1 bra0 brlos bsync default 0 0 0 0 0 0 0 0 bit 6: bert bit error detected event (bbed) 0 = interrupt masked. 1 = interrupt enabled. bit 5: bert bit counter overflow event (bbco) 0 = interrupt masked. 1 = interrupt enabled. bit 4: bert error counter overflow event (beco) 0 = interrupt masked. 1 = interrupt enabled. bit 3: bert receive al l ones condition (bra1) 0 = interrupt masked. 1 = interrupt enabled?interrupts on rising and falling edges. bit 2: bert receive all zeros condition (bra0) 0 = interrupt masked. 1 = interrupt enabled?interrupts on rising and falling edges. bit 1: bert receive loss of synchronization condition (brlos) 0 = interrupt masked. 1 = interrupt enabled?interrupts on rising and falling edges. bit 0: bert in synchronization condition (bsync) 0 = interrupt masked. 1 = interrupt enabled?interrupts on rising and falling edges.
DS26518 8-port t1/e1/j1 transceiver 245 of 286 11. functional timing 11.1 t1 receiver functional timing diagrams figure 11-1. t1 receive-side d4 timing frame# 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 rsyncn 3 rsyncn 1 rfsyncn rsyncn 2 note 1: rsyncn in the frame mode (riocr.0 = 0) a nd double-wide frame sync is not enabled (riocr.1 = 0). note 2: rsyncn in the frame mode (riocr.0 = 0) and double-wide frame sync is enabled (riocr.1 = 1). note 3: rsyncn in the multiframe mode (riocr.0 = 1). figure 11-2. t1 receive-side esf timing 1 2 3 4 5 6 7 8 9 10 11 12 rfsyncn frame# rsyncn 1 rsyncn 2 rsyncn 3 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 note 1: rsyncn in the frame mode (riocr.0 = 0) a nd double-wide frame sync is not enabled (riocr.1 = 0). note 2: rsyncn in the frame mode (riocr.0 = 0) and double-wide frame sync is enabled (riocr.1 = 1). note 3: rsyncn in the multiframe mode (riocr.0 = 1).
DS26518 8-port t1/e1/j1 transceiver 246 of 286 figure 11-3. t1 receive-side boundary timing (elastic store disabled) channel 23 channel 24 channel 1 channel 23 channel 24 channel 1 rclkn rsern rsyncn rfsyncn rsign rchclkn rchblkn 1 b a c/a d/b a c/a d/b lsb f msb msb lsb a b note 1: rchblkn is programmed to block channel 24. figure 11-4. t1 receive-side 1.544mhz b oundary timing (elastic store enabled) rsern channel 23 channel 24 channel 1 rchclkn rc hblk 3 rsysclkn rsyncn 2 rsyncn 1 rmsyncn rsign lsb f msb msb lsb channel 23 channel 24 channel 1 b a c/a d/b a c/a d/b a b note 1: rsyncn is in the output mode (riocr.2 = 0). note 2: rsyncn is in the input mode (riocr.2 = 1). note 3: rchblk is programmed to block channel 24.
DS26518 8-port t1/e1/j1 transceiver 247 of 286 figure 11-5. t1 receive-side 2.048mhz b oundary timing (elastic store enabled) rsern 1 channel 1 rchclkn rchblkn 4 rsysclkn rsyncn 3 channel 31 channel 32 rsyncn 2 rmsyncn rsign channel 31 channel 32 b a c/a d/b c/a d/b a b channel 1 lsb msb lsb note 1: rsern data in channels 1, 5, 9, 13, 17, 21, 25, and 29 are forced to one. note 2: rsyncn is in the output mode (riocr.2 = 0). note 3: rsyncn is in the input mode (riocr.2 = 1). note 4: rchblkn is programmed to block channel 1. note 5: the f-bit position is passed through the receive-side elastic store.
DS26518 8-port t1/e1/j1 transceiver 248 of 286 figure 11-6. t1 receive-side inte rleave bus operation?byte mode rsern lsb rsysclkn rsyncn 3 framer 3, channel 32 msb lsb framer 0, channel 1 rsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 1, channel 1 framer 1, channel 1 rsern 1 rsyncn rsign 1 rsern 2 rsign 2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 bit detail fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 a b c d a b c d a b c d note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: rsyncn is in the input mode (riocr.2 = 0). note 4: though not shown, rchclkn continues to mark the channel lsb for the framer's active period. note 5: though not shown, rchblkn continues to mark the blocked channels for the framer?s active period.
DS26518 8-port t1/e1/j1 transceiver 249 of 286 figure 11-7. t1 receive-side inte rleave bus operation?frame mode fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 rsern lsb rsysclkn rsyncn framer 3, channel 32 msb lsb framer 0, channel 1 rsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 0, channel 2 framer 0, channel 2 rsern 1 rsyncn rsign 1 rsern 2 rsign 2 bit detail a b c/a d/b a b c/a d/b a b c/a d/b fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: rsyncn is in the input mode (riocr.2 = 0). note 4: though not shown, rchclkn continues to mark the channel lsb for the framer's active period. note 5: though not shown, rchblkn continues to mark the blocked channels for the framer?s active period. figure 11-8. t1 receive-side rchclkn gapped mode during f-bit rclkn rchclkn rsyncn rsern lsb f-bit msb
DS26518 8-port t1/e1/j1 transceiver 250 of 286 11.2 t1 transmitter functional timing diagrams figure 11-9. t1 transm it-side d4 timing 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 tssyncion frame# tsyncn 1 tsyncn 2 tsyncn 3 note 1: tsyncn in the frame mode (tiocr.0 = 0) a nd double-wide frame sync is not enabled (tiocr.1 = 0). note 2: tsyncn in the frame mode (tiocr.0 = 0) and double-wide frame sync is enabled (tiocr.1 = 1). note 3: tsyncn in the multiframe mode (tiocr.0 = 1). figure 11-10. t1 transmit-side esf timing 1 2 3 4 5 6 7 8 9 10 11 12 tssyncion frame# tsyncn 1 tsyncn 2 tsyncn 3 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 note 1: tsyncn in the frame mode (tiocr.0 = 0) a nd double-wide frame sync is not enabled (tiocr.1 = 0). note 2: tsyncn in the frame mode (tiocr.0 = 0) and double-wide frame sync is enabled (tiocr.1 = 1). note 3: tsyncn in the multiframe mode (tiocr.0 = 1).
DS26518 8-port t1/e1/j1 transceiver 251 of 286 figure 11-11. t1 transmit-side boundary timing (elastic store disabled) lsb f msb lsb msb lsb msb channel 1 channel 2 channel 1 channel 2 a b c/a d/b a b c/a d/b tclkn tsern tsyncn 1 tsyncn 2 tsign tchclkn tchblkn 3 d/b note 1: tsyncn is in the output mode (tiocr.2 = 1). note 2: tsyncn is in the input mode (tiocr.2 = 0). note 3: tchblkn is programmed to block channel 2. figure 11-12. t1 transmit-side 1.544mhz b oundary timing (elastic store enabled) lsb f msb lsb msb channel 1 channel 24 a b c/a d/b a b c/a d/b tsysclkn tsern tssyncion tsign tchclkn tchblkn 1 channel 23 a channel 23 channel 24 channel 1 note 1: tchblkn is programmed to block channel 24.
DS26518 8-port t1/e1/j1 transceiver 252 of 286 figure 11-13. t1 transmit-side 2.048mhz boundary timing (elastic store enabled) lsb f 3 lsb msb channel 1 channel 32 a b c/a d/b a b c/a d/b tsysclkn tsern 1 tssyncion tsign tchclkn tchblkn 2 channel 31 a channel 31 channel 32 channel 1 note 1: tsern data in channels 1, 5, 9, 13, 17, 21, 25, and 29 is ignored. note 2: tchblkn is programmed to block channels 31 and 1. note 3: the f-bit position for the t1 frame is sampled and passed through the transmit-side elastic store into the msb bit position of cha nnel 1. (normally the transmit-side formatter overwrites the f-bit position unless the forma tter is programmed to pass through the f-bit position).
DS26518 8-port t1/e1/j1 transceiver 253 of 286 figure 11-14. t1 transmit-side inte rleave bus operation?byte mode tsern lsb tsysclkn tssyncion 3 framer 3, channel 32 msb lsb framer 0, channel 1 tsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 1, channel 1 framer 1, channel 1 tsern 1 tssyncion tsign 1 tsern 2 tsign 2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 bit detail fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 a b c/a d/b a b c/a d/b a b c/a d/b note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: tssyncion is in the input mode (tiocr.2 = 0). note 4: though not shown, tchclkn continues to mark the channel lsb for the framer's active period. note 5: though not shown, tchblkn continues to ma rk the blocked channels for the framer?s active period.
DS26518 8-port t1/e1/j1 transceiver 254 of 286 figure 11-15. t1 transmit-side inte rleave bus operation?frame mode fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 tsern lsb tsysclkn tssyncion 3 framer 3, channel 32 msb lsb framer 0, channel 1 tsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 0, channel 2 framer 0, channel 2 tsern 1 tssyncion tsign 1 tsern 2 tsign 2 bit detail a b c/a d/b a b c/a d/b a b c/a d/b fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: tssyncion is in the input mode (tiocr.2 = 0). note 4: though not shown, tchclkn continues to mark the channel lsb for the framer's active period. note 5: though not shown, tchblkn continues to ma rk the blocked channels for the framer?s active period. figure 11-16. t1 transmit-side t chclkn gapped mode during f-bit tclkn tchclkn tsyncn tsern lsb msb
DS26518 8-port t1/e1/j1 transceiver 255 of 286 11.3 e1 receiver functional timing diagrams figure 11-17. e1 receive-side timing frame# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 rsyncn 2 rsyncn 1 rfsyncn note 1: rsyncn in frame mode (riocr.0 = 0). note 2: rsyncn in multiframe mode (riocr.0 = 1). note 3: this diagram assumes the cas mf begins in the raf frame. figure 11-18. e1 receive-side boundary timing (elastic store disabled) channel 32 channel 1 channel 2 channel 32 channel 1 channel 2 rclkn rsern rsyncn rfsyncn rsign rchclkn 1 rchblkn 1 c d a lsb msb a b si 1 a sa4 sa5 sa6 sa7 sa8 b note 3 note 1: rchblkn is programmed to block channel 1. note 2: shown is an rnaf frame boundary. note 3. rsign normally contains the cas mu ltiframe alignment nibble (0000) in channel 1.
DS26518 8-port t1/e1/j1 transceiver 256 of 286 figure 11-19. e1 receive-side 1.544mhz b oundary timing (elastic store enabled) rsern 1 channel 23/31 channel 24/32 channel 1/2 rchclkn rchblkn 4 rsysclkn rsyncn 3 rsyncn 2 rmsyncn lsb f msb msb lsb note 1: data from the e1 channels 1, 5, 9, 13, 17, 21, 25, and 29 is dropped (channel 2 from the e1 link is mapped to channel 1 of the t1 link, etc.) and the f-bit position is added (forced to one). note 2: rsyncn in the output mode (riocr.2 = 0). note 3: rsyncn in the input mode (riocr.2 = 1). note 4: rchblkn is programmed to block channel 24. figure 11-20. e1 receive-side 2.048mhz boundary timing (elastic store enabled) rsern channel 1 rchclkn rchblkn 3 rsysclkn rsyncn 2 channel 31 channel 32 rsyncn 1 rmsyncn rsign channel 31 channel 32 c d a b channel 1 lsb msb lsb msb c d b a note 4 note 1: rsyncn in the output mode (riocr.2 = 0). note 2: rsyncn in the input mode (riocr.2 = 1). note 3: rchblkn is programmed to block channel 1. note 4: rsign normally contains the cas mu ltiframe alignment nibble (0000) in channel 1.
DS26518 8-port t1/e1/j1 transceiver 257 of 286 figure 11-21. e1 receive-side in terleave bus operation?byte mode rsern lsb rsysclkn rsyncn 3 framer 3, channel 32 msb lsb framer 0, channel 1 rsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 1, channel 1 framer 1, channel 1 rsern 1 rsyncn rsign 1 rsern 2 rsign 2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 bit detail fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 a b c d a b c d a b c d note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: rsyncn is in the input mode (riocr.2 = 0). note 4: though not shown, rchclkn continues to mark the channel lsb for the framer's active period. note 5: though not shown, rchblkn continues to mark the blocked channels for the framer?s active period.
DS26518 8-port t1/e1/j1 transceiver 258 of 286 figure 11-22. e1 receive-side interleave bus operation?frame mode fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 rsern lsb rsysclkn rsyncn 3 framer 3, channel 32 msb lsb framer 0, channel 1 rsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 0, channel 2 framer 0, channel 2 rsern 1 rsyncn rsign 1 rsern 2 rsign 2 bit detail a b c/a d/b a b c/a d/b a b c/a d/b fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: rsync is in the input mode (riocr.2 = 0). note 4: though not shown, rchclk continues to ma rk the channel lsb for the framer's active period. note 5: though not shown, rchblk continues to mark the blocked channels for the framer?s active period. figure 11-23. e1 receive-side rchcl kn gapped mode during channel 1 rclkn rsyncn rchclkn rsern lsb f f f f f f f f msb
DS26518 8-port t1/e1/j1 transceiver 259 of 286 11.4 e1 transmitter functional timing diagrams figure 11-24. e1 transmit-side timing 1 2 3 4 5 6 7 8 9 10 11 12 tssyncion frame# tsyncn 1 tsyncn 2 13 14 15 16 1 2 3 4 5 14 15 16 6 7 8 9 10 note 1: tsyncn in frame mode (tiocr.0 = 0). note 2: tsyncn in multiframe mode (tiocr.0 = 1). note 3: this diagram assumes both the cas mf and the crc-4 mf begin with the taf frame. figure 11-25. e1 transmit-side boundary timing (elastic store disabled) lsb msb lsb msb channel 1 channel 2 channel 1 channel 2 a b c d tclkn tsern tsyncn 1 tsyncn 2 tsign tchclkn tchblkn 3 si 1 a sa4 sa5 sa6 sa7 sa8 d note 1: tsyncn in the output mode (tiocr.2 = 1). note 2: tsyncn in the input mode (tiocr.2 = 0). note 3: tchblkn is programmed to block channel 2. note 4: the signaling data at tsign during channe l 1 is normally overwritten in the transmit formatter with the cas mf alignment nibble (0000). note 5: shown is a tnaf frame boundary.
DS26518 8-port t1/e1/j1 transceiver 260 of 286 figure 11-26. e1 transmit-side 1.544mhz boundary timing (elastic store enabled) lsb f msb lsb msb channel 1 channel 24 tsysclkn tsern 1 tssyncion tchclkn tchblkn 2 channel 23 note 1: the f-bit position in the tsern data is ignored. note 2: tchblkn is programmed to block channel 24. figure 11-27. e1 transmit-side 2.048mhz b oundary timing (elastic store enabled) tsern channel 1 tchclkn tchblkn 2 tsysclkn tsyncn 1 channel 31 channel 32 tsign channel 31 channel 32 c d a b channel 1 lsb msb lsb msb c d b a note 1: tsyncn in the input mode (tiocr.2 = 0). note 2: tchblkn is programmed to block channel 1.
DS26518 8-port t1/e1/j1 transceiver 261 of 286 figure 11-28. e1 transmit-side inte rleave bus operation?byte mode tsern lsb tsysclkn tssyncion 3 framer 3, channel 32 msb lsb framer 0, channel 1 tsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 1, channel 1 framer 1, channel 1 tsern 1 tssyncion tsign 1 tsern 2 tsign 2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 bit detail fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr1 ch32 fr0 ch1 fr1 ch1 fr0 ch2 fr1 ch2 fr2 ch32 fr3 ch32 fr0 ch1 fr1 ch1 fr2 ch1 fr3 ch1 fr0 ch2 fr1 ch2 fr2 ch2 fr3 ch2 a b c/a d/b a b c/a d/b a b c/a d/b note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: tssyncion is in the input mode (tiocr.2 = 0). note 4: though not shown, tchclkn continues to mark the channel lsb for the framer's active period. note 5: though not shown, tchblkn continues to ma rk the blocked channels for the framer?s active period.
DS26518 8-port t1/e1/j1 transceiver 262 of 286 figure 11-29. e1 transmit-side inte rleave bus operation?frame mode fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 tsern lsb tsysclkn tssyncion 3 framer 3, channel 32 msb lsb framer 0, channel 1 tsign framer 3, channel 32 framer 0, channel 1 msb lsb framer 0, channel 2 framer 0, channel 2 tsern 1 tssyncion tsign 1 tsern 2 tsign 2 bit detail a b c/a d/b a b c/a d/b a b c/a d/b fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 fr0 ch1-32 fr1 ch1-32 fr2 ch1-32 fr3 ch1-32 note 1: 4.096mhz bus configuration. note 2: 8.192mhz bus configuration. note 3: tssyncion is in the input mode (tiocr.2 = 0). note 4: though not shown, tchclkn continues to mark the channel lsb for the framer's active period. note 5: though not shown, tchblkn continues to ma rk the blocked channels for the framer?s active period.
DS26518 8-port t1/e1/j1 transceiver 263 of 286 figure 11-30. e1 g.802 timing 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1718 19 20 21 22 23 24 25 2627 28 29 30 31 0 31 32 ts# rsyncn tsyncn rchclkn tchclkn rchblkn tchblkn channel 26 channel 25 lsb msb rclkn/rsysclkn tclkn/tsysclkn rsern/tsern rchclkn/tchclkn rchblkn/tchblkn 1 2 0 note: rchblkn or tchblkn programmed to pul se high during time slots 1 through 15, 17 through 25, and bit 1 of time slot 26. figure 11-31. e1 transmit-side tchclkn gapped mode during channel 1 tclkn tsyncn tchclkn tsern lsb msb
DS26518 8-port t1/e1/j1 transceiver 264 of 286 12. operating parameters absolute maximum ratings voltage range on any lead with respect to v ss (except v dd )?????????????????.-0.3v to +5.5v supply voltage (v dd ) range with respect to v ss ??????????????????????..-0.3v to +3.63v operating temperature range commercial (DS26518g)??????????????????????????????0 c to +70 c industrial (DS26518gn)????????????? ????????????????...-40c to +85c storage temperature range...??????????????????????????????-55c to +125c soldering temperature??????????????????????.s ee ipc/jedec j-std-020 specification this is a stress rating only and functional oper ation of the device at these or any ot her conditions above t hose indicated in t he operation sections of this specification is not implied. exposure to absolute maximum rating co nditions for extended periods of time may affect reliability. table 12-1. recommended dc operating conditions (t a = -40c to +85 c for DS26518gn.) parameter symbol conditions min typ max units logic 1 v ih 2.0 5.5 v logic 0 v il -0.3 +0.8 v i/o supply v dd 3.135 3.3 3.465 v core supply v dd-core 1.71 1.8 1.89 v table 12-2. capacitance (t a = +25c) parameter symbol conditions min typ max units input capacitance c in 7 pf output capacitance c out 7 pf table 12-3. recommended dc operating conditions (v dd = 3.135v to 3.465v, t a = -40c to +85 c for DS26518gn.) parameter symbol conditions min typ max units 3.3v supply current i dd (notes 1, 2) 300 450 ma 1.8v core supply current i dd-core (notes 1, 2) 75 100 ma input leakage i il -10.0 +10.0 a pullup pin input leakage i ilp (note 3) -85.0 +10.0 a pulldown pin input leakage i ilp (note 3) -10.0 +85.0 a tri-state output leakage i ol -10.0 +10.0 a output voltage (i oh = -4ma) v oh 2.4 v output voltage (i ol = +4ma) v ol 0.4 v note 1: rclk1-n = tclk1-n = 2.048mhz, digital outputs without load. note 2: max power consumed is measured with all ports transmitti ng an all-ones data pattern with a transmitter load of 100 . note 3: pullup/pulldown pins include spi_sel, tsysclk[2:8], rsysclk[2:8], digioen, jtrst , jtms, and jtdi.
DS26518 8-port t1/e1/j1 transceiver 265 of 286 12.1 thermal characteristics table 12-4. thermal characteristics parameter conditions min typ max units ambient temperature (note 1) -40 +85 c junction temperature +125 c theta-ja ( ja ) in still air for 256-pin te-csbga (note 2) +17.5 c/w note 1: the package is mounted on a four-layer jedec standard test board. note 2: theta-ja ( ja ) is the junction-to-ambient thermal resistance, when t he package is mounted on a four-layer jedec standard test board. 12.2 line interface characteristics table 12-5. transmitter characteristics parameter symbol conditions min typ max units e1 75 2.13 2.37 2.61 e1 120 2.70 3.00 3.30 t1 100 2.40 3.00 3.60 output mark amplitude v m j1 110 2.40 3.00 3.60 v output zero amplitude v s (note 1) -0.3 +0.3 v transmit amplitude variation with supply -1 +1 % table 12-6. receiver characteristics parameter symbol conditions min typ max units cable attenuation attn 43 db 192 192 allowable zeros before loss (note 1) 2048 24 192 allowable ones before loss (note 2) 192 note 1: 192 zeros for t1 and t1.231 specification compliance. 192 zeros for e1 and g.775 specification compliance. 2048 zeros for ets 300 233 compliance. note 2: 24 ones in 192-bit period for t1.231; 192 ones for g.775; 192 ones for ets 300 233.
DS26518 8-port t1/e1/j1 transceiver 266 of 286 13. ac timing characteristics unless otherwise noted, all timing numbers assume 20pf test load on output signals, 40pf test load on bus signals. 13.1 microprocessor bus ac characteristics 13.1.1 spi bus mode table 13-1. spi bus mode timing (see figure 13-1 .) symbol (note 1) characteristic (note 2) symbol min max units operating frequency slave f bus(s) 5 mhz t1 cycle time: slave t cyc(s) 200 ns t2 enable lead time t lead(s) 15 ns t3 enable lag time t lag(s) 15 ns t4, t5 clock (clk) duty cycle slave (t4/t1 or t5/t1) t clkh(s) 80 ns t6 data setup time (inputs) slave t su(s) 5 ns t7 data hold time (inputs) slave t h(s) 15 ns t8 disable time, slave (note 3) t dis(s) 25 ns t9 data valid time, after enable edge slave (note 4) t v(s) 40 ns t10 data hold time, outputs, after enable edge slave t hd(s) 5 ns note 1: symbols refer to dimensions in figure 13-1 . note 2: 100pf load on all spi pins. note 3: hold time to high-impedance state. note 4: with 100pf on all spi pins.
DS26518 8-port t1/e1/j1 transceiver 267 of 286 figure 13-1. spi interface timing diagram note 1: clock edge reference to data contro lled by cpha and cpol settings. see the functional timing diagrams. note 2: not defined, but usually msb of character just received. c sb input spi_sclk spi_sclk 1 mosi input miso output msb bits 13:0 slave msb bits 6:1 note 2 bit 14 t1 t4 t5 t2 t3 slave lsb t8 t6 t7 t9 t10
DS26518 8-port t1/e1/j1 transceiver 268 of 286 table 13-2. ac characteristics ?microprocessor bus timing (v dd = 3.3v 5%, t a = 0c to +70c for DS26518g; v dd = 3.3v 5%, t a = -40c to +85c for DS26518gn.) (see figure 13-2 , figure 13-3 , figure 13-4 , and figure 13-5 .) parameter symbol conditions min typ max units setup time for a[12:0] valid to csb active t1 0 ns setup time for csb active to either rdb , or wrb active t2 0 ns delay time from either rdb or dsb active to d[7:0] valid t3 (note 1) 175 ns hold time from either rdb or wrb inactive to csb inactive t4 0 ns hold time from csb or rdb or dsb inactive to d[7:0] tri-state t5 5 20 ns wait time from wrb active to latch data t6 40 ns data setup time to wrb inactive t7 10 ns data hold time from wrb inactive t8 2 ns address hold from wrb inactive t9 0 ns write access to subsequent write/read access delay time t10 (note 1) 30 ns note 1: if supplying a 1.544mhz mclk, the freqsel bit must be set to meet this timing.
DS26518 8-port t1/e1/j1 transceiver 269 of 286 figure 13-2. intel bus read timing (bts = 0) t2 t3 a ddress valid data valid t4 t9 t5 t10 a [12:0] d[7:0] c s b r d b w r b t1 figure 13-3. intel bus write timing (bts = 0) t2 t6 a ddress valid t4 t9 t10 a [12:0] d[7:0] c s b r d b w r b t7 t8 t1
DS26518 8-port t1/e1/j1 transceiver 270 of 286 figure 13-4. motorola bus read timing (bts = 1) t2 t6 a ddress valid t4 t9 t10 a [12:0] d[7:0] c s b r w b d s b t7 t8 t1 t9 a ddress valid data valid a [12:0] d[7:0] t5 r w b t1 c s b t2 figure 13-5 motorola bus write timing (bts = 1) t3 t4 t10 d s b
DS26518 8-port t1/e1/j1 transceiver 271 of 286 table 13-3. receiver ac characteristics (v dd = 3.3v 5%, t a = 0c to +70c for DS26518g; t a = -40c to +85c for DS26518gn.) (see figure 13-6 , figure 13-7 , and figure 13-8 .) parameter symbol conditions min typ max units (note 1) 648 rclkn period t cp (note 2) 488 ns t ch 125 rclkn pulse width t cl 125 ns (note 3) 60 rsysclkn period t sp (note 4) 60 ns t sh 30 rsysclkn pulse width t sl 30 ns rsyncn setup to rsysclkn falling t su 10 ns rsyncn pulse width t pw 50 ns delay rclkn to rser n, rsign valid t d1 10 ns delay rclkn to rchclkn, rsyncn, rchblkn, rfsyncn t d2 20 ns delay rsysclkn to rsern, rsign valid t d3 20 ns delay rsysclkn to rchclkn, rchblkn, rmsyncn, rsyncn t d4 20 ns note 1: t1 mode. note 2: e1 mode. note 3: rsysclkn = 1.544mhz. note 4: rsysclkn = 2.048mhz.
DS26518 8-port t1/e1/j1 transceiver 272 of 286 figure 13-6. receive framer timing?backplane (t1 mode) t d1 t d2 rsern/rsign rchclkn rchblkn rsyncn 1 rclkn rfsyncn/rmsyncn f-bit t d2 t d2 t d2 note 1: rsyncn is in the output mode. note 2: no relationship between rchclkn and rchblkn and other signals is implied.
DS26518 8-port t1/e1/j1 transceiver 273 of 286 figure 13-7. receive-side timing?el astic store enabled (t1 mode) note 1: rsyncn is in the output mode. note 2: rsyncn is in the input mode. note 3: f-bit when riocr.4 = 0, msb of ts0 when riocr.4 = 1. t d3 t d4 t d4 t d4 t t su hd rsern/rsign rchclkn rchblkn rsyncn 1 rsyncn 2 rsysclkn sl t t sp sh t t d4 rmsyncn see note 3 figure 13-8. receive fram er timing?line side rtipn , rrin g n rclkn cl t t cp ch t t su t hd
DS26518 8-port t1/e1/j1 transceiver 274 of 286 table 13-4. transmit ac characteristics (v dd = 3.3v 5%, t a = 0c to +70c for DS26518g; t a = -40c to +85c for DS26518gn.) (see figure 13-9 , figure 13-10 , and figure 13-11 .) parameter symbol conditions min typ max units (note 1) 648 tclkn period t cp (note 2) 488 ns t ch 125 tclkn pulse width t cl 125 ns (note 3) 60 tsysclkn period t sp (note 4) 60 ns t sh 30 tsysclkn pulse width t sl 30 ns tsyncn or tssyncion setup to tclkn or tsysclkn falling t su 10 ns tsyncn or tssyncion pulse width t pw (note 5) 50 ns 488 244 122 tssyncion pulse width (notes 6, 7) t pw 61 ns tsern, tsign setup to tclkn, tsysclkn falling t su 10 ns tsern, tsign hold from tclkn, tsysclkn falling t hd 10 ns delay tclkn to tchblkn, tchclkn, tsyncn t d2 20 ns delay tsysclkn to tchclkn, tchblkn t d3 20 ns delay bpclk1 to tssyncion (note 6) t d5 5 ns note 1: t1 mode. note 2: e1 mode. note 3: rsysclkn = 1.544mhz. note 4: rsysclkn = 2.048mhz. note 5: tssyncion configured as an input ( gtcr3 .1 = 0). note 6: tssyncion configured as an output ( gtcr3 .1 = 1). note 7: varies depending on the frequency of bpclk1.
DS26518 8-port t1/e1/j1 transceiver 275 of 286 figure 13-9. transmit formatter timing?backplane tclkn tsern/tsign tchclkn t t cl t ch cp tsyncn 1 tsyncn 2 tchblkn t d2 t d2 t d2 t t t su hd d1 t hd teso t su note 1: tsyncn is in the output mode. note 2: tsyncn is in the input mode. note 3: tsern is sampled on the falling edge of tc lk when the transmit-side elastic store is disabled. note 4: tchclkn and tchblkn are synchronous with tclk when the transmit-side elastic store is disabled. note 5: no relationship between tchclkn a nd tchblkn and the other signals is implied.
DS26518 8-port t1/e1/j1 transceiver 276 of 286 figure 13-10. transmit formatter timing?elastic store enabled tsysclkn tsern tchclkn t t sl t sh sp tssyncion tchblkn t d3 t d3 t t t su hd su t hd note 1: tsern is only sampled on the falling edge of tsysclkn when the transmit-side elastic store is enabled. note 2: tchclkn and tchblkn are synchronous with tsysc lkn when the transmit-side elastic store is enabled. figure 13-11. bpclk1 timing bpclk1 tssyncion 1 t d5 note 1: tssyncion is configured as an output (gtcr3.tssynciosel = 1).
DS26518 8-port t1/e1/j1 transceiver 277 of 286 13.2 jtag interface timing table 13-5. jtag interface timing (v dd = 3.3v 5%, t a = 0c to +70c for DS26518g; t a = -40c to +85c for DS26518gn.) (see figure 13-12 .) parameter symbol conditions min typ max units jtclk clock period t1 1000 ns jtclk clock high:low time t2:t3 (note 1) 50 500 ns jtclk to jtdi, jtms setup time t4 5 ns jtclk to jtdi, jtms hold time t5 2 ns jtclk to jtdo delay t6 2 50 ns jtclk to jtdo high-impedance delay t7 2 50 ns jtrst width low time t8 100 ns clock can be stopped high or low. note 1: figure 13-12. jtag interface timing diagram jtcl k t1 jtd0 t4 t5 t2 t3 t7 jtdi, jtms, j trs t t6 jtr s t t8
DS26518 8-port t1/e1/j1 transceiver 278 of 286 14. jtag boundary scan and test access port the DS26518 ieee 1149.1 design supports the standa rd instruction codes sample:preload, bypass, and extest. optional public instructions included are highz, clamp, and idcode. see table 14-1 . the DS26518 contains the following as required by ieee 1149.1 standard test access po rt and boundary scan architecture. test access port (tap) bypass register tap controller boundary scan register instruction register device identification register the test access port has t he necessary interface pins: jtrst , jtclk, jtms, jtdi, and jtdo. see the pin descriptions for details. figure 14-1. jtag func tional block diagram jtdi jtms jtclk j trst jtdo test access port controller v dd v dd v dd boundry scan register bypass register instruction register identification register mux select output enable 10k 10k 10k
DS26518 8-port t1/e1/j1 transceiver 279 of 286 14.1 tap controller state machine the tap controller is a finite state machine that responds to the logic level at jtms on the rising edge of jtclk. see figure 14-2 . 14.1.1 test-logic-reset upon power-up, the tap contro ller will be in the test-logic -reset state. the instructio n register will contain the idcode instruction. all system logi c of the device will operate normally. 14.1.2 run-test-idle the run-test-idle is used between scan operations or during specific test s. the instruction register and test registers will remain idle. 14.1.3 select-dr-scan all test registers retain their previous state. with jtms low, a rising edge of jtclk moves the controller into the capture-dr state and will initiate a scan sequence. jtms high during a rising edge on jtclk moves the controller to the select-ir-scan state. 14.1.4 capture-dr data may be parallel-loaded into the test data registers sele cted by the current instructi on. if the instruction does not call for a parallel load or the selected register does no t allow parallel loads, the test register remains at its current value. on the rising edge of jtclk, the controller goes to the shift-dr state if jtms is low or it goes to the exit1-dr state if jtms is high. 14.1.5 shift-dr the test data register selected by the current instruction is connected betwe en jtdi and jtdo and will shift data one stage towards its serial output on each rising edge of jtclk. if a test register selected by the current instruction is not placed in the serial path, it maintains it s previous state. 14.1.6 exit1-dr while in this state, a rising edge on jtclk puts the cont roller in the update-dr st ate, which terminates the scanning process if jtms is high. a rising edge on jtcl k with jtms low puts the controller in the pause-dr state. 14.1.7 pause-dr shifting of the test registers is halted while in this state. all test registers selected by the current instruction retain their previous state. the c ontroller remains in this state while jtms is low. a rising edge on jtclk with jtms high puts the controller in the exit2-dr state. 14.1.8 exit2-dr a rising edge on jtclk with jtms high while in this state puts the controller in the update-dr state and terminates the scanning process. a rising edge on jtclk with jtms low enters the shift-dr state. 14.1.9 update-dr a falling edge on jtclk while in the update-dr state latc hes the data from the shift register path of the test registers into the data output latches. this prevents changes at the paralle l output due to changes in the shift register. 14.1.10 select-ir-scan all test registers retain their previous state. the inst ruction register remains unchanged during this state. with jtms low, a rising edge on jtclk moves the controller in to the capture-ir state and initiates a scan sequence
DS26518 8-port t1/e1/j1 transceiver 280 of 286 for the instruction register. jtms high during a rising edge on jtclk puts the controller back into the test-logic- reset state. 14.1.11 capture-ir the capture-ir state is used to load the shift register in t he instruction register with a fixed value. this value is loaded on the rising edge of jtclk. if jtms is high on t he rising edge of jtclk, t he controller enters the exit1- ir state. if jtms is low on the rising edge of jtclk, the controller enter s the shift-ir state. 14.1.12 shift-ir in this state, the shift register in the instruction regi ster is connected between jtdi and jtdo and shifts data one stage for every rising edge of jtclk towards the serial outpu t. the parallel register, as well as all test registers, remains at their previous states. a rising edge on jtclk with jtms high moves the controller to the exit1-ir state. a rising edge on jtclk with jtms low keeps the controller in the shift-ir state while moving data one stage through the instruction shift register. 14.1.13 exit1-ir a rising edge on jtclk with jtms low puts the controller in the pause-ir state. if jtms is high on the rising edge of jtclk, the controller enters the update -ir state and terminates the scanning process. 14.1.14 pause-ir shifting of the instruction shift register is halted temporarily. with jtms high, a rising edge on jtclk puts the controller in the exit2-ir state. the controller remains in the pause-ir state if jtms is low during a rising edge on jtclk. 14.1.15 exit2-ir a rising edge on jtclk with jtms low puts the controller in the update-ir state. the controller loops back to shift-ir if jtms is high during a rising edge of jtclk in this state. 14.1.16 update-ir the instruction code shifted into the instruction shift regi ster is latched into the parallel output on the falling edge of jtclk as the controller enters this state. once latched, this instruction becomes the current instruction. a rising edge on jtclk with jtms low puts the controller in the run-test-idle state. with jtms high, the controller enters the select-dr-scan state.
DS26518 8-port t1/e1/j1 transceiver 281 of 286 figure 14-2. tap controller state diagram 1 0 0 1 11 1 1 1 1 1 11 1 1 00 0 0 0 1 0 0 0 0 1 1 0 0 0 0 select dr-scan capture dr shift dr exit dr pause dr exit2 dr update dr select ir-scan capture ir shift ir exit ir pause ir exit2 ir update ir test logic reset run test/ idle 0
DS26518 8-port t1/e1/j1 transceiver 282 of 286 14.2 instruction register the instruction register contains a shift register as well as a latched parallel output and is 3 bits in length. when the tap controller enters the shift-ir state, the instruction sh ift register is connected between jtdi and jtdo. while in the shift-ir state, a rising edge on jtclk with jtms low shifts the data one stage towards the serial output at jtdo. a rising edge on jtclk in the exit1-ir state or th e exit2-ir state with jtms high moves the controller to the update-ir state. the falli ng edge of that same jtclk will latch the data in the instruction shift register to the instruction parallel output. instructio ns supported by the DS26518 and its respec tive operational binary codes are shown in table 14-1 . table 14-1. instruction codes for ieee 1149.1 architecture instruction selected regi ster instruction codes sample:preload boundary scan 010 bypass bypass 111 extest boundary scan 000 clamp bypass 011 highz bypass 100 idcode device identification 001 14.2.1 sample:preload this is a mandatory instruction for the ieee 1149.1 specification. this instruction supports two functions. the digital i/os of the device can be sampled at the boundary scan register without interfering with the normal operation of the device by usin g the capture-dr state. sample:preload also allows the device to shift data into the boundary scan register via jtdi using the shift-dr state. 14.2.2 bypass when the bypass instruction is latched in to the parallel instructio n register, jtdi connec ts to jtdo through the one-bit bypass test register. this allows data to pass from jtdi to jtdo without a ffecting the device?s normal operation. 14.2.3 extest this allows testing of all interconnections to the device. when the extest instruction is latched in the instruction register, the following actions occur. once enabled via the update-ir state, the parallel outputs of all digital output pins will be driven. the boundary scan register will be c onnected between jtdi and jtdo. the capture-dr will sample all digital inputs into the boundary scan register. 14.2.4 clamp all digital outputs of the device will output data from the boundary scan parallel output while connecting the bypass register between jtdi and jtdo. the outputs w ill not change during the clamp instruction. 14.2.5 highz all digital outputs of the device will be placed in a hi gh-impedance state. the bypass register will be connected between jtdi and jtdo. 14.2.6 idcode when the idcode instruction is latched into the parallel instruction register, the iden tification test register is selected. the device identification code will be loaded into the identification register on the rising edge of jtclk following entry into the capture-dr stat e. shift-dr can be used to shift the identification code out serially via jtdo. during test-logic-reset, the identification code is forc ed into the instruction register?s parallel output. the id code will always have a ?1? in the lsb position. the next 11 bits identify the manufacturer?s jedec number and number of continuation bytes followed by 16 bits for the device and 4 bits for the version.
DS26518 8-port t1/e1/j1 transceiver 283 of 286 14.3 jtag id codes table 14-2. id code structure device revision id[31:28] device code id[27:12] manufacturer?s code id[11:1] required id[0] ds26519 consult factory 0000000010001011 00010100001 1 DS26518 consult factory 0000000010001010 00010100001 1 14.4 test registers ieee 1149.1 requires a minimum of two test registers: t he bypass register and the boundary scan register. an optional test register, the identification register, has been included with the DS26518 design. the identification register is used in conjunction with the idcode instruct ion and the test-logic-reset st ate of the tap controller. 14.4.1 boundary scan register this register contains both a shift register path and a latched parallel output for all control cells and digital i/o cells, and is n bits in length. 14.4.2 bypass register this register is a single one-bit shift register used in conjuncti on with the bypass, clamp, and highz instructions, providing a short path between jtdi and jtdo. 14.4.3 identification register the identification register co ntains a 32-bit shift register and a 32-bit latched parallel output. this register is selected during the idcode instruction and when the t ap controller is in the test-logic-reset state.
DS26518 8-port t1/e1/j1 transceiver 284 of 286 15. pin configuration 15.1 pin configuration?256-ball te-csbga 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 a ttip1 ttip1 tring1 rsync1 tchblk1/ tchclk1 tsig2 refclkio a11 a7 a1 tsig7 rsig7 tsync8/ tssyncio8 tring8 ttip8 ttip8 a b atvdd atvss tring1 tsync1/ tssyncio1 rchblk2/ rchclk2 rsync2 mclk a10 a8 a2 tsync7/ tssyncio7 rser7 tclk8 trin g8 atvss atvdd b c rtip1 rring1 spi_sel/ al/rsigf/ flos1 rmsync1/ rfsync1 tclk1 rmsync2/ rfsync2 tchblk2/ tchclk2 a12 a6 a0 rsync7 rchblk7/ rchclk7 tsig8 tsysclk8/ al/rsigf/ flos8 rring8 rtip8 c d arvdd arvss clko/ rlf/ltc1 rsig1 tsig1 rser2 tclk2 digioen a5 tchblk7/ tchclk7 rmsync7/ rfsync7 tser8 rsync8 rsysclk8/ rlf/ltc8 arvss arvdd d e arvdd arvss rsysclk2/ rlf/ltc2 rchblk1/ rchclk1 rser1 rsig2 tser2 bpclk1 a4 tclk7 tchblk8/ tchclk8 rmsync8/ rfsync8 rclk8 rsysclk7/ rlf/ltc7 arvss arvdd e f rtip2 rring2 tsysclk2/ al/rsigf/ flos2 rclk1 jtclk tser1 tsync2/ tssyncio2 a9 a3 tser7 rser8 rsig8 rclk7 tsysclk7/ al/rsigf/ flos7 rring7 rtip7 f g atvdd atvss tring2 rclk2 dvdd33 dvdd33 dvdd18 dvdd18 dvdd18 dvdd18 dvdd33 dvdd33 rchblk8/ rchclk8 tring7 atvss atvdd g h ttip2 ttip2 tring2 jtdi dvdd33 dvdd33 ac vdd dvdd33 dvdd33 dvdd33 dvdd33 dvss scanmode tring7 ttip7 ttip7 h j ttip3 ttip3 tring3 jtdo resr ef dvss acvss d vss dvss dvss dvss resetb rclk6 tring6 ttip6 ttip6 j k atvdd atvss tring3 jtms dvss dvss dvss dvss dvss d vss dvss dvss rclk5 tring6 atvss atvdd k l rtip3 rring3 tsysclk3/ al/rsigf/ flos3 rclk3 jtrst rchblk3/ rchclk3 tchblk3/ tchclk3 tclk4 d[1]/ spi_mosi tclk5 tser6 rsysclk1 txenable/ scan_en tsysclk6/ al/rsigf/ flos6 rring6 rtip6 l m arvdd arvss rsysclk3/ rlf/ltc3 rclk4 rsig3 tsync3/ tssyncio3 tsync4/ tssyncio4 rdb/ dsb d[5]/ spi_swap tser5 rser5 rser6 bts rsysclk6/ rlf/ltc6 arvss arvdd m n arvdd arvss rsysclk4/ rlf/ltc4 rser3 rsync3 rser4 tser4 d[0]/ spi_miso d[6]/ spi_cpha tsync5/ tssyncio5 tclk6 rmsync6/ rfsync6 tssyncio rsysclk5/ rlf/ltc5 arvss arvdd n p rtip4 rring4 tsysclk4/ al/rsigf/ flos4 rmsync3/ rfsync3 tclk3 rmsync4/ rfsync4 tchblk4/ tchclk4 d[2]/ spi_sclk tchblk5/ tchclk5 rmsync5/ rfsync5 tchblk6/ tchclk6 rsync6 tsysclk1 tsysclk5/ al/rsigf/ flos5 rring5 rtip5 p r atvdd atvss tring4 tser3 rsig4 tsig4 wrb/ rwb d[4] intb rsync5 rsig5 tsig6 rsig6 tring5 atvss atvdd r t ttip4 ttip4 tring4 tsig3 rsysclk/ clk4 rsync4 csb d[3] d[7]/ spi_cpol tsig5 rchblk5/ rchclk5 tsync6/ tssyncio6 rchblk6/ rchclk6 tring5 ttip5 ttip5 t 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
DS26518 8-port t1/e1/j1 transceiver 285 of 286 16. package information (the package drawing(s) in this data sheet may not reflect the most current specifications. the package number provided for each package is a link to the latest package outline information .) 16.1 256-ball te-csbga ( 56-g6028-001 )
DS26518 8-port t1/e1/j1 transceiver 286 of 286 maxim/dallas semiconductor cannot assume res ponsibility for use of any circuitry other than circuitry entirely embodied in a ma xim/dallas semiconductor product. no circuit patent licenses are implied. maxi m/dallas semiconductor reserves the right to change the circuitry and specifications without notice at any time. maxim integrated products, 120 san gabriel drive, sunnyvale, ca 94086 408-737-7600 ? 2007 maxim integrated products the maxim logo is a registered trademark of maxim integrated products, inc. the dallas logo is a registered trademark of dallas semiconductor corporation. 17. document revision history revision description 022007 new product release.

▲Up To Search▲

Price & Availability of DS26518

	To Download DS26518 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .